Le mardi 19 janvier 2010 à 06:45 +0000, Christian Koerner a écrit :
> On Mon, 18 Jan 2010, amka wrote:
>
> > Le dimanche 17 janvier 2010 à 00:11 +0000, Christian Koerner a écrit :
> >> On Sun, 17 Jan 2010, amka wrote:
> >
> >>> Le samedi 16 janvier 2010 à 21:37 +0000, Christian Koerner a écrit :
> >>>> On Sat, 16 Jan 2010, amka wrote:
> >>>>> On boot :
> >>>>>
> >>>>> ramdisk: couldn't find valid ram disk image starting at 0
> >>>>> list of all partitions:
> >>>>> ... # I don't remember the line, and the last one is :
> >>>>>
> >>>>> Kernel Panic - not syncing: VFS: unable to mount root FS on unknown
> >>>>> block (8,33)
> >>>>
> >>>> Looks like it can't find the initrd image.
> >>>
> >>>> How many HDDs have you in your system?
> >>> 3 : sda, sdb (etch) and sdc (lenny)
> >>
> >> Can you boot into Etch or does it fail too?
> > The boot of etch is OK (lilo).
> >
> >> What filesystem do you use for lenny?
> > ext3 :
> >
> > 1. it's visible on /etc/fstab , and
> >
> >
> > 2. On etch, I mounted /dev/sdc1 (='/' lenny) on :
> > debian:~# stat -f /mnt/wd01/
> > File: "/mnt/wd01/"
> > ID: 0 Namelen: 255 Type: ext2/ext3
> > Block size: 4096 Fundamental block size: 4096
> > Blocks: Total: 35325708 Free: 34536368 Available: 32741908
> > Inodes: Total: 8978432 Free: 8879709
> >
> loader=chain-loader
I tried, see below (lenny lilo.conf ; no results...)
> Do you use lilo also for etch? If so, can you send your lilo.conf from the
> etch installation.
etch lilo.conf :
boot=/dev/sdb
map=/boot/map
prompt
delay=100
timeout=100
default=Debian40
image=/vmlinuz
root=/dev/sdb2
label=Debian40
read-only
# restricted
initrd=/initrd.img
other=/dev/sdc
label=Debian50
> >> In your lilo.conf I would remove any options with "*bmp* and the "install"
> >> option.
> > Yes, and result : the boot problem subsists.
> >
> >> Had you a chance to disconnect drive sda & sdb as I would keep it as
> >> simple as possible. Hence remove also any options with bmp and the install
> >> option in your lilo configuration.
> > I did, and the problem subsists too (1 drive only and no bmp or install
> > options).
>
> When you tested with the Lenny HDD, did you change your lilo.conf before? So
> all /dev/sdc devices pointed to /dev/sda?
How I did :
1. I started my computer with the first lenny CD ;
graphical rescue mode.
2. I mount /dev/sda1 for '/'
3. I went to shell (, got the mount and df results), and
I changed my lilo.conf :
lenny lilo.conf (only 1 disk) :
lba32
boot=/dev/sda
root=/dev/sda1
prompt
timeout=50
map=/boot/map
loader=chain-loader
vga=normal
image=/boot/vmlinuz-2.6.26-2-amd64
label="lenny_1D"
initrd=/boot/initrd.img-2.6.26-2-amd64
read-only
The result was the same when I started with "lenny_1D" : kernel panic.
> > And a strange thing :
> > - The rescue mode invited me to mount /dev/sda1 on '/' , normal, but...
> > - df prints /dev/sdc1/ (and not sda1) as '/' ??
> > - Changing /etc/fstab or SATA connectors on my drive didn't change anything.
>
> Can you please send the output of mount and df when you use one disk only.
Here you have them :
df:
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sdc1 141302832 3157216 130967776 3% /
tmpfs 141302832 3157216 130967776 3% /lib/init/rw
udev 514680 660 514020 1% /dev
tmpfs 514680 660 514020 1% /dev/shm
devpts 514680 660 514020 1% /dev/pts
mount:
dev/sdc1 on / type ext3 (rw,errors=remount-ro)
tmpfs on /lib/init/rw type tmpfs (rw,nosuid,mode=0755)
proc on /proc type proc (rw,noexec,nosuid,nodev)
sysfs on /sys type sysfs (rw,noexec,nosuid,nodev)
procbususb on /proc/bus/usb type usbfs (rw)
udev on /dev type tmpfs (rw,mode=0755)
tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev)
devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=620)
> >>>> On what HDD/partiton did you install lilo?
> >>> On sdc. I tried sda, but the problem subsist.
> >>>
> >> Do you boot directly into Lilo or do you use another bootloader that
> >> starts Lilo?
> >
> > Lilo starts first.
> >
> > Another thing I saw :
> > On boot, an error/warning occurs :
> > [ [0.260762 PCI ] cannot alocate ressource region 0 for device
> > 0000:00:00:0
> >
> > I am not sure for the quite text (it goes fast, but :
> > - The first number is correct,
> > - 'region' is '0' and
> > - 'device' is "a lot of" 0.
> >
> > debian:/home/amel# lspci
> > 00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-8151 System
> > Controller (rev 13)
> > 00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8151 AGP Bridge
> > (rev 13)
> >
> > My TYAN Tiger K8W (S2875) mainboard seems to be supported.
> > http://kmuto.jp/debian/hcl/Tyan/Tiger+K8W+(S2875)
Kind regards
--
To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
