In the [EMC]
Section of your .ini Set VERSION = 1.1 That should stop the ini update tool On July 11, 2026 10:57:28 AM GMT+08:00, "rich.colvin--- via Emc-users" <[email protected]> wrote: >Andy, > >How do we turn the pop up screen off which wants to upgrade the files? > >Kind regards, >Rich > >You are born weak and frail, and you die weak and frail. What you do between >those is up to you. > >> On Jul 9, 2026, at 18:41, andy pugh <[email protected]> wrote: >> >> ### LinuxCNC 2.9.10 has been released. >> >> "What happened to 2.9.9?" you might ask. The answer is that it was briefly >> released then withdrawn when it was found that a bug-fix had broken >> existing configs which were working-round the bug. >> Context in this [forum >> thread](https://forum.linuxcnc.org/38-general-linuxcnc-questions/58927-g38-2-weird-behaviour?start=0) >> >> Changelog for 2.9.10: >> >> * Merge pull request #4219 from grandixximo/fix/4216-applied-tlo-params >> * tests: restore #5401-#5409 loaded-offset assertions >> * interp: split loaded vs applied tool offset params (#5401-#5409, >> #5081-#5089) >> * Merge pull request #4211 from BsAtHome/fix_libboost_python-versioning-2.9 >> * build: Select the libboost_python matching the python version. >> >> >> # And here is the 2.9.9 release note: # >> >> This is a bugfix, feature improvement, and security enhancement release. >> >> To address the last part first, it has been noted by two separate people >> that a weakness in the RTAPI allows for privilege escalation as it runs >> as setuid root (to give direct access to hardware). >> Given the use-case for most LinuxCNC machines this is unlilely to be a >> problem in the majority cases; most hobby users will have root access >> anyway. The issue has been patched in both 2.9 and in the development >> branch. >> >> Abbreviated Changelog for 2.9.9: >> >> * Merge pull request #4190 from tzuohann/check_config-2.9-datatypes >> * Merge pull request #4188 from grandixximo/fix/genclean-soname-2.9 >> * Merge pull request #4122 from >> Sigma1912/2_9_gremlin_initialize_with_current_modal_gcodes >> * Merge pull request #4168 from >> grandixximo/backport/machine-coord-params-2.9 >> * Merge pull request #4176 from hdiethelm/ci_doc_build_2.9 >> * check_config: assert INI datatypes before comparing limits >> * Various CI improvements (little user impact) >> * Merge pull request #4166 from grandixximo/fix-4165-emccalib-iniref >> * interp: expose absolute machine position as #5021-#5029 >> * emccalib: ignore ini refs embedded in pin names >> * Touchy: Backport updates from master >> * Merge pull request #4164 from >> grandixximo/backport/3996-tool-offset-params-2.9 >> * tests: update tool offset assertions for #5401-#5409 applied semantics >> * docs: G38 probe to machine-coordinate conversion via #5401-#5409 >> * interp: make #5401-#5409 the applied tool length offset >> * halscope improvements >> * gremlin: Initialize preview interpreter with active modal gcodes >> * Merge pull request #4022 from >> wucke13/dev/wucke13/backport-preempt-rt-detection-for-6.12-and-later >> * Merge pull request #4015 from grandixximo/fix/3994-axis-touchoff-jog-2.9 >> * axis gui improvements >> * Improvements in Xenomai realtime support >> * Fix rtapi_app: Sanitize name for module addresses >> * radiobutton: A new HAL component to select between mutually-exclusive >> states >> * halshow: fix broken menu item: Watch -> Add pin/signal/parameter >> * Fix Gmoccapy screen resizing issue #3899 >> * rtapi: Refuse to load uspace components missing rtapi_app_exit >> * Merge pull request #3898 from NTULINUX/2.9_libedit >> * Move python3-poppler-qt5 to "Suggests" addresses Debian bug #1129683 >> * Move python3-poppler-qt5 to "Recommends". Issue #3872 addresses >> Debian bug #1129683 >> * Merge pull request #3790 from mark-v-d/2.9 (lathe cycles) >> * hm2_modbus fixes >> * fix: emc/canterp: passing right value for SPINDLE_ORIENTATION >> * Adding testcase for 6bf62870da5866a237bdd8531e28f33644255164 >> endless loop in g71 fix. >> * If statement should not be nested. This causes the hal component >> to ignore the enable state of each axis range. >> * qtdragon - various updates >> * gmoccapy - various updates >> >> The full changelog can be found at >> https://github.com/LinuxCNC/linuxcnc/blob/2.9/debian/changelog >> >> As usual I would like to thank all the LinuxCNC developers and >> testers, especially the following who contributed directly to this >> release: >> >> * Alec Ari >> * Bertho Stultiens >> * BsAtHome >> * CMorley >> * david mueller >> * Hannes Diethelm >> * Hans Unzner >> * Jerry Trantow >> * Luca Toniolo >> * Mark >> * mark-v-d >> * Roy >> * Sean Froome >> * Steffen Moeller >> * tzuohann >> >> The LinuxCNC repositories have been updated for Buster, Bullseye, >> Bookworm, Trixie and Sid. >> >> Note that released debs are also now available on the LinuxCNC GitHub >> under “Releases”: www.github.com/https://github.com/LinuxCNC/linuxcnc >> >> Happy Machining! >> >> >> -- >> atp >> "A motorcycle is a bicycle with a pandemonium attachment and is >> designed for the especial use of mechanical geniuses, daredevils and >> lunatics." >> — George Fitch, Atlanta Constitution Newspaper, 1912 >> >> >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users > > >_______________________________________________ >Emc-users mailing list >[email protected] >https://lists.sourceforge.net/lists/listinfo/emc-users _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
