Hi, Thank you for yor time, both of you. Finally, it's working. There were two issues. Firstly, as Alan wrote in the second mail, I missed the information in README that I can't access nsh strictly via USB. Secondly, the previous pico-sdk version (git reset --hard 26653ea81e340) was not working, but Release 1.1.2 and using :usbnsh option solved both problems.
Thank you very much once more. Your help saved me a lot of time. Have a nice week. Best regards, Lukas On Mon, 22 Nov 2021, 07:13 , <yuuichi.a.nakam...@sony.com> wrote: > Oops. I mistook the git option. Please use the following command. > > $ git clone -b1.1.2 master https://github.com/raspberrypi/pico-sdk.git > > > -----Original Message----- > From: Nakamura, Yuuichi (SGC) <yuuichi.a.nakam...@sony.com> > Sent: Monday, November 22, 2021 3:11 PM > To: dev@nuttx.apache.org; malek.l...@gmail.com > Cc: Nakamura, Yuuichi (SGC) <yuuichi.a.nakam...@sony.com> > Subject: RE: Raspberry Pi Pico Not Responing > > Hi Lukas and Alan, > > Would you try the following command to get the Raspberry Pi Pico SDK ? > > $ git clone -r1.1.2 master https://github.com/raspberrypi/pico-sdk.git > > NuttX for Raspberry Pi Pico uses a part of Pico SDK for bootloader, but > did not follow the latesd SDK update. > By using the fixed version tag instead of the master branch avoids the > problem. > > Please let me update the document for the present. > I'll follow the latest Pico SDK later. > > Best regards, > Yuuichi Nakamura > > -----Original Message----- > From: Alan Carvalho de Assis <acas...@gmail.com> > Sent: Monday, November 22, 2021 6:40 AM > To: Lukáš Málek <malek.l...@gmail.com> > Cc: dev <dev@nuttx.apache.org> > Subject: Re: Raspberry Pi Pico Not Responing > > I forgot to copy the mailing list, it could help other users in the future. > > BR, > > Alan > > On 11/21/21, Alan Carvalho de Assis <acas...@gmail.com> wrote: > > Hi Lukas, > > > > I just tested here using the usbnsh: > > > > ./tools/configure.sh raspberrypi-pico:usbnsh > > > > After compiled I copied the nuttx.uf2 to the rasp pico disk and opened > > the /dev/ttyACM0, then after pressing ENTER three times the NSH> show > > up: > > > > NuttShell (NSH) NuttX-10.2.0-RC0 > > nsh> uname -a > > NuttX 10.2.0-RC0 de4bd994f5 Nov 21 2021 18:32:45 arm raspberrypi-pico > > nsh> > > > > Probably you are using the incorrect pins when using the serial to get > > the default nsh, it is very common to happen, users mess with pins and > > TXD/RXD all the time. > > > > BR, > > > > Alan > > > > On 11/21/21, Lukáš Málek <malek.l...@gmail.com> wrote: > >> Hi Alan, > >> > >> Thank you for your time and a prompt reply. I followed your steps, > >> and the make command is working as expected. Unfortunately, after > >> uploading the uf2 file to the Qt Py RP2040, nothing happens. The > >> serial port is not responding at all. I have tried two more versions > >> of the pico-sdk library, the compilation was good. Still, after > >> compiling, I had the same problem. Do you have any ideas about what > >> could be wrong? The communication with the serial port should work > >> the same as with raspberry pi pico, so the problem should be > reproducible. > >> > >> Have a nice day! > >> > >> Best regards, > >> Lukas M > >> > >> > >> On 21/11/2021 20:15, Alan Carvalho de Assis wrote: > >>> Did it work for you? > >>> > >>> On 11/20/21, Alan Carvalho de Assis <acas...