Thanks, I was looking at the DevKitC readme which does not have these instructions. I cannot seem to connect though, not sure if it is because my router is set to WPA2 TKIP+CCMP.
Best, Matias On Thu, Feb 4, 2021, at 20:06, Abdelatif Guettouche wrote: > Basically you can just check the commands in the wlan_ioctl function > in esp32_wlan.c to see what's implemented. But not much going on > there for the moment. > You can connect to access points. Commands are given in the README.txt file > wapi psk wlan0 mypassword 1 > wapi essid wlan0 myssid 1 > You can also set these from menuconfig. > > > Also, I'm trying to scan and I get: > > That's because SIOCSIWSCAN isn't handled by the driver. > We have a branch internally to improve the driver and add more > features (SIOCSIWSCAN being one of them), I don't know when this one > will be submitted though. > > On Thu, Feb 4, 2021 at 11:55 PM Matias N. <mat...@imap.cc> wrote: > > > > Thanks, now the interface appears. > > What functionality is currently supported? Can I connect to WPA2 AP? Can I > > create an AP? > > > > Also, I'm trying to scan and I get: > > > > nsh> wapi scan wlan0 > > ioctl(SIOCSIWSCAN): 25 > > ERROR: Process command (scan) failed. > > > > Thanks, > > Matias > > > > On Thu, Feb 4, 2021, at 19:36, Abdelatif Guettouche wrote: > > > It could be because there are some issues with getting the paramters from > > > the flash. Please try disabling Save Paramters from the Wifi > > > Configuration > > > menu. > > > > > > On Thu, Feb 4, 2021, 11:32 PM Matias N. <mat...@imap.cc> wrote: > > > > > > > Hi, > > > > I'm trying to test WiFi support on ESP32 DevKitC (I used wapi config) > > > > and > > > > it does not seem to work. I get this: > > > > > > > > rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) > > > > configsip: 0, SPIWP:0xee > > > > clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 > > > > mode:DIO, clock div:2 > > > > load:0x3fff0030,len:4 > > > > load:0x3fff0034,len:6924 > > > > load:0x40078000,len:13272 > > > > load:0x40080400,len:3604 > > > > entry 0x40080670 > > > > I (29) boot: ESP-IDF v4.3-dev-1901-g178b122c1 2nd stage bootloader > > > > I (29) boot: compile time 17:16:52 > > > > I (29) boot: chip revision: 1 > > > > I (33) boot_comm: chip revision: 1, min. bootloader chip revision: 0 > > > > I (40) boot.esp32: SPI Speed : 40MHz > > > > I (45) boot.esp32: SPI Mode : DIO > > > > I (49) boot.esp32: SPI Flash Size : 2MB > > > > I (54) boot: Enabling RNG early entropy source... > > > > I (59) boot: Partition Table: > > > > I (63) boot: ## Label Usage Type ST Offset Length > > > > I (70) boot: 0 nvs WiFi data 01 02 00009000 > > > > 00006000 > > > > I (78) boot: 1 phy_init RF data 01 01 0000f000 > > > > 00001000 > > > > I (85) boot: 2 factory factory app 00 00 00010000 > > > > 00100000 > > > > I (93) boot: End of partition table > > > > I (97) boot_comm: chip revision: 1, min. application chip revision: 0 > > > > I (104) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 > > > > size=0x0c22c ( 49708) map > > > > I (132) esp_image: segment 1: paddr=0x0001c254 vaddr=0x3ffb81e0 > > > > size=0x0181c ( 6172) load > > > > I (135) esp_image: segment 2: paddr=0x0001da78 vaddr=0x40080000 > > > > size=0x00400 ( 1024) load > > > > I (139) esp_image: segment 3: paddr=0x0001de80 vaddr=0x40080400 > > > > size=0x02198 ( 8600) load > > > > I (151) esp_image: segment 4: paddr=0x00020020 vaddr=0x400d0020 > > > > size=0x59678 (366200) map > > > > I (296) esp_image: segment 5: paddr=0x000796a0 vaddr=0x40082598 > > > > size=0x08718 ( 34584) load > > > > I (317) boot: Loaded app from partition at offset 0x10000 > > > > I (317) boot: Disabling RNG early entropy source... > > > > esp32_rng_initialize: Initializing RNG > > > > esp_nvs_get_blob: INFO: No file /mnt/esp/wifi/wifi.misc.log > > > > esp_nvs_set_blob: ERROR: Failed to set open /mnt/esp/wifi/wifi.misc.log > > > > W (85) wifi:nvs_log_init, osi_nvs_set_blob fail, key=log ret=ffffffff > > > > > > > > esp_wifi_init: ERROR: Failed to initialize WiFi error=-1 > > > > esp_wifi_adapter_init: ERROR: Failed to initialize WiFi error=-1 > > > > ERROR: Failed to initialize WiFi > > > > > > > > NuttShell (NSH) NuttX-10.0.1 > > > > nsh> ifconfig > > > > nsh> ifup wlan0 > > > > ifup wlan0...OK > > > > nsh> ifconfig > > > > nsh> > > > > > > > > I have used bootloader and partitions bin from > > > > https://github.com/saramonteiro/esp32_binaries_nuttx > > > > > > > > Thanks, > > > > Matias > > > > > > > >
