> At every load of a PCI driver, all the non-attached drivers are
> reprobed. As a giggle, load the usb module and you see them all appear
> twice.
That is fine for unknown devices as it shown in second dmesg output.
(See lines denoted by !!!!!!!). What is the reason for message about
recognized device?
> Not at all a problem as the message is generated by DEVICE_NOMATCH.
OK. Let document it and call it "feature". ;-)
> > Every attempt to kldload any pci driver produce strange message
> > marked by ^^^^ in examples from two different computers.
> > I would call it for a while "undocumented feature".
> >
> > Copyright (c) 1992-2000 The FreeBSD Project.
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > The Regents of the University of California. All rights reserved.
> > FreeBSD 4.0-CURRENT #1: Wed Jan 19 21:48:46 MSK 2000
> > nms@Draculina:/xtra/src/sys/compile/DRACULINA
> > Timecounter "i8254" frequency 1193182 Hz
> > CPU: Pentium/P55C (233.86-MHz 586-class CPU)
> > Origin = "GenuineIntel" Id = 0x543 Stepping = 3
> > Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
> > real memory = 33554432 (32768K bytes)
> > avail memory = 30162944 (29456K bytes)
> > Preloaded elf kernel "kernel" at 0xc027b000.
> > Preloaded userconfig_script "/boot/kernel.conf" at 0xc027b09c.
> > Intel Pentium detected, installing workaround for F00F bug
> > npx0: <math processor> on motherboard
> > npx0: INT 16 interface
> > pcib0: <Host to PCI bridge> on motherboard
> > pci0: <PCI bus> on pcib0
> > isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
> > isa0: <ISA bus> on isab0
> > pci0: Intel PIIX3 ATA controller (vendor=0x8086, dev=0x7010) at 7.1
> > bt0: <Buslogic Multi-Master SCSI Host Adapter> port 0x6400-0x6403 irq 15 at device
>8.0 on pci0
> > bt0: BT-946C FW Rev. 4.25J Narrow SCSI Host Adapter, SCSI ID 7, 100 CCBs
> > vga-pci0: <S3 ViRGE DX/GX graphics accelerator> mem 0xe0000000-0xe3ffffff irq 11
>at device 9.0 on pci0
> > de0: <Digital 21140 Fast Ethernet> port 0x6800-0x687f mem 0xe4000000-0xe400007f
>irq 10 at device 10.0 on pci0
> > de0: SMC 9332DST 21140 [10-100Mb/s] pass 1.2
> > de0: address 00:00:c0:e0:9e:d0
> > de0: enabling 10baseT port
> > xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x6c00-0x6c7f mem
>0xe4001000-0xe400107f irq 12 at device 11.0 on pci0
> > xl0: Ethernet address: 00:50:04:4c:ae:5d
> > miibus0: <MII bus> on xl0
> > ukphy0: <Generic IEEE 802.3u media interface> on miibus0
> > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> > fdc0: FIFO enabled, 8 bytes threshold
> > fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> > atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
> > atkbd0: <AT Keyboard> irq 1 on atkbdc0
> > vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
> > sc0: <System console> on isa0
> > sc0: VGA <16 virtual consoles, flags=0x200>
> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> > sio0: type 16550A
> > sio1 at port 0x2f8-0x2ff irq 3 on isa0
> > sio1: type 16550A
> > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> > ppc0: FIFO with 16/16/16 bytes threshold
> > ppc1: <Parallel port> at port 0x278-0x27f irq 5 on isa0
> > ppc1: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> > IP packet filtering initialized, divert enabled, rule-based forwarding disabled,
>logging disabled
> > Waiting 3 seconds for SCSI devices to settle
> > Mounting root from ufs:/dev/da0s1a
> > da0 at bt0 bus 0 target 0 lun 0
> > da0: <FUJITSU M1606S-512 6226> Fixed Direct Access SCSI-2 device
> > da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
> > da0: 1041MB (2131992 512 byte sectors: 128H 32S/T 520C)
> > da1 at bt0 bus 0 target 1 lun 0
> > da1: <CONNER CFP2107E 2.14GB 1524> Fixed Direct Access SCSI-2 device
> > da1: 10.000MB/s transfers (10.000MHz, offset 15)
> > da1: 2048MB (4194304 512 byte sectors: 255H 63S/T 261C)
> > da2 at bt0 bus 0 target 2 lun 0
> > da2: <CONNER CFP2107E 2.14GB 1524> Fixed Direct Access SCSI-2 device
> > da2: 10.000MB/s transfers (10.000MHz, offset 15)
> > da2: 2048MB (4194304 512 byte sectors: 255H 63S/T 261C)
> > vinum: loaded
> > vinum: reading configuration from /dev/da1s1e
> > vinum: updating configuration from /dev/da2s1e
> > de0: enabling Full Duplex 10baseT port
> > pci0: Intel PIIX3 ATA controller (vendor=0x8086, dev=0x7010) at 7.1
> > ^^^^^^
> > pci0: Intel PIIX3 ATA controller (vendor=0x8086, dev=0x7010) at 7.1
> > ^^^^^^
> >
> >
> >
> > Copyright (c) 1992-2000 The FreeBSD Project.