@gmail.com> wrote: > >>>> Hi Lukas, > >>>> > >>>> I just installed Ubuntu 21.04 and followed the README.txt and > >>>> duplicated your issue: > >>>> > >>>> $ sudo apt-get install automake bison build-essential flex > >>>> gcc-arm-none-eabi gperf git libncurses5-dev libtool libusb-dev > >>>> libusb-1.0.0-dev pkg-config git > >>>> > >>>> $ git clone -b master > >>>> https://urldefense.com/v3/__https://github.com/raspberrypi/pico-sdk > >>>> .git__;!!JmoZiZGBv3RvKRSx!oT1D7kZfyOPtmSvn3bXmLD--PF694blQfiUHI3xe4 > >>>> P_2h9PIHlISdJxYW6sWJkCcRldQBw$ [github[.]com] > >>>> > >>>> $ sudo mkdir /opt/rasp_pico > >>>> > >>>> $ sudo mv pico-sdk /opt/rasp_pico/ > >>>> > >>>> $ export PICO_SDK_PATH=/opt/rasp_pico/pico-sdk > >>>> > >>>> $ git clone > >>>> https://urldefense.com/v3/__https://github.com/apache/incubator-nut > >>>> tx.git__;!!JmoZiZGBv3RvKRSx!oT1D7kZfyOPtmSvn3bXmLD--PF694blQfiUHI3x > >>>> e4P_2h9PIHlISdJxYW6sWJkAhKvRhEA$ [github[.]com] nuttx > >>>> > >>>> $ git clone > >>>> https://urldefense.com/v3/__https://github.com/apache/incubator-nut > >>>> tx-apps.git__;!!JmoZiZGBv3RvKRSx!oT1D7kZfyOPtmSvn3bXmLD--PF694blQfi > >>>> UHI3xe4P_2h9PIHlISdJxYW6sWJkDnlA2lWQ$ [github[.]com] apps > >>>> > >>>> $ make distclean > >>>> NuttX has not been configured! > >>>> To configure the project: > >>>> tools/configure.sh <config> > >>>> For a list of available configurations: > >>>> tools/configure.sh -L > >>>> > >>>> $ ./tools/configure.sh raspberrypi-pico:nsh > >>>> > >>>> $ make > >>>> ... > >>>> > >>>> arm-none-eabi-gcc -nostartfiles -nodefaultlibs > >>>> -T/tmp/nuttx/boards/arm/rp2040/raspberrypi-pico/scripts/raspberrypi > >>>> -pico-flash.ld -DPICO_BOARD=\"pico\" -DPICO_BUILD=1 > >>>> -DPICO_NO_HARDWARE=0 > >>>> -DPICO_ON_DEVICE=1 -Ichip/boot2 > >>>> -I/opt/rasp_pico/pico-sdk/src/rp2_common/boot_stage2/asminclude > >>>> -I/opt/rasp_pico/pico-sdk/src/rp2040/hardware_regs/include > >>>> -I/opt/rasp_pico/pico-sdk/src/rp2_common/hardware_base/include > >>>> -I/opt/rasp_pico/pico-sdk/src/common/pico_base/include > >>>> -I/opt/rasp_pico/pico-sdk/src/boards/include > >>>> -I/opt/rasp_pico/pico-sdk/src/rp2_common/pico_platform/include -o > >>>> rp2040_boot_stage2.elf > >>>> /opt/rasp_pico/pico-sdk/src/rp2_common/boot_stage2/boot2_w25q080.S > >>>> In file included from > >>>> > /opt/rasp_pico/pico-sdk/src/rp2_common/pico_platform/include/pico/asm_helper.S:7, > >>>> from > >>>> /opt/rasp_pico/pico-sdk/src/rp2_common/boot_stage2/boot2_w25q080.S:29: > >>>> /opt/rasp_pico/pico-sdk/src/common/pico_base/include/pico.h:20:10: > >>>> fatal error: pico/version.h: No such file or directory > >>>> 20 | #include "pico/version.h" > >>>> | ^~~~~~~~~~~~~~~~ > >>>> compilation terminated. > >>>> make[2]: *** [chip/boot2/Make.defs:49: rp2040_boot_stage2.elf] > >>>> Error 1 > >>>> make[2]: Leaving directory '/tmp/nuttx/arch/arm/src' > >>>> make[1]: *** [Makefile:188: .depend] Error 2 > >>>> make[1]: Leaving directory '/tmp/nuttx/arch/arm/src' > >>>> make: *** [tools/Makefile.unix:494: pass2dep] Error 2 > >>>> > >>>> > >>>> I think there is some issue on their current repository because > >>>> version.h doesn't exist, it should be generated using cmake. > >>>> > >>>> Note it still referenced in their documentation: > >>>> https://urldefense.com/v3/__https://raspberrypi.github.io/pico-sdk- > >>>> doxygen/pico_8h_source.html__;!!JmoZiZGBv3RvKRSx!oT1D7kZfyOPtmSvn3b > >>>> XmLD--PF694blQfiUHI3xe4P_2h9PIHlISdJxYW6sWJkBJXpoTFw$ > >>>> [raspberrypi[.]github[.]io] > >>>> > >>>> I suggest you to return to the older version until we understand > >>>> how the new SDK work and modify NuttX to adapt to it. > >>>> > >>>> I fixed is here this way: > >>>> > >>>> $ cd /opt/rasp_pico/pico-sdk > >>>> > >>>> $ git reset --hard 26653ea81e340 > >>>> > >>>> BR, > >>>> > >>>> Alan > >>>> > >>>> On 11/20/21, Lukáš Málek <malek.l...@gmail.com> wrote: > >>>>> Dear Sir/Madam, > >>>>> > >>>>> I have been struggling for more than three days with building > >>>>> nuttx for Raspberry Pi Pico. I follow the guide Getting started. > >>>>> At the compilation, I run the following commands to compile the > >>>>> Nuttx. > >>>>> > >>>>> /$git clone -b master > >>>>> https://urldefense.com/v3/__https://github.com/raspberrypi/pico-sd > >>>>> k.git/*__;Lw!!JmoZiZGBv3RvKRSx!oT1D7kZfyOPtmSvn3bXmLD--PF694blQfiU > >>>>> HI3xe4P_2h9PIHlISdJxYW6sWJkB9z0hq5A$ [github[.]com] //$export > >>>>> PICO_SDK_PATH="<abs_path_to_pico-sdk>"// > >>>>> //$cd nuttx// > >>>>> //$./tools/configure.sh -l raspberrypi-pico:nsh// //$make/ > >>>>> > >>>>> Unfortunately, after making it, I got an error. > >>>>> /File pico/version.h can't be found/ > >>>>> > >>>>> At pico-SDK, I can see a file version.h.ini, so I rename it to > >>>>> version.h, but after that, I got an error message that /File > >>>>> "pico/config_autogen.h" can't be found/ > >>>>> > >>>>> This error is the dead-end for me. I have tried to comment the line. > >>>>> Also, I created the file that is attached, both resulting in a > >>>>> successful build. Unfortunately, the serial port is not working > >>>>> after uploading the u2f file to Qt Py RP2040 (Based on Raspberry Pi > Pico). > >>>>> In > >>>>> Device Manager and Zadig, I can see that nothing is connected to > >>>>> the port. Is it possible that during the build, the communication > >>>>> via USB is not activated? In this case, how can I do that? I have > >>>>> tested the serial port using CMake and pico-sdk. The communication > >>>>> via serial port worked, so there must be a problem with the > >>>>> software. > >>>>> > >>>>> I would be very grateful for any help since I have tried > >>>>> everything, but nothing worked. My nuttx folder, as well as the > >>>>> pico-SDK library, is attached. > >>>>> > >>>>> Sincerely, > >>>>> Lukas Malek > >> > > >
