Could you be so kind as to point me to the place where I can find the visor module option in make menuconfig? I cant seem to find it. Maybe I'm looking the wrong place. I'm using v2.4.18 BTW.
davidc On Fri, 2002-12-20 at 14:39, Bret Comstock Waldow wrote: > I just installed Woody r1 (presumably, as I connected to sources on the > net while installing, and it downloaded a lot of stuff). I included > pilot-link, gnome-pilot, evolution, and the things they each said they > depended on. The kernel is 2.2.20. > > I have been running Redhat 7.3, and have been reliably synch'ing my > Handspring Visor Prism for months. I know this works - I've been doing > it. > > It's not happening with Debian so far though. I've appended some > information at the end of this message. > > The visor modules reports as loaded, but the error message seems to say > it's not. I'm not at all sure how to proceed from here. I've read the > Visor mini-HowTo - that's how I got it working in Redhat. Nothing in > that document seems relevant here - I followed all the steps again, and > that doesn't seem to be it. This appears to be the relevant issue: > > Dec 20 10:50:37 ganesha /etc/hotplug/usb.agent: missing kernel or user > mode driver visor > > lsmod says the visor modules is loaded. > > Directly attempting the hotsync with pilot-link, a la the HowTo, gets a > message about pi_bind: > Unable to bind to port /dev/ttyUSB1 > pi_bind: Permission denied > > > Any thoughts, please? > > Bret > > ======================================================================== > Two attempts to hotsync - and the results from /var/log/messages: > > Dec 20 10:49:50 ganesha kernel: hub.c: USB new device connect on bus1/1, > assigned device number 3 > Dec 20 10:49:50 ganesha kernel: usb.c: USB new device connect, assigned > device number 3 > Dec 20 10:49:50 ganesha kernel: usb.c: USB device 3 (vend/prod > 0x82d/0x100) is not claimed by any active driver. > Dec 20 10:49:50 ganesha /etc/hotplug/usb.agent: Setup visor for USB > product 82d/100/0100 > Dec 20 10:49:50 ganesha kernel: usbserial.c: USB Serial support > registered for Generic > Dec 20 10:49:50 ganesha kernel: usb.c: registered new driver serial > Dec 20 10:49:50 ganesha kernel: usbserial.c: v1.0.0:USB Serial Driver > core > Dec 20 10:49:50 ganesha kernel: usbserial.c: USB Serial support > registered for Handspring Visor > Dec 20 10:49:50 ganesha kernel: usbserial.c: Handspring Visor converter > detected > Dec 20 10:49:50 ganesha kernel: visor.c: Handspring Visor: Number of > ports: 2 > Dec 20 10:49:50 ganesha kernel: visor.c: Handspring Visor: port 1, is > for Generic use and is bound to ttyUSB0 > Dec 20 10:49:50 ganesha kernel: visor.c: Handspring Visor: port 2, is > for HotSync use and is bound to ttyUSB1 > Dec 20 10:49:50 ganesha kernel: usbserial.c: Handspring Visor converter > now attached to ttyUSB0 (or usb/tts/0 for devfs) > Dec 20 10:49:50 ganesha kernel: usbserial.c: Handspring Visor converter > now attached to ttyUSB1 (or usb/tts/1 for devfs) > Dec 20 10:49:50 ganesha kernel: visor.c: v1.0.0:USB HandSpring Visor > driver > Dec 20 10:49:50 ganesha /etc/hotplug/usb.agent: missing kernel or user > mode driver visor > Dec 20 10:49:57 ganesha kernel: usb.c: USB disconnect on device 3 > Dec 20 10:49:57 ganesha kernel: usbserial.c: Handspring Visor converter > now disconnected from ttyUSB0 > Dec 20 10:49:57 ganesha kernel: usbserial.c: Handspring Visor converter > now disconnected from ttyUSB1 > Dec 20 10:50:37 ganesha kernel: hub.c: USB new device connect on bus1/1, > assigned device number 4 > Dec 20 10:50:37 ganesha kernel: usb.c: USB new device connect, assigned > device number 4 > Dec 20 10:50:37 ganesha kernel: usbserial.c: Handspring Visor converter > detected > Dec 20 10:50:37 ganesha kernel: visor.c: Handspring Visor: Number of > ports: 2 > Dec 20 10:50:37 ganesha kernel: visor.c: Handspring Visor: port 1, is > for Generic use and is bound to ttyUSB0 > Dec 20 10:50:37 ganesha kernel: visor.c: Handspring Visor: port 2, is > for HotSync use and is bound to ttyUSB1 > Dec 20 10:50:37 ganesha kernel: usbserial.c: Handspring Visor converter > now attached to ttyUSB0 (or usb/tts/0 for devfs) > Dec 20 10:50:37 ganesha kernel: usbserial.c: Handspring Visor converter > now attached to ttyUSB1 (or usb/tts/1 for devfs) > Dec 20 10:50:37 ganesha /etc/hotplug/usb.agent: Setup visor for USB > product 82d/100/0100 > Dec 20 10:50:37 ganesha /etc/hotplug/usb.agent: missing kernel or user > mode driver visor > Dec 20 10:50:42 ganesha kernel: usb.c: USB disconnect on device 4 > Dec 20 10:50:42 ganesha kernel: usbserial.c: Handspring Visor converter > now disconnected from ttyUSB0 > Dec 20 10:50:42 ganesha kernel: usbserial.c: Handspring Visor converter > now disconnected from ttyUSB1 > > lsmod: > > Module Size Used by > visor 6828 0 (unused) > usbserial 16020 0 [visor] > irtty 5020 2 (autoclean) > irda 71341 1 (autoclean) [irtty] > tap0 2236 1 (autoclean) > lockd 42420 0 (autoclean) (unused) > sunrpc 57816 0 (autoclean) [lockd] > usb-uhci 18220 0 (unused) > usbcore 43920 1 [visor usbserial usb-uhci] > vfat 9428 2 (autoclean) > eepro100 14888 1 > nls_iso8859-8 2904 0 (unused) > nls_iso8859-15 2904 0 (unused) > nls_iso8859-1 2392 0 (unused) > nls_cp862 4152 0 (unused) > nls_cp850 3128 0 (unused) > nls_cp437 3896 4 > parport_probe 3360 0 (autoclean) > parport_pc 7276 1 (autoclean) > lp 4580 0 (unused) > parport 6852 1 [parport_probe parport_pc lp] > af_packet 6152 2 > unix 11352 76 (autoclean) > > Press hotsync button, wait two seconds, then press RETURN on this line: > bret@ganesha:~$ pilot-xfer -p /dev/ttyUSB1 -b visorbackup > > Unable to bind to port /dev/ttyUSB1 > pi_bind: Permission denied > > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > > -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
