Robert,
I ended up with a little less time this weekend than I had hoped for.
Getting the "console" working is a little more tricky because of
restrictions put in place on modern machines that are booting in UEFI
mode. I was able to add some logic for booting via UEFI and
extracting framebuffer information to be able to draw on the screen,
just need to glue it together and then at least the output bit will
work with most video hardware. The input is a little more tricky
since that usually requires PCI + USB + HID.
You had mentioned that you hard coded the memory addresses found in
the scan. This probably means that you did not create a driver
interface. Neither of the two PCI examples that I created expose a
driver interface, but I could tweek the pci_edu driver to show how
this would work. You would register your driver in drivers/pci.c in
this struct:
struct pci_dev_type_s *pci_device_types[] =
{
#ifdef CONFIG_VIRT_QEMU_PCI_TEST
&pci_type_qemu_pci_test,
#endif /* CONFIG_VIRT_QEMU_PCI_TEST */
#ifdef CONFIG_VIRT_QEMU_EDU
&pci_type_qemu_edu,
#endif /* CONFIG_VIRT_QEMU_EDU */
NULL,
};
>From there you would then create and register a character or block
device and register the interfaces with it. The qemu_edu_probe shows
how your driver can collect this information which could then be
stored in a struct for your instance of your device. Then your
application would make a read/write/ioctrl call to /dev/mypcidev which
would then be handled by the kernel. Your application should not be
writing directly to physical memory addresses or doing things like
registering interrupts, that should be left to the device driver.
--Brennan
On Mon, Aug 3, 2020 at 11:47 AM Robert Faron <robe...@cmslaser.com> wrote:
>
> Brennen,
>
> Again I wanted to thanks you for the help you have provided thus far.
>
> After digging in to accessing pci devices in qemu I found that to virtualize
> PCi hardware you first need a board that supports VT-d. The Asus 885M-E
> motherboard only supports VT-x which allows for virtualization of 64bit OSes
> but doesn't support direct access to I/O. So this morning I started using
> Gigabyte H110N motherboard that does support VT-d. It took a bit of time to
> get the device to start using the vfio-pci kernel driver which allows qemu to
> access the card. Once that was complete I can now start qemu with "-device
> vfio-pci,host=01:00:0" and the qemu session now can see the card. The
> qemu_pci_init now can see the card and the Bar0 & Bar1 memory addresses.
> Using that I have written a very simple test program that can be enabled
> using "make menuconfig" called cms. Running cms from the nsh prompt access
> the card and turns on the isolated digital output then reads the state and
> reverses it.
>
> To continue my testing I would like to get the program cms to autorun that
> way I can at least test the I/o functionality. I will modify my program which
> is using hardcoded memory addresses to use the address found during a scan of
> the PCI configuration data so when it boots I can find the correct address as
> I assume it will be different when not in qemu
>
> I have tried using com1 (0x3f8) connected to coolterm on another computer to
> see if any terminal could be accessed but haven't had any success. I know you
> said you were going to work on getting a console up but having a serial
> terminal would work for now to keep my progress moving.
>
> -Robert
>
>
>
> -----Original Message-----
> From: Brennan Ashton <bash...@brennanashton.com>
> Sent: Friday, July 31, 2020 5:21 AM
> To: dev@nuttx.apache.org
> Subject: Re: AMD64 arch
>
> Robert,
> I dug into this a little more, and I am fairly confident that the PCI
> subsystem will find your device since it properly traverses the bridges and
> can identify multiple buses.
>
> A couple things that are probably important to check, you are not using the
> COM port on your motherboard for this testing right? There is no support for
> a VGA console right now and the OS is expecting to be able to write to the
> physical serial port.
>
> The warning you are getting in Grub is because the OS is asking for the
> bootloader to put the VGA controller in Text Mode, unfortunately that warning
> you are getting about the console is letting us know that the Grub is using
> UEFI which does not allow switching to text mode. I had implemented a VGA
> text mode console, but we cannot use this because of this limitation. I
> started adding support for the graphics mode so we can get a console drawn on
> the screen to help with debugging, but that is going to have to be a weekend
> project. I did get the graphics mode configured so I suspect it will not be
> too bad, but there are a lot of moving bits.
>
> --Brennan
>
> On Thu, Jul 30, 2020 at 2:24 PM Brennan Ashton <bash...@brennanashton.com>
> wrote:
> >
> > Robert,
> > I'll take a look this evening and get back to you.
> >
> > This has run on bare hardware before, as well as in a jailhouse cell,
> > so it should be fairly close to running on your hardware. I do most
> > of my testing inside of QEMU since it is much easier for me to attach
> > the debugger, but I'll see if I can still get this running directly on
> > my NUC.
> >
> > As for the multiple PCI busses I will need to look at that as well.
> > From what I remember the enumeration code structures handle the bus
> > id, but I would need to look at how we identify the buses that we
> > scan.
> >
> > This is actually all timely because I just got some PCIe hardware that
> > I have been waiting for for a few months, so let's see what we can do.
> >
> > --Brennan
> NOTICE: This e-mail message and all attachments transmitted with it may
> contain trade secrets and confidential information intended solely for the
> use of the addressee. If the reader of this message is not the intended
> recipient, you are hereby notified that any reading, dissemination,
> distribution, copying, or other use of this message or its attachments is
> strictly prohibited. If you have received this message in error, please
> notify the sender immediately by telephone at 407-679-9716, and delete this
> message and all copies and backups thereof. Thank you
