Did it work for you?
On 11/20/21, Alan Carvalho de Assis <acas...@gmail.com> wrote: > Hi Lukas, > > I just installed Ubuntu 21.04 and followed the README.txt and > duplicated your issue: > > $ sudo apt-get install automake bison build-essential flex > gcc-arm-none-eabi gperf git libncurses5-dev libtool libusb-dev > libusb-1.0.0-dev pkg-config git > > $ git clone -b master https://github.com/raspberrypi/pico-sdk.git > > $ sudo mkdir /opt/rasp_pico > > $ sudo mv pico-sdk /opt/rasp_pico/ > > $ export PICO_SDK_PATH=/opt/rasp_pico/pico-sdk > > $ git clone https://github.com/apache/incubator-nuttx.git nuttx > > $ git clone https://github.com/apache/incubator-nuttx-apps.git apps > > $ make distclean > NuttX has not been configured! > To configure the project: > tools/configure.sh <config> > For a list of available configurations: > tools/configure.sh -L > > $ ./tools/configure.sh raspberrypi-pico:nsh > > $ make > ... > > arm-none-eabi-gcc -nostartfiles -nodefaultlibs > -T/tmp/nuttx/boards/arm/rp2040/raspberrypi-pico/scripts/raspberrypi-pico-flash.ld > -DPICO_BOARD=\"pico\" -DPICO_BUILD=1 -DPICO_NO_HARDWARE=0 > -DPICO_ON_DEVICE=1 -Ichip/boot2 > -I/opt/rasp_pico/pico-sdk/src/rp2_common/boot_stage2/asminclude > -I/opt/rasp_pico/pico-sdk/src/rp2040/hardware_regs/include > -I/opt/rasp_pico/pico-sdk/src/rp2_common/hardware_base/include > -I/opt/rasp_pico/pico-sdk/src/common/pico_base/include > -I/opt/rasp_pico/pico-sdk/src/boards/include > -I/opt/rasp_pico/pico-sdk/src/rp2_common/pico_platform/include -o > rp2040_boot_stage2.elf > /opt/rasp_pico/pico-sdk/src/rp2_common/boot_stage2/boot2_w25q080.S > In file included from > /opt/rasp_pico/pico-sdk/src/rp2_common/pico_platform/include/pico/asm_helper.S:7, > from > /opt/rasp_pico/pico-sdk/src/rp2_common/boot_stage2/boot2_w25q080.S:29: > /opt/rasp_pico/pico-sdk/src/common/pico_base/include/pico.h:20:10: > fatal error: pico/version.h: No such file or directory > 20 | #include "pico/version.h" > | ^~~~~~~~~~~~~~~~ > compilation terminated. > make[2]: *** [chip/boot2/Make.defs:49: rp2040_boot_stage2.elf] Error 1 > make[2]: Leaving directory '/tmp/nuttx/arch/arm/src' > make[1]: *** [Makefile:188: .depend] Error 2 > make[1]: Leaving directory '/tmp/nuttx/arch/arm/src' > make: *** [tools/Makefile.unix:494: pass2dep] Error 2 > > > I think there is some issue on their current repository because > version.h doesn't exist, it should be generated using cmake. > > Note it still referenced in their documentation: > https://raspberrypi.github.io/pico-sdk-doxygen/pico_8h_source.html > > I suggest you to return to the older version until we understand how > the new SDK work and modify NuttX to adapt to it. > > I fixed is here this way: > > $ cd /opt/rasp_pico/pico-sdk > > $ git reset --hard 26653ea81e340 > > BR, > > Alan > > On 11/20/21, Lukáš Málek <malek.l...@gmail.com> wrote: >> Dear Sir/Madam, >> >> I have been struggling for more than three days with building nuttx for >> Raspberry Pi Pico. I follow the guide Getting started. At the >> compilation, I run the following commands to compile the Nuttx. >> >> /$git clone -b master https://github.com/raspberrypi/pico-sdk.git// >> //$export PICO_SDK_PATH="<abs_path_to_pico-sdk>"// >> //$cd nuttx// >> //$./tools/configure.sh -l raspberrypi-pico:nsh// >> //$make/ >> >> Unfortunately, after making it, I got an error. >> /File pico/version.h can't be found/ >> >> At pico-SDK, I can see a file version.h.ini, so I rename it to >> version.h, but after that, I got an error message that >> /File "pico/config_autogen.h" can't be found/ >> >> This error is the dead-end for me. I have tried to comment the line. >> Also, I created the file that is attached, both resulting in a >> successful build. Unfortunately, the serial port is not working after >> uploading the u2f file to Qt Py RP2040 (Based on Raspberry Pi Pico). In >> Device Manager and Zadig, I can see that nothing is connected to the >> port. Is it possible that during the build, the communication via USB is >> not activated? In this case, how can I do that? I have tested the serial >> port using CMake and pico-sdk. The communication via serial port worked, >> so there must be a problem with the software. >> >> I would be very grateful for any help since I have tried everything, but >> nothing worked. My nuttx folder, as well as the pico-SDK library, is >> attached. >> >> Sincerely, >> Lukas Malek >
