Loopback mode is also supported on X540 and X550 NICs, according to
their datasheet (section 15.2). The way to set it up is a little
different of the 82599.

Signed-off-by: Julien Meunier <julien.meun...@nokia.com>
---
v2:
- disable / enable autoneg when loopback is requested for X540 / X550
---
 drivers/net/ixgbe/base/ixgbe_type.h |  1 +
 drivers/net/ixgbe/base/ixgbe_x540.c | 26 ++++++++++++++++
 drivers/net/ixgbe/base/ixgbe_x540.h |  2 ++
 drivers/net/ixgbe/base/ixgbe_x550.c | 26 ++++++++++++++++
 drivers/net/ixgbe/base/ixgbe_x550.h |  1 +
 drivers/net/ixgbe/ixgbe_ethdev.h    |  5 ++-
 drivers/net/ixgbe/ixgbe_rxtx.c      | 61 +++++++++++++++++++++++++++++++++++--
 7 files changed, 117 insertions(+), 5 deletions(-)

diff --git a/drivers/net/ixgbe/base/ixgbe_type.h 
b/drivers/net/ixgbe/base/ixgbe_type.h
index 077b8f0..c4af31e 100644
--- a/drivers/net/ixgbe/base/ixgbe_type.h
+++ b/drivers/net/ixgbe/base/ixgbe_type.h
@@ -1649,6 +1649,7 @@ struct ixgbe_dmac_config {
 #define IXGBE_MII_5GBASE_T_ADVERTISE           0x0800
 #define IXGBE_MII_100BASE_T_ADVERTISE          0x0100 /* full duplex, bit:8 */
 #define IXGBE_MII_100BASE_T_ADVERTISE_HALF     0x0080 /* half duplex, bit:7 */
+#define IXGBE_MII_AUTONEG_ENABLE               0x1000
 #define IXGBE_MII_RESTART                      0x200
 #define IXGBE_MII_AUTONEG_COMPLETE             0x20
 #define IXGBE_MII_AUTONEG_LINK_UP              0x04
diff --git a/drivers/net/ixgbe/base/ixgbe_x540.c 
b/drivers/net/ixgbe/base/ixgbe_x540.c
index f00f0ea..a241d41 100644
--- a/drivers/net/ixgbe/base/ixgbe_x540.c
+++ b/drivers/net/ixgbe/base/ixgbe_x540.c
@@ -1032,3 +1032,29 @@ s32 ixgbe_blink_led_stop_X540(struct ixgbe_hw *hw, u32 
index)
 
        return IXGBE_SUCCESS;
 }
+
+/*
+ *  ixgbe_setup_phy_link_x540 - Enable/disable the autoneg
+ *  @hw: pointer to hardware structure
+ *  enable: enable/disable the autoneg
+ **/
+s32 ixgbe_setup_phy_autoneg_x540(struct ixgbe_hw *hw, bool enable)
+{
+       s32 status = IXGBE_SUCCESS;
+       u16 autoneg_reg = IXGBE_MII_AUTONEG_REG;
+
+       DEBUGFUNC("ixgbe_setup_phy_autoneg_x540");
+
+       hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+                            IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+
+       if (enable)
+               autoneg_reg |= IXGBE_MII_AUTONEG_ENABLE;
+       else
+               autoneg_reg &= ~IXGBE_MII_AUTONEG_ENABLE;
+
+       hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+                             IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+
+       return status;
+}
diff --git a/drivers/net/ixgbe/base/ixgbe_x540.h 
b/drivers/net/ixgbe/base/ixgbe_x540.h
index 231dfe5..ef939ce 100644
--- a/drivers/net/ixgbe/base/ixgbe_x540.h
+++ b/drivers/net/ixgbe/base/ixgbe_x540.h
@@ -34,5 +34,7 @@ void ixgbe_init_swfw_sync_X540(struct ixgbe_hw *hw);
 
