I can confirm the very hight CPU Usage of gscreen gaxis! I use an AMD ATHLON X2-4800+ with 2 GB Ram, not optimized, so no isolcpus etc, because I use this one as development PC.
Gcsreen Gaxis uses 70 % of CPU 2 and 30 % of CPU 1. If I startAXIS; It uses aprox the samne amount of CPU Usage. Original gmoccapy with gscreen background uses 99 % of CPU 1 and 35 % of CPU 2. I am just making gmoccapy stand alone and I try to optimize as much as possible. I can't give values of the CPU usage yezt. Norbert Am 07.02.2014 16:45, schrieb Mark Tucker: > Chris > > I don't recall any emc_stat widget in the tutorial but i may be wrong. > I will load up the glade file on my developer os and check > > Yes i did try the Gaxis no live plot but i had lots of errors etc and > thought i would write my own. > Big mistake!!! > 1 week later and a lot less hair,and i am just scratching the surface. > > On 07/02/14 15:38, Chris Morley wrote: >> Do you have an emc_stat widget in the glade file? >> When you say gscreen uses 90% cpu, which skin if gscreen? Gaxis no-gui >> should be the least cpu hungry. Gaxis second least. >> >> Chris M >> >> ----- Reply message ----- >> From: "Mark Tucker" <[email protected]> >> To: "Enhanced Machine Controller (EMC)" <[email protected]> >> Subject: [Emc-users] John Thorntons Gui3 Sample in Linuxcnc 2.6pre >> Date: Fri, Feb 7, 2014 6:01 AM >> >> >> Andy >> >> I had already changed the comment to your version but i still have the >> same results. >> Everything works fine with axis and Gscreen but it will not work with my >> custom Gui. >> At the end of the day it must be something in the Gui. >> I just followed JT's tutorials and it worked fine until i try to put it >> in a real setup. >> >> All i wish to do at the end of the day is write a simple Gui for >> machinekit that shows the needed info for running a cnc,but without the >> cpu usage that Gscreen etc uses. >> >> The simpler standard Gui examples like Mini etc do not even show the >> current feedrate etc. >> >> I thought it might be easier to write my own but unfortunately there >> seems to be a total lack of current up to date info on this >> process,other than johns tutorials. >> >> As an example when using Gscreen/Machinekit cpu usage is about 90% when >> idle??? >> When using mini etc it is around 14%. >> >> >> >> On 07/02/14 13:23, andy pugh wrote: >>> On 7 February 2014 11:16, Mark Tucker <[email protected]> wrote: >>> >>>> I now have the following lines in my Hal file:- >>>> >>>> newsig test bit >>>> sets test 1 >>>> net test iocontrol.0.emc-enable-in >>>> >>>> Is this not enough to enable the power button >>> It should work. >>> setp iocontrol.0.emc-enable-in 1 >>> would be shorter. >>> >> ------------------------------------------------------------------------------ >> Managing the Performance of Cloud-Based Applications >> Take advantage of what the Cloud has to offer - Avoid Common Pitfalls. >> Read the Whitepaper. >> http://pubads.g.doubleclick.net/gampad/clk?id=121051231&iu=/4140/ostg.clktrk >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users >> ------------------------------------------------------------------------------ >> Managing the Performance of Cloud-Based Applications >> Take advantage of what the Cloud has to offer - Avoid Common Pitfalls. >> Read the Whitepaper. >> http://pubads.g.doubleclick.net/gampad/clk?id=121051231&iu=/4140/ostg.clktrk >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> > > ------------------------------------------------------------------------------ > Managing the Performance of Cloud-Based Applications > Take advantage of what the Cloud has to offer - Avoid Common Pitfalls. > Read the Whitepaper. > http://pubads.g.doubleclick.net/gampad/clk?id=121051231&iu=/4140/ostg.clktrk > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > ------------------------------------------------------------------------------ Managing the Performance of Cloud-Based Applications Take advantage of what the Cloud has to offer - Avoid Common Pitfalls. Read the Whitepaper. http://pubads.g.doubleclick.net/gampad/clk?id=121051231&iu=/4140/ostg.clktrk _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
