On Wed, Feb 02, 2000 at 12:16:41AM +0100, Arjan de Vet wrote:
> I did it after I upgraded to 4.0-current. The old 3.4-stable rc scripts
> may give some small warnings but these are harmless.
Worked for me, thanks !
On Wed, Feb 02, 2000 at 12:04:55AM -0800, Kris Kennaway wrote:
> Before, because (in general) it may not boot to multiuser mode at all
> otherwise.
Well, this time it worked doing it after reboot ;-)
But I'll be warned.
Problems that remain on my P5 233 notebook:
a) Xircom Card isn't detected
Though I get a message during boot:
devclass_alloc_unit: xe0 already exists, using next available unit number
Ejecting and reinserting doesn't cure the problem.
b) Can't mount cdrom
mount /cdrom
Device busy
But I'm not under /cdrom and doesn't have a CD mounted
/etc/fstab
==========
# Device Mountpoint FStype Options Dump Pass#
/dev/wd0s2b none swap sw 0 0
/dev/wd0s2a / ufs rw 1 1
/dev/wd0s1 /dos msdos ro 0 0
/dev/wd0s2f /usr ufs rw 2 2
/dev/wd0s2e /var ufs rw 2 2
proc /proc procfs rw 0 0
/dev/acd0a /cdrom cd9660 ro,noauto 0 0
/dev/fd0a /floppy msdos rw,noauto 0 0
Output of "mount" command
=========================
/dev/wd0s2a on / (ufs, local, writes: sync 1620 async 3507, reads: sync 310 async 10)
/dev/wd0s1 on /dos (msdos, NFS exported, local, read-only, reads: sync 1 async 0)
/dev/wd0s2f on /usr (ufs, NFS exported, local, soft-updates, writes: sync 375 async
3156, reads: sync 3057 async 19)
/dev/wd0s2e on /var (ufs, NFS exported, local, soft-updates, writes: sync 259 async
513, reads: sync 55 async 6)
procfs on /proc (procfs, local)
pid135@laptop:/host on /host (nfs)
pid135@laptop:/net on /net (nfs)
/dev/fd0a on /floppy (msdos, local, writes: sync 6 async 63, reads: sync 1 async 0)
Output of dmesg
===============
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #0: Wed Feb 2 20:11:23 CET 2000
[EMAIL PROTECTED]:/usr/src/sys/compile/LAPTOP
Calibrating clock(s) ... TSC clock: 232522148 Hz, i8254 clock: 1193157 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium/P55C (232.53-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x543 Stepping = 3
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory = 67108864 (65536K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x002d2000 - 0x03ff7fff, 64118784 bytes (15654 pages)
avail memory = 62181376 (60724K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00ec050
bios32: Entry = 0xee600 (c00ee600) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x263e
pnpbios: Found PnP BIOS data at 0xc00ff000
pnpbios: Entry = ea000:13de Rev = 1.0
pnpbios: OEM ID 744e
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc02b9000.
Intel Pentium detected, installing workaround for F00F bug
md0: Malloc disk
Creating DISK md0
pci_open(1): mode 1 addr port (0x0cf8) is 0x800008b0
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=04061039)
npx0: <math processor> on motherboard
npx0: INT 16 interface
i586_bzero() bandwidth = 644329896 bytes/sec
bzero() bandwidth = 331345261 bytes/sec
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=04061039)
pcib0: <SiS 85c501> on motherboard
found-> vendor=0x1039, dev=0x0406, revid=0x00
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1039, dev=0x0008, revid=0x01
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1039, dev=0x0601, revid=0x01
class=01-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base 00000174, size 2
map[14]: type 1, range 32, base 000001f4, size 2
map[18]: type 1, range 32, base 00000374, size 2
map[1c]: type 1, range 32, base 000003f4, size 2
found-> vendor=0x1023, dev=0x9660, revid=0xd3
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 1, range 32, base 08000000, size 22
map[14]: type 1, range 32, base 08800000, size 16
map[18]: type 1, range 32, base 08400000, size 22
found-> vendor=0x119b, dev=0x1221, revid=0x02
class=06-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=0
map[10]: type 1, range 32, base 000003e0, size 2
found-> vendor=0x119b, dev=0x1221, revid=0x02
class=06-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=0
map[10]: type 1, range 32, base 000003e4, size 2
pci0: <PCI bus> on pcib0
isab0: <SiS 85c503 PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
ata-pci0: <Unknown PCI ATA controller (generic mode)> port
0x3f4-0x3f7,0x374-0x377,0x1f4-0x1f7,0x174-0x177 at device 1.1 on pci0
ata-pci0: Busmastering DMA not supported
ata2: iobase=0x0174 altiobase=0x01f4 bmaddr=0x0000
ata2: mask=00 status0=ff status1=ff
ata3: iobase=0x0374 altiobase=0x03f4 bmaddr=0x0000
ata3: mask=03 status0=13 status1=13
ata3: mask=03 status0=13 status1=13
ata3: devices = 0x3
