*From:*discuss-gnuradio-bounces+ssaluja=princeton....@gnu.org
[mailto:discuss-gnuradio-bounces+ssaluja=princeton....@gnu.org] *On
Behalf Of * Marcus Müller
*Sent:* Wednesday, November 18, 2015 6:09 PM
*To:* discuss-gnuradio@gnu.org
*Subject:* Re: [Discuss-gnuradio] Gnuradio-companion
Dear Sumit.
I just noticed this thread:
you're using RHEL 6, which only hast Boost 1.41; UHD cannot build with
anything below Boost 1.46.
Is there a particular reason for sticking with this very old version,
or can you upgrade to RHEL7 or CentOS7?
Best regards,
Marcus
On 18.11.2015 23:43, Sumit Saluja wrote:
Please see the logs with -v option
./build-gnuradio -v
This script will install Gnu Radio from current GIT sources
You will require Internet access from the computer on which this
script runs. You will also require SUDO access. You will require
approximately 500MB of free disk space to perform the build.
This script will, as a side-effect, remove any existing Gnu Radio
installation that was installed from your Linux distribution packages.
It must do this to prevent problems due to interference between
a linux-distribution-installed Gnu Radio/UHD and one installed
from GIT source.
The whole process may take up to two hours to complete, depending
on the
capabilities of your system.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
NOTE: if you run into problems while running this script, you can
re-run it with
the --verbose option to produce lots of diagnostic output to help
debug problems.
This script has been written to anticipate some of the more common
problems one might
encounter building ANY large, complex software package. But it is
not pefect, and
there are certainly some situations it could encounter that it
cannot deal with
gracefully. Altering the system configuration from something
reasonably standard,
removing parts of the filesystem, moving system libraries around
arbitrarily, etc,
it likely cannot cope with. It is just a script. It isn't
intuitive or artificially
intelligent. It tries to make life a little easier for you, but at
the end of the day
if it runs into trouble, a certain amount of knowledge on your
part about
system configuration and idiosyncrasies will inevitably be necessary.
Proceed?yes
Starting all functions at: Wed Nov 18 17:38:05 EST 2015
SUDO privileges are required
Do you have SUDO privileges?yes
Continuing with script
./build-gnuradio: line 1410: [: 90
90
90
90
90
90
90
90
90
90: integer expression expected
Installing prerequisites.
====> THIS MAY TAKE QUITE SOME TIME <=====
Loaded plugins: refresh-packagekit, security
Setting up Remove Process
No Match for argument: gnuradio*
No Packages marked for removal
Loaded plugins: refresh-packagekit, security
Setting up Remove Process
No Match for argument: libgruel-*
No Packages marked for removal
Loaded plugins: refresh-packagekit, security
Setting up Remove Process
No Match for argument: libgruel*
No Packages marked for removal
Loaded plugins: refresh-packagekit, security
Setting up Group Process
Warning: Group Engineering and Scientific does not exist.
