I think you're right. For example, here's one that's pretty close:
https://www.hobbytown.com/gens-ace-4s-lihv-100c-lipo-battery-pack-15.2v-7500mah-ga-b1102/p779337
Did I do the math right ?
capacity 7.5Ah
rate: 100C
volts: 15.2
That's
capacity 7.5 * 15.2 = 114Wh
rate: 100 * 114 = 11.4kW
Peri
------ Original Message ------
From: "Lawrence Winiarski" <[email protected]>
To: "Electric Vehicle Discussion List" <[email protected]>; "Peri
Hartman" <[email protected]>
Sent: 13-Apr-20 10:22:34 PM
Subject: Re: [EVDL] custom battery
Isn't 60c or 100C common in Radio Control stuff now? Lots of
solutions there.
On Monday, April 13, 2020, 9:51:43 PM PDT, Peri Hartman via EV
<[email protected]> wrote:
Nominally 240. But it really can be anything and I can convert it to
what I need.
Peri
------ Original Message ------
From: "Alan Arrison via EV" <[email protected]>
To: [email protected]
Cc: "Alan Arrison" <[email protected]>
Sent: 13-Apr-20 9:48:53 PM
Subject: Re: [EVDL] custom battery
>That sounds like almost super-capacitor territory. What voltage is
needed?
>
>Designing and implementing a BMS is something even EE's have trouble
with.
>
>However, if the voltage is low enough, it makes it much easier.
>
>Al
>
>On 4/14/2020 12:33 AM, Peri Hartman via EV wrote:
>>Hi,
>>
>>I need a battery with about 150Wh and a discharge rate of 8kW for up
to a minute or so. I've spent a few hours searching and there doesn't
seem to be anything on the market that fits this. There are, of course,
higher capacity batteries that can deliver 8kW, but that's not what I'm
after.
>>
>>This isn't for an EV, so I suppose this is somewhat off topic,
although BMSs are a relevant topic to EVs. It's for a home appliance
that I'm prototyping.
>>
>>I'm pretty sure I can find affordable cells that I can put together
to do this, but then I'm stuck with a custom BMS. I suspect that's the
route I'm going to have to take. So, let's talk about that.
>>
>>Each cell (or group of parallel cells) needs a monitoring circuit (is
there a name for this?). And theses monitors need to communicate with a
BMS. I'm less concerned about designing the BMS as I think I can use an
arduino and do it in software. The arduino can control the charger,
too. I can revisit this later. But for the monitors, I need to get it
right. Since the battery will be in the house, it cannot cause a fire.
Ever. Of course, I will have over temperature sensors which shut off
the charger and shut off the load.
>>
>>Here's what I think each monitor's role is, based on what I've read
on EVDL over the years and some common sense :)
>>- cell over voltage
>>- cell under voltage
>>- cell over current
>>- cell temperature
>>In all of the above the circuit should shunt the cell.
>>In addition, the monitor should constantly report the cell voltage,
current, and temp to the BMS.
>>
>>If there's something reliable I can buy, at a reasonable price,
that's my first choice. Otherwise, I guess it's getting someone to help
design and fabricate these.
>>
>>I would be grateful for your suggestions.
>>
>>Peri
>>-------------- next part --------------
>>An HTML attachment was scrubbed...
>>URL:
<http://lists.evdl.org/private.cgi/ev-evdl.org/attachments/20200414/ccfe4eb7/attachment.html>
>>_______________________________________________
>>UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
>>ARCHIVE: http://www.evdl.org/archive/index.html
>>INFO: http://lists.evdl.org/listinfo.cgi/ev-evdl.org
>>Please discuss EV drag racing at NEDRA
(http://groups.yahoo.com/group/NEDRA)
>>
>_______________________________________________
>UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
>ARCHIVE: http://www.evdl.org/archive/index.html
>INFO: http://lists.evdl.org/listinfo.cgi/ev-evdl.org
>Please discuss EV drag racing at NEDRA
(http://groups.yahoo.com/group/NEDRA)
>
_______________________________________________
UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
ARCHIVE: http://www.evdl.org/archive/index.html
INFO: http://lists.evdl.org/listinfo.cgi/ev-evdl.org
Please discuss EV drag racing at NEDRA
(http://groups.yahoo.com/group/NEDRA)
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.evdl.org/private.cgi/ev-evdl.org/attachments/20200414/497f51c5/attachment.html>
_______________________________________________
UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
ARCHIVE: http://www.evdl.org/archive/index.html
INFO: http://lists.evdl.org/listinfo.cgi/ev-evdl.org
Please discuss EV drag racing at NEDRA (http://groups.yahoo.com/group/NEDRA)
