> > Not a whole lot done, I had the MAXUSERS set to 128, though am about to
> > bump it to 256 when I rebuild to see if that helps. I used to have some
> > tunables for BSDI when I used it, but when I tried to apply them to FBSD
> > it bitched about them being unknown so I just left them out. Was also
> > going to move NMBCLUSTERS up to 20480, not sure if thats the solution or
> > not. I can post the whole config if desired, but really it's very close
> > to the GENERIC except I added SOFTUPDATES, and removed all the drivers I
> > didn't need for my system to hopefully slim it down some..
>
> grrrr, you _still_ haven't even told me how much RAM is in the box
> and what else it does if anything.
>
> Without that kind of information I'm not too comfortable giving
> advice on tuneables because I DON'T KNOW WHAT I'M TUNING :), when
> I've just blindly told people to increase NMBCLUSTERS they've had
> other problems because the kernel's network buffers wired down all
> the machine's memory.
>
> Yes, increasing NMBLCUSTERS is a good thing, but without your
> configuration it's hard to say how much to increase it.
>
> --
> -Alfred Perlstein - [[EMAIL PROTECTED]|[EMAIL PROTECTED]]
Sorry, thought you were asking about the kernel configs, not the
hardware configs. Here is my current running config via dmesg, as
I think that covers it all..
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #3: Tue Mar 7 04:20:22 EST 2000
[EMAIL PROTECTED]:/usr/src/sys/compile/U2
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (551.25-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x665 Stepping = 5
Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 402587648 (393152K bytes)
config> q
avail memory = 387334144 (378256K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc02cc000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc02cc09c.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 5
Timecounter "PIIX" frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at device 7.3 on
pci0
dc0: <Intel 21143 10/100BaseTX> port 0xd400-0xd47f mem 0xd5410000-0xd54103ff irq 17 at
device 13.0 on pci0
dc0: Ethernet address: 00:c0:f0:3b:a7:eb
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <Trident model 9660 VGA-compatible display device> at 15.0 irq 16
atapci1: <HighPoint HPT366 ATA66 controller> port
0xe000-0xe0ff,0xdc00-0xdc03,0xd800-0xd807 irq 18 at device 19.0 on pci0
atapci2: <HighPoint HPT366 ATA66 controller> port
0xec00-0xecff,0xe800-0xe803,0xe400-0xe407 irq 18 at device 19.1 on pci0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
ad0: 8693MB <ST39140A> [17662/16/63] at ata0-master using UDMA33
Mounting root from ufs:/dev/ad0s1a
WARNING: / was not properly dismounted
dc0: TX underrun -- increasing TX threshold
Did I miss anything important you need??
---
Howard Leadmon - [EMAIL PROTECTED] - http://www.abs.net
ABSnet Internet Services - Phone: 410-361-8160 - FAX: 410-361-8162
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-hackers" in the body of the message
