I suppose shaping of the curve corners removes harmonics introduced by the abrupt transitions, allowing an accelerated ramp inbetween. But does this really reduce the total rise time to 2.5ms? It seems that the softening process must take some time. Wish I had a K3 here to scope against other radios. Anything published out there?
Ed / w2rf From: Alan Bloom <[email protected]> Sent: Monday, June 8, 2020 3:15 PM To: E.H. Russell <[email protected]> Cc: 'Elecraft Reflector' <[email protected]> Subject: Re: [Elecraft] CW rise time setting In the "good old days" key shaping was done simply by adding a capacitor to the key line or equivalent. That results in an exponential rise and/or fall time, which is not optimum, so the time constant had to be set pretty slow to avoid key clicks. Typically 5-10 ms. 10 ms results in "mushy" keying, especially at high CW speeds. Raised-cosine key shaping is close to optimum and is easy to implement with a DSP. It allows faster rise/fall times without key clicks. I assume Elecraft is using something like that. Alan N1AL On 2020-06-08 12:51, E.H. Russell wrote: I'm used to CW rise times in th 4-7ms range. Is this 2.5ms arrived at by a different metric? Is the curve added by sigmoidal shaping somehow excluded from the measurement? Ed / w2rf -----Original Message----- From: [email protected] <mailto:[email protected]> <[email protected] <mailto:[email protected]> > On Behalf Of Richard Stutsman Sent: Monday, June 8, 2020 1:31 PM To: David Gilbert <[email protected] <mailto:[email protected]> > Cc: Elecraft Reflector <[email protected] <mailto:[email protected]> > Subject: Re: [Elecraft] CW rise time setting Yes, I would regard a 2.5 msec rise time (using appropriate sigmoid shaping) to probably be ideal, in which case I would have no desire to modify or shorten it. I'll bet it will sound even better than a Drake or a Ten-Tec! I hereby withdraw my previous request/opinion. Rick N6IET On Mon, Jun 8, 2020 at 10:27 AM David Gilbert < <mailto:[email protected] <mailto:[email protected]> > [email protected] <mailto:[email protected]> > wrote: You don't need to generate clicks to have a crisp CW tone. Elecraft uses a pretty much optimally shaped waveform (some version of a cosine function) and if I remember correctly the rise time is only about 2.5 msec, although I could be wrong about that last part. And while you may be careful not to use short rise/fall times when the band is active, in the past there have been folks on the contesting reflector who openly admitted they purposely generate clicks by shortening the rise/fall times to give themselves elbow room. I will always appreciate that Elecraft doesn't give those miscreants the means to pollute the band. 73, Dave AB7E On Mon, Jun 8, 2020 at 9:23 AM Richard Stutsman < <mailto:[email protected] <mailto:[email protected]> > [email protected] <mailto:[email protected]> > wrote: I for one would like to have some control over the rise/fall times. You want the cleanest (narrowest) of CW signals when operating on a crowded band or in a contest - unless you're a rare DX station. Most of my operations are 22wpm rag chews on very uncrowded bands. We're often the only discernible signals on an entire CW band. And conditions are often noisy with deep QSB. Why not allow those of us operating in those circumstances to shorten the rise times a bit, which makes it easier to copy in noisy conditions, when any close-in clicks or thumps aren't going to bother anybody? Copying a 'soft' weak CW signal is like trying to read a 'crisp' signal that's an entire S-unit weaker, IMO. My TS-590sg let's me do that, and I love it! Will the K4 sound as good as a Drake T4C? (Just askin'.) Rick N6IET N4ZR wrote: Will the K4 have options for setting CW rise and fall times...? Hi Pete, Probably not. We've always been very careful to ensure our rigs have an exceptional clean, click-free CW signal. (Third-party testing bears this out.) Minimizing the bandwidth requires a very specific rise/fall time and a hand-crafted sigmoidal shaping function in DSP. Colonel Sanders closely guards his fried chick recipe, Mrs. Fields won't reveal what's in her chocolate-chip cookies, and only selected firmware monks--sworn to secrecy--are privy to Elecraft's keying envelope coefficients :) 73, Wayne N6KR ______________________________________________________________ Elecraft mailing list Home: <http://mailman.qth.net/mailman/listinfo/elecraft> http://mailman.qth.net/mailman/listinfo/elecraft Help: <http://mailman.qth.net/mmfaq.htm> http://mailman.qth.net/mmfaq.htm Post: <mailto:[email protected] <mailto:[email protected]> > mailto:[email protected] <mailto:[email protected]> This list hosted by: <http://www.qsl.net> http://www.qsl.net Please help support this email list: <http://www.qsl.net/donate.html> http://www.qsl.net/donate.html Message delivered to <mailto:[email protected] <mailto:[email protected]> > [email protected] <mailto:[email protected]> ______________________________________________________________ Elecraft mailing list Home: <http://mailman.qth.net/mailman/listinfo/elecraft> http://mailman.qth.net/mailman/listinfo/elecraft Help: <http://mailman.qth.net/mmfaq.htm> http://mailman.qth.net/mmfaq.htm Post: <mailto:[email protected] <mailto:[email protected]> > mailto:[email protected] <mailto:[email protected]> This list hosted by: <http://www.qsl.net> http://www.qsl.net Please help support this email list: <http://www.qsl.net/donate.html> http://www.qsl.net/donate.html Message delivered to <mailto:[email protected] <mailto:[email protected]> > [email protected] <mailto:[email protected]> ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] <mailto:[email protected]> This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected] <mailto:[email protected]> ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]