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > The Regents of the University of California. All rights reserved.
> > FreeBSD 4.0-CURRENT #1: Tue Feb 8 15:24:28 MSK 2000
> > root@Manor:/usr/src/sys/compile/MANOR
> > Timecounter "i8254" frequency 1193182 Hz
> > CPU: Pentium II/Pentium II Xeon/Celeron (334.09-MHz 686-class CPU)
> > Origin = "GenuineIntel" Id = 0x660 Stepping = 0
> >
>Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
> > real memory = 67096576 (65524K bytes)
> > avail memory = 62672896 (61204K bytes)
> > Preloaded elf kernel "kernel" at 0xc024d000.
> > Preloaded userconfig_script "/boot/kernel.conf" at 0xc024d09c.
> > Pentium Pro MTRR support enabled
> > npx0: <math processor> on motherboard
> > npx0: INT 16 interface
> > apm0: <APM BIOS> on motherboard
> > apm: found APM BIOS v1.2, connected at v1.2
> > pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
> > pci0: <PCI bus> on pcib0
> > pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
> > pci1: <PCI bus> on pcib1
> > isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
> > isa0: <ISA bus> on isab0
> > ata-pci0: <Intel PIIX4 ATA-33 controller> port 0xd800-0xd80f at device 4.1 on pci0
> > ata0 at 0x01f0 irq 14 on ata-pci0
> > ata1 at 0x0170 irq 15 on ata-pci0
> > pci0: Intel 82371AB/EB (PIIX4) USB controller (vendor=0x8086, dev=0x7112) at 4.2
>irq 5
> > chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at device
>4.3 on pci0
> > vga-pci0: <S3 ViRGE graphics accelerator> mem 0xc8000000-0xcbffffff irq 12 at
>device 10.0 on pci0
> > pci0: unknown card (vendor=0x108d, dev=0x0008) at 11.0 irq 10
!!!!!!!!!!!
> > pci0: unknown card (vendor=0x10b7, dev=0x9050) at 12.0 irq 11
!!!!!!!!!!!
> > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> > fdc0: FIFO enabled, 8 bytes threshold
> > fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> > atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
> > atkbd0: <AT Keyboard> irq 1 on atkbdc0
> > sc0: <System console> on isa0
> > sc0: VGA <16 virtual consoles, flags=0x200>
> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> > sio0: type 16550A
> > sio1 at port 0x2f8-0x2ff irq 3 on isa0
> > sio1: type 16550A
> > IP packet filtering initialized, divert enabled, rule-based forwarding disabled,
>logging disabled
> > ad0: 4125MB <FUJITSU MPD3043AT> [8940/15/63] at ata0-master using UDMA33
> > ad1: 19470MB <IBM-DJNA-352030> [39560/16/63] at ata1-master using UDMA33
> > acd0: CDROM <40X CD-ROM> at ata0-slave using PIO4
> > Mounting root from ufs:/dev/ad0a
> > pci0: Intel 82371AB/EB (PIIX4) USB controller (vendor=0x8086, dev=0x7112) at 4.2
>irq 5
> > ^^^^^^
> > pci0: unknown card (vendor=0x108d, dev=0x0008) at 11.0 irq 10
!!!!!!!!!!!
> > xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xb800-0xb83f irq 11 at device 12.0 on
>pci0
> > xl0: Ethernet address: 00:00:62:a1:61:20
> > miibus0: <MII bus> on xl0
> > nsphy0: <DP83840 10/100 media interface> on miibus0
> > nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > pci0: Intel 82371AB/EB (PIIX4) USB controller (vendor=0x8086, dev=0x7112) at 4.2
>irq 5
> > ^^^^^^
> > ol0: <Olicom RapidFire 3540 100/16/4 Adapter (OC-3540)> port 0xd000-0xd03f mem
>0xc7800000-0xc7803fff irq 10 at devi
> ce 11.0 on pci0
> > ol0: MAC address 00:00:83:16:d1:bd
> > ol0: adapter self-test complete (status=0)
> > pci0: Intel 82371AB/EB (PIIX4) USB controller (vendor=0x8086, dev=0x7112) at 4.2
>irq 5
> > ^^^^^^
> > pci0: Intel 82371AB/EB (PIIX4) USB controller (vendor=0x8086, dev=0x7112) at 4.2
>irq 5
> > ^^^^^^
> > pci0: Intel 82371AB/EB (PIIX4) USB controller (vendor=0x8086, dev=0x7112) at 4.2
>irq 5
> > ^^^^^^
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