Package flex-2.5.35-9.el6.x86_64 already installed and latest version
Package gcc-4.4.7-16.el6.x86_64 already installed and latest version
Package redhat-rpm-config-9.0.3-44.sl6.noarch already installed
and latest version
Package rpm-build-4.8.0-47.el6.x86_64 already installed and latest
version
Package 1:make-3.81-20.el6.x86_64 already installed and latest
version
Package patch-2.6-6.el6.x86_64 already installed and latest version
Package 1:pkgconfig-0.23-9.1.el6.x86_64 already installed and
latest version
Package gettext-0.17-18.el6.x86_64 already installed and latest
version
Package automake-1.11.1-4.el6.noarch already installed and latest
version
Package bison-2.4.1-5.el6.x86_64 already installed and latest version
Package flex-devel-2.5.35-9.el6.x86_64 already installed and
latest version
Package libtool-2.2.6-15.5.el6.x86_64 already installed and latest
version
Package autoconf-2.63-5.1.el6.noarch already installed and latest
version
Package gcc-c++-4.4.7-16.el6.x86_64 already installed and latest
version
Package binutils-2.20.51.0.2-5.43.el6.x86_64 already installed and
latest version
Package patchutils-0.3.1-3.1.el6.x86_64 already installed and
latest version
Package byacc-1.9.20070509-7.el6.x86_64 already installed and
latest version
Package indent-2.2.10-7.el6.x86_64 already installed and latest
version
Package systemtap-2.7-2.el6.x86_64 already installed and latest
version
Package diffstat-1.51-2.el6.x86_64 already installed and latest
version
Package elfutils-0.161-3.el6.x86_64 already installed and latest
version
Package cvs-1.11.23-16.el6.x86_64 already installed and latest
version
Package rcs-5.7-37.el6.x86_64 already installed and latest version
Package subversion-1.6.11-15.el6_7.x86_64 already installed and
latest version
Package gcc-gfortran-4.4.7-16.el6.x86_64 already installed and
latest version
Package 1:doxygen-1.6.1-6.el6.x86_64 already installed and latest
version
Package intltool-0.41.0-1.1.el6.noarch already installed and
latest version
Package git-1.8.3.1-1.sdl6.x86_64 already installed and latest
version
Package ctags-5.8-2.el6.x86_64 already installed and latest version
Package cscope-15.6-6.el6.x86_64 already installed and latest version
Package swig-1.3.40-6.el6.x86_64 already installed and latest version
Warning: Group development does not have any packages.
No packages in any requested group available to install or update
Loaded plugins: refresh-packagekit, security
Setting up Install Process
Package fftw-devel-3.2.1-3.1.el6.x86_64 already installed and
latest version
Package cppunit-devel-1.12.1-3.1.el6.x86_64 already installed and
latest version
Package wxPython-devel-2.8.12.0-1.puias6.x86_64 already installed
and latest version
Package libusb-devel-0.1.12-23.el6.x86_64 already installed and
latest version
Package boost-devel-1.41.0-27.el6.x86_64 already installed and
latest version
Package alsa-lib-devel-1.0.22-3.el6.x86_64 already installed and
latest version
Package 1:numpy-1.6.2-0.1.puias6.x86_64 already installed and
latest version
Package gsl-devel-1.13-1.el6.x86_64 already installed and latest
version
Package python-devel-2.6.6-64.el6.x86_64 already installed and
latest version
No package pygsl available.
Package python-cheetah-2.4.1-1.el6.x86_64 already installed and
latest version
Package python-mako-0.3.4-1.el6.noarch already installed and
latest version
Package python-lxml-2.2.3-1.1.el6.x86_64 already installed and
latest version
Package PyOpenGL-3.0.0-2.1.el6.noarch already installed and latest
version
Package 1:qt-devel-4.6.2-28.el6_5.x86_64 already installed and
latest version
Package 1:qt-4.6.2-28.el6_5.x86_64 already installed and latest
version
Package 1:qt-4.6.2-28.el6_5.x86_64 already installed and latest
version
Package 1:qt-devel-4.6.2-28.el6_5.x86_64 already installed and
latest version
Package PyQt4-devel-4.6.2-9.el6.x86_64 already installed and
latest version
Package qwt-devel-5.1.1-4.1.el6.x86_64 already installed and
latest version
Package qwtplot3d-qt4-devel-0.2.7-9.el6.x86_64 already installed
and latest version
Package libusb-0.1.12-23.el6.x86_64 already installed and latest
version
Package libusb-devel-0.1.12-23.el6.x86_64 already installed and
latest version
Package libusb1-1.0.9-0.6.rc1.el6.x86_64 already installed and
latest version
Package libusb1-devel-1.0.9-0.6.rc1.el6.x86_64 already installed
and latest version
Package cmake-2.8.12.2-4.el6.x86_64 already installed and latest
version
Package git-1.8.3.1-1.sdl6.x86_64 already installed and latest
version
Package wget-1.12-5.el6_6.1.x86_64 already installed and latest
version
Package python-docutils-0.6-1.el6.noarch already installed and
latest version
Package PyQwt-5.2.0-11.puias6.x86_64 already installed and latest
version
Package PyQwt-devel-5.2.0-11.puias6.x86_64 already installed and
latest version
Package qwt-devel-5.1.1-4.1.el6.x86_64 already installed and
latest version
Package gtk2-engines-2.18.4-5.el6.x86_64 already installed and
latest version
Package xmlrpc-c-client-1.16.24-1210.1840.el6.x86_64 already
installed and latest version
Package xmlrpc-c-c++-1.16.24-1210.1840.el6.x86_64 already
installed and latest version
Package xmlrpc-c-devel-1.16.24-1210.1840.el6.x86_64 already
installed and latest version
Package xmlrpc-c-apps-1.16.24-1210.1840.el6.x86_64 already
installed and latest version
Package xmlrpc-c-1.16.24-1210.1840.el6.x86_64 already installed
and latest version
Package xmlrpc-c-client++-1.16.24-1210.1840.el6.x86_64 already
installed and latest version
No package libzmq available.