 s32 ixgbe_blink_led_start_X540(struct ixgbe_hw *hw, u32 index);
 s32 ixgbe_blink_led_stop_X540(struct ixgbe_hw *hw, u32 index);
+
+s32 ixgbe_setup_phy_autoneg_x540(struct ixgbe_hw *hw, bool enable);
 #endif /* _IXGBE_X540_H_ */
 
diff --git a/drivers/net/ixgbe/base/ixgbe_x550.c 
b/drivers/net/ixgbe/base/ixgbe_x550.c
index a920a14..f4ee188 100644
--- a/drivers/net/ixgbe/base/ixgbe_x550.c
+++ b/drivers/net/ixgbe/base/ixgbe_x550.c
@@ -4652,3 +4652,29 @@ bool ixgbe_fw_recovery_mode_X550(struct ixgbe_hw *hw)
 
        return !!(fwsm & IXGBE_FWSM_FW_NVM_RECOVERY_MODE);
 }
+
+/*
+ *  ixgbe_setup_phy_link_x550 - Enable/disable the autoneg
+ *  @hw: pointer to hardware structure
+ *  enable: enable/disable the autoneg
+ **/
+s32 ixgbe_setup_phy_autoneg_x550(struct ixgbe_hw *hw, bool enable)
+{
+       s32 status = IXGBE_SUCCESS;
+       u16 autoneg_reg = IXGBE_MII_AUTONEG_REG;
+
+       DEBUGFUNC("ixgbe_setup_phy_autoneg_x550");
+
+       hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+                            IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+
+       if (enable)
+               autoneg_reg |= IXGBE_MII_AUTONEG_ENABLE;
+       else
+               autoneg_reg &= ~IXGBE_MII_AUTONEG_ENABLE;
+
+       hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+                             IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+
+       return status;
+}
diff --git a/drivers/net/ixgbe/base/ixgbe_x550.h 
b/drivers/net/ixgbe/base/ixgbe_x550.h
index 3bd98f2..dd4fa18 100644
--- a/drivers/net/ixgbe/base/ixgbe_x550.h
+++ b/drivers/net/ixgbe/base/ixgbe_x550.h
@@ -93,4 +93,5 @@ s32 ixgbe_identify_sfp_module_X550em(struct ixgbe_hw *hw);
 s32 ixgbe_led_on_t_X550em(struct ixgbe_hw *hw, u32 led_idx);
 s32 ixgbe_led_off_t_X550em(struct ixgbe_hw *hw, u32 led_idx);
 bool ixgbe_fw_recovery_mode_X550(struct ixgbe_hw *hw);
+s32 ixgbe_setup_phy_autoneg_x550(struct ixgbe_hw *hw, bool enable);
 #endif /* _IXGBE_X550_H_ */
diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
index 565c69c..c60a697 100644
--- a/drivers/net/ixgbe/ixgbe_ethdev.h
+++ b/drivers/net/ixgbe/ixgbe_ethdev.h
@@ -65,9 +65,8 @@
 #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT       500 /* 500us */
 
 /* Loopback operation modes */
-/* 82599 specific loopback operation types */
-#define IXGBE_LPBK_82599_NONE   0x0 /* Default value. Loopback is disabled. */
-#define IXGBE_LPBK_82599_TX_RX  0x1 /* Tx->Rx loopback operation is enabled. */
+#define IXGBE_LPBK_NONE   0x0 /* Default value. Loopback is disabled. */
+#define IXGBE_LPBK_TX_RX  0x1 /* Tx->Rx loopback operation is enabled. */
 
 #define IXGBE_MAX_JUMBO_FRAME_SIZE      0x2600 /* Maximum Jumbo frame size. */
 
diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c
index c9a70a8..1472d13 100644
--- a/drivers/net/ixgbe/ixgbe_rxtx.c
+++ b/drivers/net/ixgbe/ixgbe_rxtx.c
@@ -49,6 +49,8 @@
 #include "ixgbe_ethdev.h"
 #include "base/ixgbe_dcb.h"
 #include "base/ixgbe_common.h"
+#include "base/ixgbe_x540.h"
+#include "base/ixgbe_x550.h"
 #include "ixgbe_rxtx.h"
 
