Thanks Jesse, I solved this issue through upgrade the NIC driver igb from 2.1 to 2.4, now it is ok even if use Linux bond as the external port of ovs bridge. And i will try to use OVS bonding once i have a chance. Also i hope FAQ can list which NIC driver has vlan problem, and should be upgrade to which version.
Thanks, Kris On Thu, May 30, 2013 at 7:22 AM, Jesse Gross <[email protected]> wrote: > Linux bonds don't pass vlan information through to the driver. If you > use OVS bonding then you shouldn't have this problem. > > On Wed, May 29, 2013 at 11:08 AM, Kris zhang <[email protected]> wrote: > > I found the reason, the problem is not caused by vlan splinters, it > caused > > by bond0. I don't know why, but if remove the bond0, and ovs-br0 directly > > connect to eth0, the problem disappears. > > > > > > > > > > On Mon, May 27, 2013 at 10:10 AM, Kris zhang <[email protected]> > wrote: > >> > >> Hi Jesse, > >> > >> Because if i don't use the vlan splinters, the VMs' network traffic will > >> be nearly 0 M/s (but they can ping each other). I read FAQ, it says the > >> reason maybe the NIC driver or Linux kernel version problems, and it > also > >> says the vlan splinters may solve this issue, but they don't said the > ping > >> will miss some packets when add a new vlan. is it a bug for vlan > splinters? > >> Please see the images in the attachment. > >> > >> Thanks, > >> Kris > >> > >> > >> On Thu, May 23, 2013 at 11:25 PM, Jesse Gross <[email protected]> wrote: > >>> > >>> It seems that the original issue was that you were using VLANs when > >>> you shouldn't have. In that case, why are you trying to use VLAN > >>> splinters? > >>> > >>> On Thu, May 23, 2013 at 2:44 AM, Kris zhang <[email protected]> > wrote: > >>> > Thanks Jesse, but i still cannot fix my issue. Because if i use vlan > >>> > splinters, the above issue will be happened, if i don't use vlan > >>> > splinters, > >>> > the packets between the VMs are very slow (ping is ok), i use > ovs-dpctl > >>> > dump-flows br0, get the following result: > >>> > > >>> > > >>> > > in_port(1),eth(src=c6:b0:ea:37:29:47,dst=c6:b0:3a:c0:0d:55),eth_type(0x8100),vlan(vid=3000,pcp=0),encap(eth_type(0x0800),ipv4(src=20.1.120.12,dst=20.1.120.13,proto=1,tos=1,ttl=64,frag=no),icmp(type=8,code=0)), > >>> > packets:101, bytes:10302, used:4.341s, actions=pop_vlan,3 > >>> > > >>> > > in_port(3),eth(src=c6:b0:3a:c0:0d:55,dst=c6:b0:ea:37:29:47),eth_type(0x0800),ipv4(src=20.1.120.13,dst=20.1.120.12,proto=1,tos=0,ttl=64,frag=no),icmp(type=0,code=0)), > >>> > packets:101, bytes:9898, used:4.341s, > >>> > actions=push_vlan(vid=3000,pcp=0),1 > >>> > > >>> > The port 1 is eth1, and the port 3 is the tap of VM. > >>> > Does the iptables affect the ovs? If not, i have to upgrade the linux > >>> > kernel, or upgrade NIC driver. > >>> > > >>> > Thanks, > >>> > Kris > >>> > > >>> > > >>> > > >>> > > >>> > On Tue, May 21, 2013 at 3:32 AM, Jesse Gross <[email protected]> > wrote: > >>> >> > >>> >> There's an extensive section in the FAQ about vlans that I would > >>> >> recommend reading. > >>> >> > >>> >> On Mon, May 20, 2013 at 8:51 AM, Kris zhang <[email protected]> > >>> >> wrote: > >>> >> > No, so you mean it maybe not caused by vlan splinters? > >>> >> > > >>> >> > > >>> >> > On Mon, May 20, 2013 at 11:18 PM, Jesse Gross <[email protected]> > >>> >> > wrote: > >>> >> >> > >>> >> >> On Mon, May 20, 2013 at 4:37 AM, Kris zhang < > [email protected]> > >>> >> >> wrote: > >>> >> >> > Hi guys, > >>> >> >> > > >>> >> >> > I use ovs-1.7.1, and i run ovs on a single NIC host (CentOS): > >>> >> >> > > >>> >> >> > # ovs-vsctl add-br br0 > >>> >> >> > # ovs-vsctl add-port br0 eth0 > >>> >> >> > > >>> >> >> > Then i setup the eth0 interface's other_config: > >>> >> >> > enable-vlan-splinters="true". > >>> >> >> > > >>> >> >> > Last I ping this host by another PC, and at same time i do > this: > >>> >> >> > > >>> >> >> > # ovs-vsctl add-port taptest br0 tag=100 > >>> >> >> > > >>> >> >> > I found there are 4 "Request timed out." happened. That means > the > >>> >> >> > host > >>> >> >> > lost > >>> >> >> > connect about 4 seconds. > >>> >> >> > > >>> >> >> > If i remove the vlan splinters on interface eth0. it won't > >>> >> >> > happen. > >>> >> >> > So does anybody know the reason? > >>> >> >> > >>> >> >> Is the other machine actually on that VLAN? > >>> >> > > >>> >> > > >>> > > >>> > > >> > >> > > >
_______________________________________________ discuss mailing list [email protected] http://openvswitch.org/mailman/listinfo/discuss
