In the m-codes you sent. M110 set onVal and offVal while I use edm.t.off and edm.t.on M112 set ipkval while I did not have M198 set AtMinTix and AtMaxTix while I do not have M199 set AdvLimVal and RetLimVal while I do not have
Output signals: edm.t.Off edm.t.On edm.u.Ionization edm.u.Sparc Input signals: edm.u.Open edm.u.Seat edm.i edm.ionizationCnt edm.sparcCnt I think it would be good if it is possible to use more or less standard or at least common *-code for EDM generator. Then I think standard signal names must be defined for the *-code or how do they find the correct signal-/pin-name? Suitable parameters for control of spindle have been figured out a long time ago http://linuxcnc.org/docs/html/man/man9/motion.9.html On Mon, 26 Dec 2016 21:50:36 +0700 TJoseph Powderly <[email protected]> wrote: > interesting AGie stuff > please look at > http://www.gfms.com/content/dam/gfac/proddb/edm/die-sinking/en/agiecharmilles-form-200-ms_en.pdf > for a bit more screenshots > remember, this is for a proprietary machine, and will be of limited use > what is good though, is they actualy asked users to evaluate the user > interface before forcing it onto all the users > GF is George FIscher, the auto body company, ( and a lot more) > they bought up AGie Charmilles Elox and other edm mfctrs over the years > (the borg of edm, so they have acquired a LOT of edm knowledge ) > > i was head of AGie sink edm for a while back in the day, sort of by default, > no one else knew what the hell those machine were, and they only wanted > to play on wedm anyway > (eeeoooow its oily and dirty eeeooooow) > > regards > TomP tjtr33 > On 12/26/16 19:46, Nicklas Karlsson wrote: > >> ... > >> please tell us more of what you try to control with all those flushing > >> controls! > >> it seems there is magnitude of flush, and type of flush(pressure / > >> vacuum), and tank fill and dump > > The flushing controls are coils I found inside the machine and I have not > > yet figured out how to use them. I added a button so I could turn them > > off/on, there are also a few LEDs with no use. I think lubrification should > > be started then machine is enabled? > > > > It is possible to adjust tOff/tOn time and a meter for gap voltage, there > > are few buttons left over from example. I spent a just a few hours on the > > user interface and are right now thinking about how it should look and more > > or less standard *-codes for parameters for generator, I also have found > > m-codes you sent earlier. > > > > > > I have found Charmilles have a new standard user interface > > http://www.mfgnewsweb.com/archives/4/37497/Controls-dec12/New-Standard-User-Interface-for-Sinker-EDM-Machines.aspx > > > > > >> the area 'Settings' could be anything from on & off time to > >> cuttime/jumpdistance/frequency. > >> the 'Command' area is understandable > >> regards, & merry Christmas > >> tomp tjtr33 > >> On 12/25/16 21:54, Nicklas Karlsson wrote: > >>>>> Happen to know any more or less g-codes for these motions? g-codes > >>>>> for control of flush? g-codes for control of EDM power source? > >>>> ... i uploaded mcodes before with python commands to change edm > >>>> generator on/off/current/polarity > >>> I could remember I god some g-code suitable for EDM and are looking > >>> for them right now. I have entered g-code for Linuxcnc and Sodick wire > >>> EDM in a database, there a problem with a few codes. The database > >>> could be rather useful if filled in for more machines and put on the > >>> web. I have never machined run a machine and think it could be a good > >>> start to read thru which codes are available. > >>> ------------------------------------------------------------------------------ > >>> Developer Access Program for Intel Xeon Phi Processors Access to Intel > >>> Xeon Phi processor-based developer platforms. With one year of Intel > >>> Parallel Studio XE. Training and support from Colfax. Order your > >>> platform today.http://sdm.link/intel > >>> _______________________________________________ Emc-users mailing list > >>> [email protected] > >>> https://lists.sourceforge.net/lists/listinfo/emc-users > >> ------------------------------------------------------------------------------ > >> Developer Access Program for Intel Xeon Phi Processors > >> Access to Intel Xeon Phi processor-based developer platforms. > >> With one year of Intel Parallel Studio XE. > >> Training and support from Colfax. > >> Order your platform today.http://sdm.link/intel > >> _______________________________________________ > >> Emc-users mailing list > >> [email protected] > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > ------------------------------------------------------------------------------ > > Developer Access Program for Intel Xeon Phi Processors > > Access to Intel Xeon Phi processor-based developer platforms. > > With one year of Intel Parallel Studio XE. > > Training and support from Colfax. > > Order your platform today.http://sdm.link/intel > > > > > > _______________________________________________ > > Emc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-users > > ------------------------------------------------------------------------------ > Developer Access Program for Intel Xeon Phi Processors > Access to Intel Xeon Phi processor-based developer platforms. > With one year of Intel Parallel Studio XE. > Training and support from Colfax. > Order your platform today.http://sdm.link/intel > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Developer Access Program for Intel Xeon Phi Processors Access to Intel Xeon Phi processor-based developer platforms. With one year of Intel Parallel Studio XE. Training and support from Colfax. Order your platform today.http://sdm.link/intel _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
