On Fri, 14 Apr 2000, Viren R.Shah wrote:
> Here it is:
>
> mainboard0: <CPQ1519 (System Board) on eisa0 slot 0>
> eisa0: unknown card CPQ6101 (0x0e116101) at slot 5
> ida0: <Compaq SMART array controller> at 0x6000-0x60ff, 0x6c88-0x6c9e
> ida0: irq 15 (level) on eisa0 slot 6
> ida0: drives=1 firm_rev=1.66
> idad0: 3002MB (6149631 sectors), blocksize=512
> eisa0: u
>
>
> Fatal trap 12: page fault while in kernel mode
> fault virtual address = 0xd5ff0200
> fault code = supervisor read, page not present
> instruction pointer = 0x8:0xc019733e
> stack pointer = 0x10:0xc062fde4
> frame pointer = 0x10:0xc062fe6c
> code segment = base 0x0, limit 0xfffff, type 0x1b
> DPL 0, pres 1, def32 1, gran 1
> processor eflags = interrupt enabled, resume, IOPL = 0
> current process = 0 (swapper)
> interrupt mask = net tty bio cam
> kernel: type 12 trap, code=0
> Stopped at kvprintf+0x9a: movzbl 0(%eax), %edi
>
> db> trace
>
> kvprintf(d5ff0200, 2b9005d, ff0000ad, 800ff, 2b90000) at kvprintf+0x9a
> vprintf(c02a1060, c062fec4, c0bc2500, c0b92028, c0bc2500) at vprintf+0x0x3c
> device_printf(c0bc2500, c02a1060, 43, 50, 51) at device_printf+0x1c
> eisa_probe_nomatch(c0bc2500, c0bc2300, c0bc2300, c0bc2680, c0bc2500) at
>eisa_probe_nomatch+0x114
> device_probe_and_attach(c0bc2300) at device_probe_and_attach+0x127
> bus_generic_attach(c0bc2500, c0bc2680, c087d800, c0bc2680, 0) at
>bus_generic_attach+0x16
> device_probe_and_attach(c0bc2500) at device_probe_and_attach+0x9e
> nexus_attach(c0bc2680, c0bc2680, c02c8d30, 634000, 0) at nexus_attach+0x4e
> device_probe_and_attach(c0bc2680) at device_probe_and_attach+0x9e
> root_bus_configure(c087d800, c02a31cc, 0) at root_bus_configure+0x16
> configure(0, 62dc00, 634000, 0, c011dec6) at configure+0x34
> mi_startup(c062ffb4, b0297, ffe, 634000, c0197d25) at mi_startup+0x70
> begin() at begin+0x4b
>
> I'm gonna keep it up at the ddb prompt -- if you need anything else. I
> didn't build the kernel I used with "makeoptions -g". I can do that
> next time if needed.
Well, this isn't a problem with the IDA driver (unless its stomping on
something.)
Can you boot verbose with the IDA driver kernel?
Compile a kernel without the IDA driver and boot verbose.
Give me the output of both.
--
| Matthew N. Dodd | '78 Datsun 280Z | '75 Volvo 164E | FreeBSD/NetBSD |
| [EMAIL PROTECTED] | 2 x '84 Volvo 245DL | ix86,sparc,pmax |
| http://www.jurai.net/~winter | This Space For Rent | ISO8802.5 4ever |
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
