<snip>

> > >>>
> > >>> On 2023/2/20 14:08, Ashok Kaladi wrote:
> > >>>> If ethdev enqueue or dequeue function is called during
> > >>>> eth_dev_fp_ops_setup(), it may get pre-empted after setting the
> > >>>> function pointers, but before setting the pointer to port data.
> > >>>> In this case the newly registered enqueue/dequeue function will
> > >>>> use dummy port data and end up in seg fault.
> > >>>>
> > >>>> This patch moves the updation of each data pointers before
> > >>>> updating corresponding function pointers.
> > >>>>
> > >>>> Fixes: c87d435a4d79 ("ethdev: copy fast-path API into separate
> > >>>> structure")
> > >>>> Cc: sta...@dpdk.org
> > >
> > > Why is something calling enqueue/dequeue when device is not fully
> started.
> > > A correctly written application would not call rx/tx burst until
> > > after ethdev start had finished.
> >
> > Please refer the eb0d471a894 (ethdev: add proactive error handling
> > mode), when driver recover itself, the application may still invoke
> enqueue/dequeue API.
> 
> Right now DPDK ethdev layer *does not* provide synchronization
> mechanisms between data-path and control-path functions.
> That was a deliberate deisgn choice. If we want to change that rule, then I
> suppose we need a community consensus for it.
> I think that if the driver wants to provide some sort of error recovery
> procedure, then it has to provide some synchronization mechanism inside it
> between data-path and control-path functions.
> Actually looking at eb0d471a894 (ethdev: add proactive error handling
> mode), and following patches I wonder how it creeped in?
> It seems we just introduced a loophole for race condition with this
> approach...
> It probably needs to be either deprecated or reworked.
Looking at the commit, it does not say anything about the data plane functions 
which probably means, the error recovery is happening within the data plane 
thread. What happens to other data plane threads that are polling the same port 
on which the error recovery is happening?

Also, the commit log says that while the error recovery is under progress, the 
application should not call any control plane APIs. Does that mean, the 
application has to check for error condition every time it calls a control 
plane API?

The commit message also says that "PMD makes sure the control path operations 
failed with retcode -EBUSY". It does not say how it does this. But, any 
communication from the PMD thread to control plane thread may introduce race 
conditions if not done correctly.

> 
> >
> > >
> > > Would something like this work better?
> > >
> > > Note: there is another bug in current code. The check for link state
> > > interrupt and link_ops could return -ENOTSUP and leave device in
> indeterminate state.
> > > The check should be done before calling PMD.
> > >
> > > diff --git a/lib/ethdev/rte_ethdev.c b/lib/ethdev/rte_ethdev.c index
> > > 0266cc82acb6..d6c163ed85e7 100644
> > > --- a/lib/ethdev/rte_ethdev.c
> > > +++ b/lib/ethdev/rte_ethdev.c
> > > @@ -1582,6 +1582,14 @@ rte_eth_dev_start(uint16_t port_id)
> > >           return 0;
> > >   }
> > >
> > > + if (dev->data->dev_conf.intr_conf.lsc == 0 &&
> > > +     dev->dev_ops->link_update == NULL) {
> > > +         RTE_ETHDEV_LOG(INFO,
> > > +                        "Device with port_id=%"PRIu16" link update not
> supported\n",
> > > +                        port_id);
> > > +                 return -ENOTSUP;
> > > + }
> > > +
> > >   ret = rte_eth_dev_info_get(port_id, &dev_info);
> > >   if (ret != 0)
> > >           return ret;
> > > @@ -1591,9 +1599,7 @@ rte_eth_dev_start(uint16_t port_id)
> > >           eth_dev_mac_restore(dev, &dev_info);
> > >
> > >   diag = (*dev->dev_ops->dev_start)(dev);
> > > - if (diag == 0)
> > > -         dev->data->dev_started = 1;
> > > - else
> > > + if (diag != 0)
> > >           return eth_err(port_id, diag);
> > >
> > >   ret = eth_dev_config_restore(dev, &dev_info, port_id); @@ -1611,16
> > > +1617,18 @@ rte_eth_dev_start(uint16_t port_id)
> > >           return ret;
> > >   }
> > >
> > > - if (dev->data->dev_conf.intr_conf.lsc == 0) {
> > > -         if (*dev->dev_ops->link_update == NULL)
> > > -                 return -ENOTSUP;
> > > -         (*dev->dev_ops->link_update)(dev, 0);
> > > - }
> > > -
> > >   /* expose selection of PMD fast-path functions */
> > >   eth_dev_fp_ops_setup(rte_eth_fp_ops + port_id, dev);
> > >
> > > + /* ensure state is set before marking device ready */
> > > + rte_smp_wmb();
> > > +
> > >   rte_ethdev_trace_start(port_id);
> > > +
> > > + /* Update current link state */
> > > + if (dev->data->dev_conf.intr_conf.lsc == 0)
> > > +         (*dev->dev_ops->link_update)(dev, 0);
> > > +
> > >   return 0;
> > >  }
> > >
> > >
> > > .
> > >

Reply via email to