On Friday 31 July 2015 23:39:37 tan...@hushmail.com wrote: > >> Outcome 1 > >> > >> eth0 Link encap:Ethernet HWaddr 10:c3:7b:9d:d0:d2 > >> inet6 addr: fe80::12c3:7bff:fe9d:d0d2/64 Scope:Link > >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > >> RX packets:10 errors:0 dropped:0 overruns:0 frame:0 > >> TX packets:28 errors:0 dropped:0 overruns:0 carrier:0 > >> collisions:0 txqueuelen:1000 > >> RX bytes:614 (614.0 B) TX bytes:4184 (4.0 KiB) > >> > >> lo Link encap:Local Loopback > >> inet addr:127.0.0.1 Mask:255.0.0.0 > >> inet6 addr: ::1/128 Scope:Host > >> UP LOOPBACK RUNNING MTU:65536 Metric:1 > >> RX packets:378 errors:0 dropped:0 overruns:0 frame:0 > >> TX packets:378 errors:0 dropped:0 overruns:0 carrier:0 > >> collisions:0 txqueuelen:0 > >> RX bytes:30580 (29.8 KiB) TX bytes:30580 (29.8 KiB) > >> > >> ppp0 Link encap:Point-to-Point Protocol > >> inet addr:219.77.72.189 P-t-P:203.218.189.254 > >> Mask:255.255.255.255 > >> UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 > >> Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX > >> packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 > >> txqueuelen:3 > >> RX bytes:94 (94.0 B) TX bytes:54 (54.0 B) > >> > >> > >> > >> NY > > > >It appears that someone is trying to enforce IPV6 addressing only. > > Where I'm at, thats plain stupid since the nearest IPV6 capable > > circuit is more than likely in Pitsburgh, 3+ interstate 79 hours > > north of me. > > > >Theres an option someplace in one of the (NetworkMangler?) configs to > >disable that, but I don't have my hands on that doc ATM. > > > >Cheers, Gene Heskett > > -- > > Outcome 1 above was what I got by running "pon dsl-provider" and > ifconfig. I disabled IPV6 (Is that what you meant?) using the kernel > boot option ipv6.disable=1. It didn't help. > > Now instead of outcome 1 I have > > eth0 Link encap:Ethernet HWaddr 10:c3:7b:9d:d0:d2 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:61 errors:0 dropped:0 overruns:0 frame:0 > TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:5301 (5.1 KiB) TX bytes:1162 (1.1 KiB) > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:65536 Metric:1 > RX packets:714 errors:0 dropped:0 overruns:0 frame:0 > TX packets:714 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:57796 (56.4 KiB) TX bytes:57796 (56.4 KiB) > > ppp0 Link encap:Point-to-Point Protocol > inet addr:218.102.185.241 P-t-P:203.218.189.254 > Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 > Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX > packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 > txqueuelen:3 > RX bytes:1797 (1.7 KiB) TX bytes:54 (54.0 B) > > BTW I forgot to mention that I had rerun pppoeconf to set up the > connection, which didn't help either. > > Thanks! > > NY
The only place you are getting an IPV4 address is ppp0. And to get that you are running pppoeconf. Are you equipt with some sort of a phone modem card in your machine? I have a bag of those things but its been 15 years since I last actually used one. In the above sampling, 2 things are dead wrong. 1. Mask is restricted to the exact address when the setting is 255.255.255.255. Much more normal would be to zero the last triplet. 2. That however would still block the P-t-P address as its in a different block of 255 addresses. You would have to zero the last 2 triplets before you could even ping the P-t-P address shown. My memory is fuzzy at best as its also 80 yo, so if you are truly dealing with a modem card and a dialup phone line, someone who has done this recently needs to chime in and advise. I am not equipt with recent enough experience to be of any help. Everything that I have written assumes the first rj45 jack is connected to a router, and that the router is connected to a ca ble or DSL modem. Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: https://lists.debian.org/201508010248.34181.ghesk...@wdtv.com
