According to the eDP specification (VESA Embedded DisplayPort Standard v1.4b, Section 3.3.10.2), if the value of DP_EDP_PWMGEN_BIT_COUNT is less than DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, the sink is required to use the MIN value as the effective PWM bit count.
This commit updates the logic to clamp the reported DP_EDP_PWMGEN_BIT_COUNT to the range defined by _CAP_MIN and _CAP_MAX. As part of this change, the behavior is modified such that reading both _CAP_MIN and _CAP_MAX registers is now required to succeed, otherwise bl->max value could end up being not set although drm_edp_backlight_probe_max() returned success. This ensures correct handling of eDP panels that report a zero PWM bit count but still provide valid non-zero MIN and MAX capability values. Without this clamping, brightness values may be interpreted incorrectly, leading to a dim or non-functional backlight. For example, the Samsung ATNA40YK20 OLED panel used in the Lenovo ThinkPad T14s Gen6 (Snapdragon) reports a PWM bit count of 0, but supports AUX backlight control and declares a valid 11-bit range. Clamping ensures brightness scaling works as intended on such panels. Co-developed-by: Rui Miguel Silva <rui.si...@linaro.org> Signed-off-by: Rui Miguel Silva <rui.si...@linaro.org> Signed-off-by: Christopher Obbard <christopher.obb...@linaro.org> --- Changes in v6: - Update commit message around chaning reading PWMGEN_BIT_COUNT_CAP_MIN and _CAP_MAX to be required. - Link to v5: https://lore.kernel.org/r/20250330-wip-obbardc-qcom-t14s-oled-panel-brightness-v5-1-25083d973...@linaro.org Changes in v5: - Correctly check return value when reading PWMGEN_BIT_COUNT_CAP_MIN and _CAP_MAX. - Link to v4: https://lore.kernel.org/r/20250330-wip-obbardc-qcom-t14s-oled-panel-brightness-v4-1-85ef0991b...@linaro.org Changes in v4: - Remove unrelated whitespace changes. - Remove unrelated commit change. - Add note to commit message about changing read of PWMGEN_BIT_COUNT_CAP_MIN and _CAP__MAX from optional to required. - Link to v3: https://lore.kernel.org/r/20250330-wip-obbardc-qcom-t14s-oled-panel-brightness-v3-1-156801d97...@linaro.org Changes in v3: - Properly rebase patch on top of latest version of drm-misc-next. - Make patch more generic by clamping PWM bit count to advertised MIN and MAX capabilities (suggested by Dmitry). - Link to v2: https://lore.kernel.org/r/20250327-wip-obbardc-qcom-t14s-oled-panel-brightness-v2-1-16dc3ee00...@linaro.org Changes in v2: - Split backlight brightness patch from T14s OLED enablement series. - Use PWMGEN_CAP_MIN rather than MAX (Dmitry). - Rework commit message to reference eDP spec. - Rebase on drm-misc-next. - Link to v1: https://lore.kernel.org/all/20250325-wip-obbardc-qcom-t14s-oled-panel-v2-4-e9bc7c9d3...@linaro.org/ --- drivers/gpu/drm/display/drm_dp_helper.c | 42 +++++++++++++++++++++------------ 1 file changed, 27 insertions(+), 15 deletions(-) diff --git a/drivers/gpu/drm/display/drm_dp_helper.c b/drivers/gpu/drm/display/drm_dp_helper.c index e2439c8a7fefe116b04aaa689b557e2387b05540..5550c40310c55ee275b3ebec08a7500cab38ae78 100644 --- a/drivers/gpu/drm/display/drm_dp_helper.c +++ b/drivers/gpu/drm/display/drm_dp_helper.c @@ -28,6 +28,7 @@ #include <linux/init.h> #include <linux/iopoll.h> #include <linux/kernel.h> +#include <linux/minmax.h> #include <linux/module.h> #include <linux/sched.h> #include <linux/seq_file.h> @@ -4035,6 +4036,32 @@ drm_edp_backlight_probe_max(struct drm_dp_aux *aux, struct drm_edp_backlight_inf } pn &= DP_EDP_PWMGEN_BIT_COUNT_MASK; + + ret = drm_dp_dpcd_read_byte(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min); + if (ret < 0) { + drm_dbg_kms(aux->drm_dev, "%s: Failed to read pwmgen bit count cap min: %d\n", + aux->name, ret); + return -ENODEV; + } + pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK; + + ret = drm_dp_dpcd_read_byte(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max); + if (ret < 0) { + drm_dbg_kms(aux->drm_dev, "%s: Failed to read pwmgen bit count cap max: %d\n", + aux->name, ret); + return -ENODEV; + } + pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK; + + /* + * Per VESA eDP Spec v1.4b, section 3.3.10.2: + * If DP_EDP_PWMGEN_BIT_COUNT is less than DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, + * the sink must use the MIN value as the effective PWM bit count. + * Clamp the reported value to the [MIN, MAX] capability range to ensure + * correct brightness scaling on compliant eDP panels. + */ + pn = clamp(pn, pn_min, pn_max); + bl->max = (1 << pn) - 1; if (!driver_pwm_freq_hz) return 0; @@ -4061,21 +4088,6 @@ drm_edp_backlight_probe_max(struct drm_dp_aux *aux, struct drm_edp_backlight_inf * - FxP is within 25% of desired value. * Note: 25% is arbitrary value and may need some tweak. */ - ret = drm_dp_dpcd_read_byte(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min); - if (ret < 0) { - drm_dbg_kms(aux->drm_dev, "%s: Failed to read pwmgen bit count cap min: %d\n", - aux->name, ret); - return 0; - } - ret = drm_dp_dpcd_read_byte(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max); - if (ret < 0) { - drm_dbg_kms(aux->drm_dev, "%s: Failed to read pwmgen bit count cap max: %d\n", - aux->name, ret); - return 0; - } - pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK; - pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK; - /* Ensure frequency is within 25% of desired value */ fxp_min = DIV_ROUND_CLOSEST(fxp * 3, 4); fxp_max = DIV_ROUND_CLOSEST(fxp * 5, 4); --- base-commit: 4c4d9b7b6c6e676eca22585139aba5f03de74b90 change-id: 20250327-wip-obbardc-qcom-t14s-oled-panel-brightness-4020865b6580 Best regards, -- Christopher Obbard <christopher.obb...@linaro.org>
