I thought the list admin requested ending this string ?? Bob K3DJC On Fri, 15 Mar 2013 08:25:57 -0400 Stephen Roberts <[email protected]> writes: > There is no "A" anywhere indicated on the microphone or base. Preamp > is off and switch is on low impedence. When I plug it in I get a > continuous series if dits and no response from any of the controls > on the unit. > > Steve > W1SFR > > > Sent from my iPad > > On Mar 14, 2013, at 9:44 PM, "Joe Subich, W4TV" <[email protected]> > wrote: > > > > > With a preamp switch on the base, that is an MC-60A. > > > > What position is the slide switch *on the microphone*? That is > the > > switch that determines high vs. low impedance. You want it in > the > > "Low" (500 Ohm) position for the K2 (and K3). There are two > switches > > - the one toward the rear is impedance, the one toward the front > is > > ON/OFF (the microphone element is disconnected in the OFF > position). > > > > If your microphone did not come with a manual, you may want to > download > > a copy from: <http://homepage.ntlworld.com/wadei/MC-60A.pdf> or > > <http://www.n6wk.com/kenwood/MC-60A.pdf> > > > > 73, > > > > ... Joe, W4TV > > > > > > On 3/14/2013 7:15 PM, Mike Flowers wrote: > >> My MC-60 mic says on the bottom by the switch 'mic amp' in/out. > There > >> isn't an 'A' on the Kenwood trim on the front - just MC-60. > Although it > >> may be an MC-60A, there is no visible designation as such. > >> > >> - 73 de Mike, K6MKF, W6NAG, NCDXC, Conway Reef 2012, K3-P3 > Addict, Maui > >> > >> -----Original Message----- > >> From: [email protected] > >> [mailto:[email protected]] On Behalf Of Don > Wilhelm > >> Sent: Thursday, March 14, 2013 4:12 PM > >> To: [email protected] > >> Subject: Re: [Elecraft] Kenwood Mc-60 mic with K2 > >> > >> The MC-60 (not A) schematic that I see on the G4WPW website > indicates that > >> the switch changes from low impedance to high impedance. For use > with the > >> K3 and other modern transceivers the switch should be in the low > impedance > >> position. > >> From the schematic, I cannot understand an "out" label on the > switch. > >> If you have an MC-60A, then "out" would be reasonable referring > to the > >> preamp either in or out. > >> > >> 73, > >> Don W3FPR > >> > >> On 3/14/2013 6:53 PM, Stephen Roberts wrote: > >>> It's a MC-60 and the switch is "Out". > >> > >> ______________________________________________________________ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:[email protected] > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: > http://www.qsl.net/donate.html > >> > >> ______________________________________________________________ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:[email protected] > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: > http://www.qsl.net/donate.html > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: > http://www.qsl.net/donate.html > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected]
This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
