On Thu, Aug 14, 2008 at 12:02:50PM +0400, sam wrote: > Jeremy Chadwick wrote: >> On Thu, Aug 14, 2008 at 12:16:16AM -0700, Jeremy Chadwick wrote: >> >>> On Thu, Aug 14, 2008 at 10:57:53AM +0400, sam wrote: >>> >>>> Andrey V. Elsukov wrote: >>>> >>>>> sam wrote: >>>>> >>>>>> FreeBSD 7.0-STABLE FreeBSD 7.0-STABLE #5: Tue Aug 12 13:54:27 >>>>>> MSD 2008 root@:/usr/obj/usr/src/sys/GENERIC i386 >>>>>> |-------------------------------------------------------------------- >>>>>> >>>>>> please, any solution ? >>>>>> >>>>> Probably speed is limited via jumpers on your hard drive. >>>>> >>>>> >>>> http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1409&p_created=#jumper >>>> tried it >>>> >>>> without results >>>> >>> FWIW, the only time I've seen this happen is when there's a jumper >>> limiting the capability. You should have **removed** the OPT1 jumper, >>> and left any other jumpers alone. >>> >>> If you're absolutely sure the jumper is removed, I'll purchase one of >>> these drives and test it on an ICH7 (Supermicro PDSMi+) to confirm your >>> findings. >>> >> >> Actually, I don't need to -- I'm using WD5000AAKS disks myself on >> that exact system: >> >> atapci1: <Intel AHCI controller> port >> 0x30e8-0x30ef,0x30dc-0x30df,0x30e0-0x30e7,0x30d8-0x30db,0x30b0-0x30bf mem >> 0xe8600400-0xe86007ff irq 19 at device 31.2 on pci0 >> atapci1: [ITHREAD] >> atapci1: AHCI Version 01.10 controller with 4 ports detected >> ata2: <ATA channel 0> on atapci1 >> ata2: [ITHREAD] >> ata3: <ATA channel 1> on atapci1 >> ata3: [ITHREAD] >> ata4: <ATA channel 2> on atapci1 >> ata4: [ITHREAD] >> ata5: <ATA channel 3> on atapci1 >> ata5: [ITHREAD] >> >> ad6: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata3-master SATA300 >> ad8: 476940MB <WDC WD5000AAKS-00TMA0 12.01C01> at ata4-master SATA300 >> > may issue in <Intel ICH7 SATA300 controller> driver ? > > ---------------------------------------------------- > atapci1: <Intel ICH7 SATA300 controller> port > 0xc880-0xc887,0xc800-0xc803,0xc480-0xc487,0xc400-0xc403,0xc080-0xc08f > irq 19 at device 31.2 on pci0 > ----------------------------------------------------
Possibly. All my Intel ICH7 boards have AHCI capability, and I use it. See Chapter 4 here: http://www.supermicro.com/manuals/motherboard/3000/MNL-0889.pdf If your motherboard does, I'd recommend enabling it as well and see if things change. Regarding the "Enhanced" vs. "Compatible" mode: use Enhanced. On my boards, choosing Enhanced makes the AHCI and Intel MatrixRAID options appear. I'm fairly certain you don't need AHCI to get SATA300, though. I would recommend you re-check the jumpers on your disks to make sure you didn't make a mistake when adjusting things. -- | Jeremy Chadwick jdc at parodius.com | | Parodius Networking http://www.parodius.com/ | | UNIX Systems Administrator Mountain View, CA, USA | | Making life hard for others since 1977. PGP: 4BD6C0CB | _______________________________________________ freebsd-hackers@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-hackers To unsubscribe, send any mail to "[EMAIL PROTECTED]"
