Now, I have done complete new installation of Fedora-13, and installed
all the dependencies as mentioned in build guide. After that i have
run git and cloned gnuradio to get latest source. after that i have run
# ./bootstrap
# ./configure
# make
# make check
# sudo make install
I have collected logs from terminal after i ran "make" and have
attached file for your reference. I saw some warnings at last few lines.
after installing gnuradio i went and checked
usrp_dbid.dat and found these lines
"WBX NG TX" 0x0052
"WBX NG RX" 0x0053
and then i checked usrp_dbid.h and found these lines
#define USRP_DBID_WBX_NG_TX 0x0052
#define USRP_DBID_WBX_NG_RX 0x0053
and at last i checked usrp_dbid.py in usrpm folder and found following
lines
#
# Machine generated by gen_usrp_dbid.py from usrp_dbid.dat
# Do not edit by hand. All edits will be overwritten.
#
#
# USRP Daughterboard ID's
#
BASIC_TX = 0x0000
BASIC_RX = 0x0001
DBS_RX = 0x0002
TV_RX = 0x0003
FLEX_400_RX = 0x0004
FLEX_900_RX = 0x0005
FLEX_1200_RX = 0x0006
FLEX_2400_RX = 0x0007
FLEX_400_TX = 0x0008
FLEX_900_TX = 0x0009
FLEX_1200_TX = 0x000a
FLEX_2400_TX = 0x000b
TV_RX_REV_2 = 0x000c
DBS_RX_CLKMOD = 0x000d
LF_TX = 0x000e
LF_RX = 0x000f
FLEX_400_RX_MIMO_A = 0x0014
FLEX_900_RX_MIMO_A = 0x0015
FLEX_1200_RX_MIMO_A = 0x0016
FLEX_2400_RX_MIMO_A = 0x0017
FLEX_400_TX_MIMO_A = 0x0018
FLEX_900_TX_MIMO_A = 0x0019
FLEX_1200_TX_MIMO_A = 0x001a
FLEX_2400_TX_MIMO_A = 0x001b
FLEX_400_RX_MIMO_B = 0x0024
FLEX_900_RX_MIMO_B = 0x0025
FLEX_1200_RX_MIMO_B = 0x0026
FLEX_2400_RX_MIMO_B = 0x0027
FLEX_400_TX_MIMO_B = 0x0028
FLEX_900_TX_MIMO_B = 0x0029
FLEX_1200_TX_MIMO_B = 0x002a
FLEX_2400_TX_MIMO_B = 0x002b
FLEX_1800_RX = 0x0030
FLEX_1800_TX = 0x0031
FLEX_1800_RX_MIMO_A = 0x0032
FLEX_1800_TX_MIMO_A = 0x0033
FLEX_1800_RX_MIMO_B = 0x0034
FLEX_1800_TX_MIMO_B = 0x0035
TV_RX_REV_3 = 0x0040
DTT754 = 0x0041
DTT768 = 0x0042
WBX_LO_TX = 0x0050
WBX_LO_RX = 0x0051
XCVR2450_TX = 0x0060
XCVR2450_RX = 0x0061
EXPERIMENTAL_TX = 0xfffe
EXPERIMENTAL_RX = 0xffff
Can you please tell me why these following daughterboard ID's are
missing in usrp_dbid.py.
"TV Rx MIMO" 0x0043
"TV Rx Rev 2 MIMO" 0x0044
"TV Rx Rev 3 MIMO" 0x0045
"WBX NG TX" 0x0052
"WBX NG RX" 0x0053
"Bitshark Rx" 0x0070
Regards
sanjay
On Fri, Dec 3, 2010 at 2:18 AM, Jason Abele <ja...@ettus.com
<mailto:ja...@ettus.com>> wrote:
On Thu, Dec 2, 2010 at 9:03 AM, Sanjay Singh
<sanjaysinghshyam...@gmail.com
<mailto:sanjaysinghshyam...@gmail.com>> wrote:
> I have done complete new installation of Ubuntu 9.04 Jaunty and
installed
> Binary packege of GNURADIO(3.2.2).
> Can any one tell me why wbx_ng daughterbord ID is missing.
>
Because GNUradio 3.2.2 was released before the WBX ... you will need
to get at least 3.3.0 or backport the WBX code
Jason
_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
Which file, *exactly* did you check?
What does 'uname -m' return on your system?
Did you by any chance do a binary install (via YUM) of Gnu Radio before
doing the source-based install from GIT?
--
Marcus Leech
Principal Investigator
Shirleys Bay Radio Astronomy Consortium
http://www.sbrac.org
_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
