you put enuf downward preassure on the screwdriver and it works
everytime.... and get a good machined set of tools Holy Cow its not a
big block v8!!!!
On 12/27/2012 6:00 PM, [email protected] wrote:
Send Elecraft mailing list submissions to
[email protected]
To subscribe or unsubscribe via the World Wide Web, visit
http://mailman.qth.net/mailman/listinfo/elecraft
or, via email, send a message with subject or body 'help' to
[email protected]
You can reach the person managing the list at
[email protected]
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Elecraft digest..."
Today's Topics:
1. KPA500 PWR Display ([email protected])
2. Re: Problem with a K3 screw - suggestions needed
(Ian White GM3SEK)
3. test ([email protected])
4. Re: New Output Power Issue, and a new question (Richard Fjeld)
5. Re: KPA500 PWR Display (Jack Brindle)
6. Re: KPA500 PWR Display ([email protected])
7. Re: KPA500 PWR Display (Ken K3IU)
8. Fwd: KX3 Micro Manual Available in Apple App Store from
Elecraft Digest, Vol 103, Issue 32 (Jeffrey Blumenfeld)
9. Re: Use of the subject line. (Jim Rhodes)
10. Re: KPA500 PWR Display (Jack Brindle)
11. Re: Problem with a K3 screw - suggestions needed
(Doug Faunt N6TQS +1-510-717-1197)
12. Re: Problem with a K3 screw - suggestions needed (Ken Chandler)
13. Re: KPA500 PWR Display (Ken K3IU)
14. Re: KPA500 PWR Display (Jack Brindle)
15. Re: Fwd: KX3 Micro Manual Available in Apple App Store from
Elecraft Digest, Vol 103, Issue 32 (Mike KS7D)
16. Re: Fwd: KX3 Micro Manual Available in Apple App Store from
Elecraft Digest, Vol 103, Issue 32 (Chip Stratton)
17. Re: KPA500 PWR Display (Ken K3IU)
18. Reflector postings ([email protected])
19. Re: Price guesstimate on KXPA100 (Wayne Burdick)
20. Re: Fwd: KX3 Micro Manual Available in Apple App Store from
Elecraft Digest, Vol 103, Issue 32 (Richard Gillingham)
21. Re: Reflector postings (Don Wilhelm)
22. K3 near salt water (Robert Fanfant)
23. Re: K3 near salt water (W4GRJ)
24. Re: K3 near salt water (Eric Swartz - WA6HHQ, Elecraft)
25. Re: K3 near salt water (Don Wilhelm)
26. Re: K3 near salt water (Ken G Kopp)
27. Re: K3 near salt water (Mike Harris)
28. Long Messages (David Dunn)
29. Rigblaster Plus with Elecraft K3 (Alfredo V?lez WP3C)
30. Re: Long Messages (K2GN)
31. Re: K3 near salt water (W4GRJ)
32. Re: Long Messages (Phil Kane)
----------------------------------------------------------------------
Message: 1
Date: Thu, 27 Dec 2012 12:07:39 -0500 (EST)
From: [email protected]
To: [email protected]
Subject: [Elecraft] KPA500 PWR Display
Message-ID: <[email protected]>
Content-Type: text/plain; charset="US-ASCII"
I like to have the KPA500 display set to constantly show the PWR output.
I just noticed that when I swtich bands from my K3, the KPA500 display
stays set to display PWR output, but when I switch bands on the KPA500, the
display always goes back to display the band. Then I always have to press
PWR again to display the PWR output.
Is there any way to keep the KPA500 display "stuck" on PWR output when
changing bands directly from the KPA500 keypad?
Mike
------------------------------
Message: 2
Date: Thu, 27 Dec 2012 17:21:46 +0000
From: Ian White GM3SEK <[email protected]>
To: [email protected]
Subject: Re: [Elecraft] Problem with a K3 screw - suggestions needed
Message-ID: <[email protected]>
Content-Type: text/plain;charset=us-ascii;format=flowed
In Europe, make sure you are not using a Pozidriv screwdriver.
A Pozidriv #1 screwdriver will kind-of work with the Phillips screws in
the K3... right up to the moment when a screw gets stuck. Beyond that
moment, a Pozidriv screwdriver is very likely to do damage.
Even with a good-quality Phillips #1 driver, my 700-series K3 is now on
its second set of case screws. The originals were worn out by opening up
the K3 to show it to people :-)
73 from Ian GM3SEK
http://www.ifwtech.co.uk/g3sek
Tom H Childers wrote:
Good advice Don.
Another thing that will destroy Phillips head screws is the use of a
reed and prince screw driver, so verify that you are REALY using a
Phillips screw driver.
The very tip of a Phillips screw driver is blunt, not sharp, but a
reed and prince screw driver (which looks very much like a Phillips)
is sharp on the tip and will not seat completely in a Phillips screw,
thus slipping and destroying the socket.
Beware when buying inexpensive screw drivers that are call Phillips
screw drivers. Check the tip and make sure it's not sharp.
73,
Tom
Amateur Radio Operator N5GE
ARRL Lifetime Member
QCWA Lifetime Member
On Wed, 26 Dec 2012 18:15:05 -0500, Don Wilhelm
<[email protected]> wrote:
Fabio,
That screw in into a 2D connector.
You will be able to remove the front panel by removing the other 2
screws in the 2D connector, and then you should be able to rotate the 2D
connector body in a direction that will loosen the screw threads.
Elecraft does have replacement screws. You do not have to purchase the
SS kit, just order by the part number listed in the assembly manual -
you can order one or any multiple you want.
The proper size screwdriver is a #1 Phillips which should be available
worldwide. Do not use a worn Phillips screwdriver, it is certain to
slip and strip out the screwhead. If you have had trouble, I suggest
you invest in a new screwdriver.
I use my #1 Phillips more than most in my Elecraft repair activities,
but if I find my screwdriver does not firmly hold a screw when the
screwdriver shaft is held horizontally, that tip is worn sufficiently
that it should be replaced. I do not want to strip out the screwheads
on my customer's equipment. In other words, do not use worn screwdriver
tips and all should be well.
73,
Don W3FPR
On 12/26/2012 5:46 PM, Fabio IZ4AFW / NZ1W wrote:
Hi guys,
today I decided to try to apply a mod (Audio Low Pass filter) to my
beloved K3.
My K3 was born in September, 2009 and I bought it factory assembled.
Up till now, I just added a couple of additional filters and the KV3A
board; so, I never unassembled the front panel before.
Today I found that one of the upper front panel screws was probably
overtightened (or defective).
I tried to unscrew the screw with several phillips screwdrivers
(little and big), to no avail.
The side effect of my (unsuccessful) tentatives was that:
1) I was not able to unscrew the screw
2) now the screw head is damaged (see pic at
https://picasaweb.google.com/lh/photo/V1aTCoSq5qkgs3y-beE_DdMTjNZETYmy
PJy0liipFm0?feat=directlink)
I got to unassemble the front panel unscrewing a couple of screws
more, but I'd like to solve this little problem (moreover, it's ugly).
Before going with some more destructive methods (I am thinking about
drilling the screw??), I'd like to have some savy suggestion from the
community...
Moreover, do you know if Elecraft has an additional screw kit
available (I don't need the stainless steel ones)?
As a side note, I found that almost all the flat-head screws were very
"soft" and damage-prone (differently from the other round-head screws).
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
