Thank you. That worked. Kind regards, Rich
Rich Colvin [email protected]  Memento mori sic memento vivere! > On Jul 11, 2026, at 00:55, Luca Toniolo <[email protected]> wrote: > > In the > > [EMC] > > Section of your .ini > > Set > > VERSION = 1.1 > > That should stop the ini update tool > > On July 11, 2026 10:57:28 AM GMT+08:00, "rich.colvin--- via Emc-users" > <[email protected]> wrote: >> Andy, >> >> How do we turn the pop up screen off which wants to upgrade the files? >> >> Kind regards, >> Rich >> >> You are born weak and frail, and you die weak and frail. What you do >> between those is up to you. >> >>> On Jul 9, 2026, at 18:41, andy pugh <[email protected]> wrote: >>> >>> ### LinuxCNC 2.9.10 has been released. >>> >>> "What happened to 2.9.9?" you might ask. The answer is that it was briefly >>> released then withdrawn when it was found that a bug-fix had broken >>> existing configs which were working-round the bug. >>> Context in this [forum >>> thread](https://forum.linuxcnc.org/38-general-linuxcnc-questions/58927-g38-2-weird-behaviour?start=0) >>> >>> Changelog for 2.9.10: >>> >>> * Merge pull request #4219 from grandixximo/fix/4216-applied-tlo-params >>> * tests: restore #5401-#5409 loaded-offset assertions >>> * interp: split loaded vs applied tool offset params (#5401-#5409, >>> #5081-#5089) >>> * Merge pull request #4211 from BsAtHome/fix_libboost_python-versioning-2.9 >>> * build: Select the libboost_python matching the python version. >>> >>> >>> # And here is the 2.9.9 release note: # >>> >>> This is a bugfix, feature improvement, and security enhancement release. >>> >>> To address the last part first, it has been noted by two separate people >>> that a weakness in the RTAPI allows for privilege escalation as it runs >>> as setuid root (to give direct access to hardware). >>> Given the use-case for most LinuxCNC machines this is unlilely to be a >>> problem in the majority cases; most hobby users will have root access >>> anyway. The issue has been patched in both 2.9 and in the development >>> branch. >>> >>> Abbreviated Changelog for 2.9.9: >>> >>> * Merge pull request #4190 from tzuohann/check_config-2.9-datatypes >>> * Merge pull request #4188 from grandixximo/fix/genclean-soname-2.9 >>> * Merge pull request #4122 from >>> Sigma1912/2_9_gremlin_initialize_with_current_modal_gcodes >>> * Merge pull request #4168 from >>> grandixximo/backport/machine-coord-params-2.9 >>> * Merge pull request #4176 from hdiethelm/ci_doc_build_2.9 >>> * check_config: assert INI datatypes before comparing limits >>> * Various CI improvements (little user impact) >>> * Merge pull request #4166 from grandixximo/fix-4165-emccalib-iniref >>> * interp: expose absolute machine position as #5021-#5029 >>> * emccalib: ignore ini refs embedded in pin names >>> * Touchy: Backport updates from master >>> * Merge pull request #4164 from >>> grandixximo/backport/3996-tool-offset-params-2.9 >>> * tests: update tool offset assertions for #5401-#5409 applied semantics >>> * docs: G38 probe to machine-coordinate conversion via #5401-#5409 >>> * interp: make #5401-#5409 the applied tool length offset >>> * halscope improvements >>> * gremlin: Initialize preview interpreter with active modal gcodes >>> * Merge pull request #4022 from >>> wucke13/dev/wucke13/backport-preempt-rt-detection-for-6.12-and-later >>> * Merge pull request #4015 from grandixximo/fix/3994-axis-touchoff-jog-2.9 >>> * axis gui improvements >>> * Improvements in Xenomai realtime support >>> * Fix rtapi_app: Sanitize name for module addresses >>> * radiobutton: A new HAL component to select between mutually-exclusive >>> states >>> * halshow: fix broken menu item: Watch -> Add pin/signal/parameter >>> * Fix Gmoccapy screen resizing issue #3899 >>> * rtapi: Refuse to load uspace components missing rtapi_app_exit >>> * Merge pull request #3898 from NTULINUX/2.9_libedit >>> * Move python3-poppler-qt5 to "Suggests" addresses Debian bug #1129683 >>> * Move python3-poppler-qt5 to "Recommends". Issue #3872 addresses >>> Debian bug #1129683 >>> * Merge pull request #3790 from mark-v-d/2.9 (lathe cycles) >>> * hm2_modbus fixes >>> * fix: emc/canterp: passing right value for SPINDLE_ORIENTATION >>> * Adding testcase for 6bf62870da5866a237bdd8531e28f33644255164 >>> endless loop in g71 fix. >>> * If statement should not be nested. This causes the hal component >>> to ignore the enable state of each axis range. >>> * qtdragon - various updates >>> * gmoccapy - various updates >>> >>> The full changelog can be found at >>> https://github.com/LinuxCNC/linuxcnc/blob/2.9/debian/changelog >>> >>> As usual I would like to thank all the LinuxCNC developers and >>> testers, especially the following who contributed directly to this >>> release: >>> >>> * Alec Ari >>> * Bertho Stultiens >>> * BsAtHome >>> * CMorley >>> * david mueller >>> * Hannes Diethelm >>> * Hans Unzner >>> * Jerry Trantow >>> * Luca Toniolo >>> * Mark >>> * mark-v-d >>> * Roy >>> * Sean Froome >>> * Steffen Moeller >>> * tzuohann >>> >>> The LinuxCNC repositories have been updated for Buster, Bullseye, >>> Bookworm, Trixie and Sid. >>> >>> Note that released debs are also now available on the LinuxCNC GitHub >>> under “Releases”: www.github.com/https://github.com/LinuxCNC/linuxcnc >>> >>> Happy Machining! >>> >>> >>> -- >>> atp >>> "A motorcycle is a bicycle with a pandemonium attachment and is >>> designed for the especial use of mechanical geniuses, daredevils and >>> lunatics." >>> — George Fitch, Atlanta Constitution Newspaper, 1912 >>> >>> >>> _______________________________________________ >>> Emc-users mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users > > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