ata_pciattach: Unable to alloc interrupt
ata3 at 0x0374 irq 0 on ata-pci0
vga-pci0: <Trident model 9660 VGA-compatible display device> mem
0x8400000-0x87fffff,0x8800000-0x880ffff,0x8000000-0x83fffff at device 6.0 on pci0
chip1: <PCI to PCMCIA bridge (vendor=119b device=1221)> port 0x3e0-0x3e3 irq 0 at
device 13.0 on pci0
chip2: <PCI to PCMCIA bridge (vendor=119b device=1221)> port 0x3e4-0x3e7 irq 0 at
device 14.0 on pci0
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x0000
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0 at port 0x1f0 irq 14 on isa0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata1: mask=03 status0=50 status1=01
ata1: mask=03 status0=00 status1=01
ata1: devices = 0xc
ata1 at port 0x170 irq 15 on isa0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0067
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 1c 03 3c
psm: status 1c 03 3c
psm: status 1c 03 3c
psm: status 10 00 64
psm: data 08 00 00
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic: management irq 10
pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 irq 10 on isa0
pccard0: <PC Card bus -- kludge version> on pcic0
pccard1: <PC Card bus -- kludge version> on pcic0
pcic1: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: parallel port found at 0x378
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03127f3f 0..786=787 cylinders, 0..127=128 heads, 1..63=63 sectors
1:03feff00 0..1022=1023 cylinders, 0..255=256 heads, 1..0=0 sectors
2:03fdfe3f 0..1021=1022 cylinders, 0..254=255 heads, 1..63=63 sectors
3:03fe0200 0..1022=1023 cylinders, 0..2=3 heads, 1..0=0 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
pccard: card inserted, slot 0
pccard: card inserted, slot 1
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ata3-slave: ata_command: timeout waiting for intr
ata3-slave: identify failed
ata3-master: ata_command: timeout waiting for intr
ata3-master: identify failed
ad0: <HITACHI_DK237A-32/00U0A0A0> ATA-3 disk at ata0 as master
ad0: 3102MB (6354432 sectors), 6304 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, BIOSPIO
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
Creating DISK ad0
Creating DISK wd0
ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
acd0: <CD-220EA/1.0A> CDROM drive at ata1 as master
acd0: read 3445KB/s (3445KB/s), 128KB buffer, BIOSPIO
acd0: Reads: CD-R, CD-DA stream
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Mounting root from ufs:/dev/wd0s2a
wd0s1: type 0xb, start 63, end = 3693311, size 3693249 : OK
wd0s2: type 0xa5, start 3693312, end = 6354431, size 2661120 : OK
start_init: trying /sbin/init
devclass_alloc_unit: xe0 already exists, using next available unit number
Linux-ELF exec handler installed
splash: image decoder found: daemon_saver
pid 257 (man), uid 9 on /usr: file system full
pccard: card removed, slot 0
pccard: card inserted, slot 0
devclass_alloc_unit: xe0 already exists, using next available unit number
pccard: card removed, slot 0
pccard: card inserted, slot 0
devclass_alloc_unit: xe0 already exists, using next available unit number
pccard: card removed, slot 0
pccard: card inserted, slot 0
devclass_alloc_unit: xe0 already exists, using next available unit number
pccard: card removed, slot 0
pccard: card inserted, slot 0
kernel config file
==================
machine i386
cpu I586_CPU
ident LAPTOP
maxusers 64
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options INET #InterNETworking
options FFS #Fast filesystem
options FFS #Berkeley Fast Filesystem
options SOFTUPDATES #Softupdates
options FFS_ROOT #FFS usable as root device [keep this!]
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options UCONSOLE #Allow users to grab the console
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extentions
options _KPOSIX_PRIORITY_SCHEDULING
options _KPOSIX_VERSION=199309L
options ICMP_BANDLIM # Rate limit bad replies
device isa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power Management
# PCCARD (PCMCIA) support
device card
device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd0000
device pcic1 at isa? irq 11 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
# requires PCCARD (PCMCIA) support to be activated
#device xe0 at isa?
device xe0 at isa? port? irq ?
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
--
Andreas Klemm http://www.FreeBSD.ORG/~andreas
http://www.freebsd.org/~fsmp/SMP/SMP.html
powered by Symmetric MultiProcessor FreeBSD
Get new songs from our band: http://www.freebsd.org/~andreas/64bits/index.html
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
