Agreed – though that is on the basis that each module “needs” a ground – maybe consider clauses such as 8.2.3 which cover continuity of bonding during routine maintenance
As for the terminal blocks, something recognised to UL1059 should be acceptable IMO Regards Charlie Charlie Blackham Sulis Consultants Ltd Tel: +44 (0)7946 624317 Web: https://sulisconsultants.com/ Registered in England and Wales, number 05466247 From: Grasso, Charles <[email protected]> Sent: 18 June 2019 19:49 To: [email protected] Subject: Re: [PSES] Grounding My 2c – You are correct (MOO). Thanks! Charles Grasso W: 303-706-5467 From: Steve Brody [mailto:[email protected]] Sent: Tuesday, June 18, 2019 12:39 PM To: [email protected]<mailto:[email protected]> Subject: [PSES] Grounding This message originated outside of DISH and was sent by: [email protected]<mailto:[email protected]> HI all, I have a client with whom I am having a discussion about grounding for an EN 60204-1 product. The product consists of 3 sub-modules all of which use mains power derived from the first module where the external mains comes into the unit. In the first module the ground from the branch circuit goes to a ground stud, lockwasher and nut, and from there a ground wire goes from the stud to a DIN rail mounted Wago terminal block designed for grounds, as it is green/yellow in color, which is screwless and uses spring pressure to secure the wire in place. Other internal grounds in this module also connect to this block. The second module receives the main ground from the first module in a similar arrangement, and the third module gets it's ground from the second module. I have pointed out to my client that, in accordance with all safety standards I am aware of, and a figure in EN 60204-1 on grounds, that modules 2 and 3 must have ground leads that goes back to the point where the main ground comes into the unit originally, and not daisy chained from module to module. I don't think there is anyone who will disagree with this but I did say I would ask the question. Second question is do you thin there is a problem is using a screwless pressure connector for the grounds, as opposed to a stud/lockwasher/nut? Thoughts and comments would be appreciated by reply to his or privately at [email protected]<https://connect.xfinity.com/appsuite/[email protected]> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe)<http://www.ieee-pses.org/list.html> List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher <[email protected]<mailto:[email protected]>> David Heald <[email protected]<mailto:[email protected]>> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe)<http://www.ieee-pses.org/list.html> List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher <[email protected]<mailto:[email protected]>> David Heald <[email protected]<mailto:[email protected]>> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher: <[email protected]> David Heald: <[email protected]>
