Is anything printed?  Are the IP addresses set correctly?  You can
change all that, and enable DHCP if need be, from Apps -> Network
Utilities -> Network Initialization

On Fri, Feb 5, 2021 at 12:12 AM Matias N. <mat...@imap.cc> wrote:
>
> Thanks, I was looking at the DevKitC readme which does not have these 
> instructions.
> I cannot seem to connect though, not sure if it is because my router is set 
> to WPA2 TKIP+CCMP.
>
> Best,
> Matias
>
> On Thu, Feb 4, 2021, at 20:06, Abdelatif Guettouche wrote:
> > Basically you can just check the commands in the wlan_ioctl function
> > in esp32_wlan.c to see what's implemented.  But not much going on
> > there for the moment.
> > You can connect to access points.  Commands are given in the README.txt file
> > wapi psk wlan0 mypassword 1
> > wapi essid wlan0 myssid 1
> > You can also set these from menuconfig.
> >
> > > Also, I'm trying to scan and I get:
> >
> > That's because SIOCSIWSCAN isn't handled by the driver.
> > We have a branch internally to improve the driver and add more
> > features (SIOCSIWSCAN being one of them), I don't know when this one
> > will be submitted though.
> >
> > On Thu, Feb 4, 2021 at 11:55 PM Matias N. <mat...@imap.cc> wrote:
> > >
> > > Thanks, now the interface appears.
> > > What functionality is currently supported? Can I connect to WPA2 AP? Can 
> > > I create an AP?
> > >
> > > Also, I'm trying to scan and I get:
> > >
> > > nsh> wapi scan wlan0
> > > ioctl(SIOCSIWSCAN): 25
> > > ERROR: Process command (scan) failed.
> > >
> > > Thanks,
> > > Matias
> > >
> > > On Thu, Feb 4, 2021, at 19:36, Abdelatif Guettouche wrote:
> > > > It could be because there are some issues with getting the paramters 
> > > > from
> > > > the flash.  Please try disabling Save Paramters from the Wifi 
> > > > Configuration
> > > > menu.
> > > >
> > > > On Thu, Feb 4, 2021, 11:32 PM Matias N. <mat...@imap.cc> wrote:
> > > >
> > > > > Hi,
> > > > > I'm trying to test WiFi support on ESP32 DevKitC (I used wapi config) 
> > > > > and
> > > > > it does not seem to work. I get this:
> > > > >
> > > > > rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> > > > > configsip: 0, SPIWP:0xee
> > > > > clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> > > > > mode:DIO, clock div:2
> > > > > load:0x3fff0030,len:4
> > > > > load:0x3fff0034,len:6924
> > > > > load:0x40078000,len:13272
> > > > > load:0x40080400,len:3604
> > > > > entry 0x40080670
> > > > > I (29) boot: ESP-IDF v4.3-dev-1901-g178b122c1 2nd stage bootloader
> > > > > I (29) boot: compile time 17:16:52
> > > > > I (29) boot: chip revision: 1
> > > > > I (33) boot_comm: chip revision: 1, min. bootloader chip revision: 0
> > > > > I (40) boot.esp32: SPI Speed      : 40MHz
> > > > > I (45) boot.esp32: SPI Mode       : DIO
> > > > > I (49) boot.esp32: SPI Flash Size : 2MB
> > > > > I (54) boot: Enabling RNG early entropy source...
> > > > > I (59) boot: Partition Table:
> > > > > I (63) boot: ## Label            Usage          Type ST Offset   
> > > > > Length
> > > > > I (70) boot:  0 nvs              WiFi data        01 02 00009000 
> > > > > 00006000
> > > > > I (78) boot:  1 phy_init         RF data          01 01 0000f000 
> > > > > 00001000
> > > > > I (85) boot:  2 factory          factory app      00 00 00010000 
> > > > > 00100000
> > > > > I (93) boot: End of partition table
> > > > > I (97) boot_comm: chip revision: 1, min. application chip revision: 0
> > > > > I (104) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020
> > > > > size=0x0c22c ( 49708) map
> > > > > I (132) esp_image: segment 1: paddr=0x0001c254 vaddr=0x3ffb81e0
> > > > > size=0x0181c (  6172) load
> > > > > I (135) esp_image: segment 2: paddr=0x0001da78 vaddr=0x40080000
> > > > > size=0x00400 (  1024) load
> > > > > I (139) esp_image: segment 3: paddr=0x0001de80 vaddr=0x40080400
> > > > > size=0x02198 (  8600) load
> > > > > I (151) esp_image: segment 4: paddr=0x00020020 vaddr=0x400d0020
> > > > > size=0x59678 (366200) map
> > > > > I (296) esp_image: segment 5: paddr=0x000796a0 vaddr=0x40082598
> > > > > size=0x08718 ( 34584) load
> > > > > I (317) boot: Loaded app from partition at offset 0x10000
> > > > > I (317) boot: Disabling RNG early entropy source...
> > > > > esp32_rng_initialize: Initializing RNG
> > > > > esp_nvs_get_blob: INFO: No file /mnt/esp/wifi/wifi.misc.log
> > > > > esp_nvs_set_blob: ERROR: Failed to set open 
> > > > > /mnt/esp/wifi/wifi.misc.log
> > > > > W (85) wifi:nvs_log_init, osi_nvs_set_blob fail, key=log ret=ffffffff
> > > > >
> > > > > esp_wifi_init: ERROR: Failed to initialize WiFi error=-1
> > > > > esp_wifi_adapter_init: ERROR: Failed to initialize WiFi error=-1
> > > > > ERROR: Failed to initialize WiFi
> > > > >
> > > > > NuttShell (NSH) NuttX-10.0.1
> > > > > nsh> ifconfig
> > > > > nsh> ifup wlan0
> > > > > ifup wlan0...OK
> > > > > nsh> ifconfig
> > > > > nsh>
> > > > >
> > > > > I have used bootloader and partitions bin from
> > > > > https://github.com/saramonteiro/esp32_binaries_nuttx
> > > > >
> > > > > Thanks,
> > > > > Matias
> > > > >
> > > >
> >

Reply via email to