On 1/22/2021 9:01 AM, Steve Yang wrote:
The offloads of 'tx/rx_conf' didn't keep up with the corresponding
offloads of 'dev_conf' if rx queue capability was 0, it would cause
the configuration invalid.
For example:
Configuring 'max-pkt-len' would change 'rx_offloads' in dev_conf while
rx_conf.offloads of each queue still kept the old value.
It would cause the failure of offloads check in 'rte_eth_rx_queue_setup'.
This patch applied tx/rx offloads configuration for each queue
once it changed and corresponding tx/rx queue capability was 0.
Fixes: 5e91aeef218c ("app/testpmd: fix offload flags after port config")
Signed-off-by: Steve Yang <stevex.y...@intel.com>
---
app/test-pmd/testpmd.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/app/test-pmd/testpmd.c b/app/test-pmd/testpmd.c
index a2c9aad960..8307c7f9e9 100644
--- a/app/test-pmd/testpmd.c
+++ b/app/test-pmd/testpmd.c
@@ -3296,7 +3296,11 @@ rxtx_port_config(struct rte_port *port)
for (qid = 0; qid < nb_rxq; qid++) {
offloads = port->rx_conf[qid].offloads;
port->rx_conf[qid] = port->dev_info.default_rxconf;
- if (offloads != 0)
+ if (port->dev_info.rx_queue_offload_capa == 0 &&
+ offloads != port->dev_conf.rxmode.offloads)
+ port->rx_conf[qid].offloads =
+ port->dev_conf.rxmode.offloads;
+ else if (offloads != 0)
port->rx_conf[qid].offloads = offloads;
I am still concerned to use port offloads to set the queue specific offloads,
this may lead unexpected result.
Below is what Steve provided as reproduce steps [1], I think that is application
(testpmd) miss-configuration to update 'max-pkt-len' but not update the
JUMBO_FRAME offload flag and MTU accordingly.
What do you think update the JUMBO_FRAME offload flag (both for port and queues)
according and set MTU according on the testpmd command where 'max-pkt-len' is
set? This is more like your first version.
[1]
----------------------------------------------
# x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -- -i
--max-pkt-len=9000 --tx-offloads=0x8000 --rxq=4 --txq=4 --disable-rss
testpmd> set verbose 3
testpmd> start
testpmd> stop
testpmd> port stop all
testpmd> port config all max-pkt-len 1518
testpmd> port start all
Configuring Port 0 (socket 1)
Ethdev port_id=0 rx_queue_id=0, new added offloads 0x800 must be within
per-queue offload capabilities 0x0 in rte_eth_rx_queue_setup()
Fail to configure port 0 rx queues//<-- Fail error info;
------------------------------------------------
/* Check if any Rx parameters have been passed */
@@ -3321,7 +3325,11 @@ rxtx_port_config(struct rte_port *port)
for (qid = 0; qid < nb_txq; qid++) {
offloads = port->tx_conf[qid].offloads;
port->tx_conf[qid] = port->dev_info.default_txconf;
- if (offloads != 0)
+ if (port->dev_info.tx_queue_offload_capa == 0 &&
+ offloads != port->dev_conf.txmode.offloads)
+ port->tx_conf[qid].offloads =
+ port->dev_conf.txmode.offloads;
+ else if (offloads != 0)
port->tx_conf[qid].offloads = offloads;
/* Check if any Tx parameters have been passed */