No package libzmq-dev available.
Package tkinter-2.6.6-64.el6.x86_64 already installed and latest
version
Package orc-0.4.16-6.el6.x86_64 already installed and latest version
Package python-requests-2.6.0-3.el6.noarch already installed and
latest version
Nothing to do
Checking for library libusb ...Found library libusb
Checking for library libboost ...Found library libboost
Checking for library libcppunit ...Found library libcppunit
Checking for library libfftw ...Found library libfftw
Checking for library libgsl ...Found library libgsl
Done
This script will fetch Gnu Radio version 3.7/maint from the
repositories, along with compatible
extras.
Is this OK?yes
Fetching various packages (Gnu Radio, UHD, gr-osmosdr, gr-iqbal, etc)
via the Internet
=======> THIS MAY TAKE QUITE SOME TIME <=========
Fetching Gnu Radio via GIT...Cloning into 'gnuradio'...
Submodule 'volk' (https://github.com/gnuradio/volk.git) registered
for path 'volk'
Cloning into 'volk'...
remote: Counting objects: 5589, done.
remote: Total 5589 (delta 0), reused 0 (delta 0), pack-reused 5589
Receiving objects: 100% (5589/5589), 1.58 MiB | 266.00 KiB/s, done.
Resolving deltas: 100% (3997/3997), done.
Submodule path 'volk': checked out
'f0b722392950bf7ede7b32f5ff60019bce7a8592'
M volk
Branch maint set up to track remote branch maint from origin.
Switched to a new branch 'maint'
Done
Fetching UHD via GIT...Cloning into 'uhd'...
remote: Counting objects: 53257, done.
remote: Compressing objects: 100% (33/33), done.
remote: Total 53257 (delta 4), reused 0 (delta 0), pack-reused 53224
Receiving objects: 100% (53257/53257), 96.50 MiB | 1.25 MiB/s, done.
Resolving deltas: 100% (40626/40626), done.
Fetching rtl-sdr (rtl-sdr, gr-osmosdr, gr-iqbal, hackrf, bladeRF
and airspy) via GIT
Cloning into 'rtl-sdr'...
remote: Counting objects: 1617, done.
remote: Compressing objects: 100% (711/711), done.
remote: Total 1617 (delta 1182), reused 1213 (delta 898)
Receiving objects: 100% (1617/1617), 345.89 KiB | 529.00 KiB/s, done.
Resolving deltas: 100% (1182/1182), done.
Cloning into 'gr-osmosdr'...
remote: Counting objects: 3818, done.
remote: Compressing objects: 100% (2510/2510), done.
remote: Total 3818 (delta 2737), reused 1886 (delta 1270)
Receiving objects: 100% (3818/3818), 925.99 KiB | 876.00 KiB/s, done.
Resolving deltas: 100% (2737/2737), done.
Cloning into 'gr-iqbal'...
remote: Counting objects: 219, done.
remote: Compressing objects: 100% (175/175), done.
remote: Total 219 (delta 109), reused 98 (delta 40)
Receiving objects: 100% (219/219), 130.17 KiB | 0 bytes/s, done.
Resolving deltas: 100% (109/109), done.
