Hi folks,
I'm trying to write a simple script to generate a packet into an existing
ovs interface (below). Instead of using "ovs-appctl ofproto/trace", I'm
attempting "ovs-appctl netdev-dummy/receive" so I can generate the raw
bytes, similar to what we have in the AT tests.
Is "netdev-dummy/receive" something that did not exist in 2.0.2?
Any pointers on how one could use that functionality?
Maybe I could do this from an ovs sandbox?
Thanks,
-- flaviof
---
[dell:ovsScripts.git] (master)$ lsmod | grep dummy
dummy 16384 0
[dell:ovsScripts.git] (master)$
[dell:ovsScripts.git] (master)$ sudo ovs-vsctl show
c0006a18-e32c-44aa-9985-7641d61a74fc
Bridge brtest
Port brtest
Interface brtest
type: internal
Port "dummy0"
Interface "dummy0"
ovs_version: "2.0.2"
[dell:ovsScripts.git] (master)$
[dell:ovsScripts.git] (master)$ ip a s dev dummy0
13: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master
ovs-system state UNKNOWN group default
link/ether 00:01:02:03:04:05 brd ff:ff:ff:ff:ff:ff
inet 192.168.55.254/24 scope global dummy0
valid_lft forever preferred_lft forever
inet6 fe80::d074:13ff:fe2f:26d3/64 scope link
valid_lft forever preferred_lft forever
[dell:ovsScripts.git] (master)$
[dell:ovsScripts.git] (master)$
[dell:ovsScripts.git] (master)$ cat sendIcmp.sh
#!/bin/bash
ip_to_hex() {
printf "%02x%02x%02x%02x" "$@"
}
test_ipv4_icmp_request() {
local invif=$1 eth_src=$2 eth_dst=$3 ipv4_src=$4 ipv4_dst=$5
icmpv4_code=$6
shift; shift; shift; shift; shift; shift
# This packet has bad checksums but logical L3 routing doesn't check.
local hdrchksum=0000
local icmp_seq=0001
local icmp_ts=02bb445700000000 ; # May/24/16 16:35:14 EDT
local
icmp_data=000102030405060708090001020304050607080900010203040506070809000102030405060708090001020304050607
; # 48 bytes
local icmp_payload=0800${hdrchksum}5fbf${icmp_seq}${icmp_ts}${icmp_data}
local
packet=${eth_dst}${eth_src}080045000054000040004001${hdrchksum}${ipv4_src}${ipv4_dst}0035111100080000${icmp_payload}
sudo ovs-appctl netdev-dummy/receive $invif $packet
}
eth_dst=000102030405
eth_src=001122334455
ip_src=$(ip_to_hex 192 168 50 33)
ip_dst=$(ip_to_hex 192 168 55 254)
set -x
test_ipv4_icmp_request dummy0 $eth_src $eth_dst $ip_src $ip_dst
echo ok
[dell:ovsScripts.git] (master)$
[dell:ovsScripts.git] (master)$ ./sendIcmp.sh
+ test_ipv4_icmp_request dummy0 001122334455 000102030405 c0a83221 c0a837fe
+ local invif=dummy0 eth_src=001122334455 eth_dst=000102030405
ipv4_src=c0a83221 ipv4_dst=c0a837fe icmpv4_code=
+ local hdrchksum=0000
+ local icmp_seq=0001
+ local icmp_ts=02bb445700000000
+ local
icmp_data=000102030405060708090001020304050607080900010203040506070809000102030405060708090001020304050607
+ local
icmp_payload=080000005fbf000102bb445700000000000102030405060708090001020304050607080900010203040506070809000102030405060708090001020304050607
+ local
packet=0001020304050011223344550800450000540000400040010000c0a83221c0a837fe0035111100080000080000005fbf000102bb445700000000000102030405060708090001020304050607080900010203040506070809000102030405060708090001020304050607
+ sudo ovs-appctl netdev-dummy/receive dummy0
0001020304050011223344550800450000540000400040010000c0a83221c0a837fe0035111100080000080000005fbf000102bb445700000000000102030405060708090001020304050607080900010203040506070809000102030405060708090001020304050607
"netdev-dummy/receive" is not a valid command
ovs-appctl: ovs-vswitchd: server returned an error
+ echo ok
ok
[dell:ovsScripts.git] (master)$
_______________________________________________
discuss mailing list
discuss@openvswitch.org
http://openvswitch.org/mailman/listinfo/discuss