 #ifdef RTE_LIBRTE_IEEE1588
@@ -3174,6 +3176,7 @@ ixgbe_dev_clear_queues(struct rte_eth_dev *dev)
        unsigned i;
        struct ixgbe_adapter *adapter =
                (struct ixgbe_adapter *)dev->data->dev_private;
+       struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
 
        PMD_INIT_FUNC_TRACE();
 
@@ -3194,6 +3197,15 @@ ixgbe_dev_clear_queues(struct rte_eth_dev *dev)
                        ixgbe_reset_rx_queue(adapter, rxq);
                }
        }
+       /* If loopback mode was enabled, reconfigure the link accordingly */
+       if (dev->data->dev_conf.lpbk_mode != 0) {
+               if (hw->mac.type == ixgbe_mac_X540)
+                       ixgbe_setup_phy_autoneg_x540(hw, true);
+               else if (hw->mac.type == ixgbe_mac_X550 ||
+                    hw->mac.type == ixgbe_mac_X550EM_x ||
+                    hw->mac.type == ixgbe_mac_X550EM_a)
+                       ixgbe_setup_phy_autoneg_x550(hw, true);
+       }
 }
 
 void
@@ -5074,8 +5086,12 @@ ixgbe_check_supported_loopback_mode(struct rte_eth_dev 
*dev)
 {
        struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
 
-       if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
-               if (hw->mac.type == ixgbe_mac_82599EB)
+       if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
+               if (hw->mac.type == ixgbe_mac_82599EB ||
+                    hw->mac.type == ixgbe_mac_X540 ||
+                    hw->mac.type == ixgbe_mac_X550 ||
+                    hw->mac.type == ixgbe_mac_X550EM_x ||
+                    hw->mac.type == ixgbe_mac_X550EM_a)
                        return 0;
 
        return -ENOTSUP;
@@ -5108,6 +5124,41 @@ ixgbe_setup_loopback_link_82599(struct ixgbe_hw *hw)
        msec_delay(50);
 }
 
+/*
+ * Set up link loopback for X540 mode Tx->Rx.
+ */
+static inline void __attribute__((cold))
+ixgbe_setup_loopback_link_x540(struct ixgbe_hw *hw)
+{
+       uint32_t macc;
+       PMD_INIT_FUNC_TRACE();
+
+       /* datasheet 15.2.1: disable AUTONEG (PHY Bit 7.0.C) */
+       ixgbe_setup_phy_autoneg_x540(hw, false);
+
+       /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
+       macc = IXGBE_READ_REG(hw, IXGBE_MACC);
+       macc |= IXGBE_MACC_FLU;
+       IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
+}
+
+/*
+ * Set up link loopback for X550 mode Tx->Rx.
+ */
+static inline void __attribute__((cold))
+ixgbe_setup_loopback_link_x550(struct ixgbe_hw *hw)
+{
+       uint32_t macc;
+       PMD_INIT_FUNC_TRACE();
+
+       /* datasheet 15.2.1: disable AUTONEG (PHY Bit 7.0.C) */
+       ixgbe_setup_phy_autoneg_x550(hw, false);
+
+       /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
+       macc = IXGBE_READ_REG(hw, IXGBE_MACC);
+       macc |= IXGBE_MACC_FLU;
+       IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
+}
 
 /*
  * Start Transmit and Receive Units.
@@ -5172,6 +5223,12 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev *dev)
        if (dev->data->dev_conf.lpbk_mode != 0) {
                if (hw->mac.type == ixgbe_mac_82599EB)
                        ixgbe_setup_loopback_link_82599(hw);
+               else if (hw->mac.type == ixgbe_mac_X540)
+                       ixgbe_setup_loopback_link_x540(hw);
+               else if (hw->mac.type == ixgbe_mac_X550 ||
+                    hw->mac.type == ixgbe_mac_X550EM_x ||
+                    hw->mac.type == ixgbe_mac_X550EM_a)
+                       ixgbe_setup_loopback_link_x550(hw);
        }
 
 #ifdef RTE_LIBRTE_SECURITY
-- 
2.10.2

Reply via email to