Cloning into 'bladeRF'...
remote: Counting objects: 16325, done.
remote: Total 16325 (delta 0), reused 0 (delta 0), pack-reused 16325
Receiving objects: 100% (16325/16325), 6.81 MiB | 1.37 MiB/s, done.
Resolving deltas: 100% (9380/9380), done.
Submodule 'libosmo-dsp' (git://git.osmocom.org/libosmo-dsp)
registered for path 'libosmo-dsp'
Cloning into 'libosmo-dsp'...
remote: Counting objects: 172, done.
remote: Compressing objects: 100% (106/106), done.
remote: Total 172 (delta 89), reused 123 (delta 58)
Receiving objects: 100% (172/172), 60.12 KiB | 0 bytes/s, done.
Resolving deltas: 100% (89/89), done.
Submodule path 'libosmo-dsp': checked out
'f9df8894c72cbd491bdd2f6d4cbea95c46810267'
Cloning into 'hackrf'...
remote: Counting objects: 9629, done.
remote: Total 9629 (delta 0), reused 0 (delta 0), pack-reused 9629
Receiving objects: 100% (9629/9629), 24.49 MiB | 21.42 MiB/s, done.
Resolving deltas: 100% (6741/6741), done.
Cloning into 'host'...
remote: Counting objects: 626, done.
remote: Total 626 (delta 0), reused 0 (delta 0), pack-reused 626
Receiving objects: 100% (626/626), 587.24 KiB | 0 bytes/s, done.
Resolving deltas: 100% (452/452), done.
Done
Starting function uhd_build at: Wed Nov 18 17:41:12 EST 2015
Building UHD...
=============> THIS WILL TAKE SOME TIME <=============
-- The CXX compiler identification is GNU 4.4.7
-- The C compiler identification is GNU 4.4.7
-- Check for working CXX compiler: /usr/bin/c++
-- Check for working CXX compiler: /usr/bin/c++ -- works
-- Detecting CXX compiler ABI info
-- Detecting CXX compiler ABI info - done
-- Check for working C compiler: /usr/bin/cc
-- Check for working C compiler: /usr/bin/cc -- works
-- Detecting C compiler ABI info
-- Detecting C compiler ABI info - done
--
-- Configuring the python interpreter...
-- Found PythonInterp: /usr/lib/python2.7/bin/python (found
version "2.7.8")
-- Python interpreter: /usr/lib/python2.7/bin/python
-- Override with: -DPYTHON_EXECUTABLE=<path-to-python>
-- Using UHD Images Directory: OFF
-- Build type not specified: defaulting to release.
-- Performing Test HAVE_VISIBILITY_HIDDEN
-- Performing Test HAVE_VISIBILITY_HIDDEN - Success
-- Performing Test HAVE_VISIBILITY_INLINES_HIDDEN
-- Performing Test HAVE_VISIBILITY_INLINES_HIDDEN - Success
--
-- Configuring Boost C++ Libraries...
-- Could NOT find Boost
-- Boost include directories: /usr/include
-- Boost library directories: /usr/lib64
-- Boost libraries:
-- Looking for log2
-- Looking for log2 - found
--
-- Python checking for Python version 2.6 or greater
-- Python checking for Python version 2.6 or greater - found
--
-- Python checking for Mako templates 0.4 or greater
-- Python checking for Mako templates 0.4 or greater - found
--
-- Configuring LibUHD support...
-- Dependency Boost_FOUND = 0
-- Dependency HAVE_PYTHON_PLAT_MIN_VERSION = TRUE
-- Dependency HAVE_PYTHON_MODULE_MAKO = TRUE
CMake Error at cmake/Modules/UHDComponent.cmake:51 (MESSAGE):
Dependencies for required component LibUHD not met.
Call Stack (most recent call first):
CMakeLists.txt:279 (LIBUHD_REGISTER_COMPONENT)
-- Configuring incomplete, errors occurred!
See also
"/home/ssaluja/test/uhd/host/build/CMakeFiles/CMakeOutput.log".
make: *** No rule to make target `clean'. Stop.
make: *** No targets specified and no makefile found. Stop.
UHD build apparently failed
Exiting UHD build
=======================================================================
If you have found this script useful and time-saving, consider a
donation to help me keep build-gnuradio, simple_ra, SIDsuite,
meteor_detector, simple_fm_rcv, and multimode maintained and up to
date.
A simple paypal transfer to mle...@ripnet.com
<mailto:mle...@ripnet.com> is all you need to do.
======================================================================
Send success/fail info to sbrac.org?
------------------------------------------------------------------------
*From:*discuss-gnuradio-bounces+ssaluja=princeton....@gnu.org
<mailto:discuss-gnuradio-bounces+ssaluja=princeton....@gnu.org>
[discuss-gnuradio-bounces+ssaluja=princeton....@gnu.org
<mailto:discuss-gnuradio-bounces+ssaluja=princeton....@gnu.org>]
on behalf of Marcus D. Leech [mle...@ripnet.com
<mailto:mle...@ripnet.com>]
*Sent:* Wednesday, November 18, 2015 3:58 PM
*To:* discuss-gnuradio@gnu.org <mailto:discuss-gnuradio@gnu.org>
*Subject:* Re: [Discuss-gnuradio] Gnuradio-companion
On 11/18/2015 03:45 PM, Sumit Saluja wrote:
If I am building gnuradio manually Iam getting following message
######################################################
-- # Gnuradio disabled components
-- ######################################################
-- * gr-ctrlport
-- * gnuradio-companion
-- * gr-comedi
-- * gr-uhd
-- * gr-video-sdl
-- * gr-wxgui
-- * gr-zeromq
If I am building Gnuradio using build-gnuradio script then
getting following error
====> THIS MAY TAKE QUITE SOME TIME <=====
Checking for library libusb ...Found library libusb
Checking for library libboost ...Found library libboost
Checking for library libcppunit ...Found library libcppunit
Checking for library libfftw ...Found library libfftw
Checking for library libgsl ...Found library libgsl
Done
This script will fetch Gnu Radio version 3.7/maint from the
repositories, along with compatible
extras.
Is this OK?yes
Fetching various packages (Gnu Radio, UHD, gr-osmosdr,
gr-iqbal, etc)
via the Internet
=======> THIS MAY TAKE QUITE SOME TIME <=========
Fetching Gnu Radio via GIT...Done
Fetching UHD via GIT...Fetching rtl-sdr (rtl-sdr, gr-osmosdr,
gr-iqbal, hackrf, bladeRF and airspy) via GIT
Done
Starting function uhd_build at: Wed Nov 18 15:44:13 EST 2015
Building UHD...
=============> THIS WILL TAKE SOME TIME <=============
UHD build apparently failed
Exiting UHD build
Thanks
Sumit Saluja
If you run build-gnuradio with -v, you'll get more logs, and
likely a note from Cmake that it couldn't find some depend that
gnuradio-companion relies on.
------------------------------------------------------------------------
*From:*18740449846 [18740449...@163.com <mailto:18740449...@163.com>]
*Sent:* Monday, November 16, 2015 7:56 PM
*To:* Sumit Saluja
*Subject:* »Ø¸´: [Discuss-gnuradio] Gnuradio-companion
hi
you need give some detail
for example
how do you build the gnuradio-companion and is you conmmand work
well show us the result
this is useful to solve you problem
-----From Ekko
-------- ÔʼÓʼþ --------
Ö÷Ì⣺[Discuss-gnuradio] Gnuradio-companion
·¢¼þÈË£ºSumit Saluja
ÊÕ¼þÈË£ºdiscuss-gnuradio@gnu.org <mailto:discuss-gnuradio@gnu.org>
³ËÍ£º
Hi,
I am building gnuradio on RHEL 6 and gnuradio-companion is not
enabling . How I Should enable gnuradio-companion
And UHD is not compiling on RHEL6.
Thanks
Sumit Saluja
_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org <mailto:Discuss-gnuradio@gnu.org>
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org <mailto:Discuss-gnuradio@gnu.org>
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
