On 4/19/20 11:58 PM, John Paul Adrian Glaubitz wrote: > ... > Some error messages would be nice. What's preventing the boot?
I don't know what's preventing the CD from booting. I don't see any error messages; the CD just doesn't seem to be a bootable device. The Debian 7.8 CD does boot. > Did you try loading GRUB directly from the OpenFirmware prompt? >From the Open Firmware prompt, the Debian 7.8 CD can be booted using the following command: 0 > boot cd:,\install\yaboot >From the Open Firmware prompt, the Debian SID CD can't be booted; I tried these commands: 0 > boot cd:,\boot\grub\powerpc.elf MAC-PARTS: can't find a default partition can't OPEN: cd:,\boot\grub\powerpc.elf 0 > boot cd:,\install\vmlinux MAC-PARTS: can't find a default partition can't OPEN: cd:,\install\vmlinux 0 > boot cd:,\install\initrd.gz MAC-PARTS: can't find a default partition can't OPEN: cd:,\install\initrd.gz Perhaps I'm not booting the right file? > >> I was able to re-install Debian 7.8 from CD; here are the ofpath and >> ofpathname results for the internal disk (/dev/sda). Hopefully this >> will be helpful in getting grub to work on this system (if it isn't >> possible to get grub to work, then I can continue to use yaboot). I >> could also re-install Debian SID from one of the pre-GRUB versions if >> you need to see the ofpath and ofpathname results from there. >> >> root@lombard:~# df / >> Filesystem 1K-blocks Used Available Use% Mounted on >> /dev/sda8 8256952 1050344 6787180 14% / >> >> root@lombard:~# ofpath /dev/sda8 >> /pci@80000000/mac-io@10/ata-3@20000/@0:8 >> >> root@lombard:~# ofpath /dev/sda >> /pci@80000000/mac-io@10/ata-3@20000/@0 >> >> root@lombard:~# ofpathname /dev/sda8 >> /pci@80000000/mac-io@10/ata-3@20000/scsi@0/sd@0,0 >> >> root@lombard:~# ofpathname /dev/sda >> /pci@80000000/mac-io@10/ata-3@20000/scsi@0/sd@0,0 > > This doesn't look like you are using the updated ofpathname version I > created but rather an outdated one. Yes, ofpath and ofpathname are the outdated versions from Debian 7.8. > > Is that by any chance the version of ofpathname shipped in Debian > Jessie? If yes, it's not surprising that the paths reported are > not correct. It's from Debian 7.8 (Wheezy). I only included the paths in case the information would be useful. I can re-install Debian SID from a pre-GRUB Debian SID CD and install your later versions of ofpathame if that would be helpful. > ... > Also, in order to fix potential issues with your particular > model, I need the output of "cat /proc/cpuinfo", "dmesg", > "lsscsi -tv" and "lspci". > > Thanks, > Adrian > The requested information is below (unfortunately, at this point it's all from Debian 7.8): ----- root@lombard:/# cat /proc/cpuinfo processor : 0 cpu : 740/750 temperature : 46-49 C (uncalibrated) clock : 399.999996MHz revision : 130.2 (pvr 0008 8202) bogomips : 33.40 timebase : 16703983 platform : PowerMac model : PowerBook1,1 machine : PowerBook1,1 motherboard : PowerBook1,1 MacRISC Power Macintosh detected as : 64 (PowerBook 101 (Lombard)) pmac flags : 00000009 L2 cache : 1024K unified pmac-generation : NewWorld Memory : 512 MB root@lombard:/# root@lombard:/# lsscsi --version version: 0.26 2012/01/31 [svn: r97] root@lombard:/# lsscsi -tv [0:0:0:0] disk ata: /dev/sda dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:10.0/0.80800000:mac-io/0.00020000:ata-3/host0/target0:0:0/0:0:0:0] [1:0:0:0] cd/dvd ata: /dev/sr0 dir: /sys/bus/scsi/devices/1:0:0:0 [/sys/devices/pci0000:00/0000:00:10.0/0.80800000:mac-io/0.00000034:media-ba/0.00021000:ata-3/host1/target1:0:0/1:0:0:0] root@lombard:/# root@lombard:/# lspci --version lspci version 3.1.9 root@lombard:/# lspci 00:00.0 Host bridge: Motorola MPC106 [Grackle] (rev 40) 00:0e.0 USB controller: LSI Corporation USB (rev 12) 00:0f.0 Multimedia controller: C-Cube Microsystems Cinemaster C 3.0 DVD Decoder (rev 02) 00:10.0 Unassigned class [ff00]: Apple Inc. Paddington Mac I/O 00:11.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI 3D Rage LT Pro (rev dc) 00:13.0 CardBus bridge: Texas Instruments PCI1211 root@lombard:/# root@lombard:/# dmesg [ 0.000000] Using PowerMac machine description [ 0.000000] Cannot reserve gpages without hugetlb enabled [ 0.000000] Total memory = 512MB; using 1024kB for hash table (at cff00000) [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.2.0-4-powerpc (debian-ker...@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 Debian 3.2.78-1 [ 0.000000] Found initrd at 0xc1400000:0xc1e6b000 [ 0.000000] Found a Paddington mac-io controller, rev: 0, mapped at 0xff780000 [ 0.000000] PowerMac motherboard: PowerBook 101 (Lombard) [ 0.000000] PMU driver v2 initialized for 1999 PowerBook G3, firmware: 0b [ 0.000000] bootconsole [udbg0] enabled [ 0.000000] Found Grackle (MPC106) PCI host bridge at 0x0000000080000000. Firmware bus number: 0->0 [ 0.000000] PCI host bridge /pci@80000000 (primary) ranges: [ 0.000000] IO 0x00000000fe000000..0x00000000fe7fffff -> 0x0000000000000000 [ 0.000000] MEM 0x00000000fd000000..0x00000000fdffffff -> 0x0000000000000000 [ 0.000000] MEM 0x0000000080000000..0x00000000fcffffff -> 0x0000000080000000 [ 0.000000] Removing ISA hole at 0x00000000fd000000 [ 0.000000] nvram: OF partition at 0x140 [ 0.000000] nvram: XP partition at 0x11b0 [ 0.000000] nvram: NR partition at 0x12b0 [ 0.000000] Top of RAM: 0x20000000, Total RAM: 0x20000000 [ 0.000000] Memory hole size: 0MB [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00020000 [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00020000 [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] free_area_init_node: node 0, pgdat c055dd10, node_mem_map c06ec000 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 130048 pages, LIFO batch:31 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: root=/dev/sda8 ro [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] High memory: 0k [ 0.000000] Memory: 500656k/524288k available (5232k kernel code, 23632k reserved, 320k data, 1512k bss, 244k init) [ 0.000000] Kernel virtual memory layout: [ 0.000000] * 0xfffcf000..0xfffff000 : fixmap [ 0.000000] * 0xff800000..0xffc00000 : highmem PTEs [ 0.000000] * 0xfeebb000..0xff800000 : early ioremap [ 0.000000] * 0xe1000000..0xfeebb000 : vmalloc & ioremap [ 0.000000] NR_IRQS:512 [ 0.000000] irq: Found primary Apple PIC /pci@80000000/mac-io@10 for 64 irqs [ 0.000000] irq: System has 64 possible interrupts [ 0.000000] GMT Delta read from XPRAM: -360 minutes, DST: on [ 0.000000] time_init: decrementer frequency = 16.703983 MHz [ 0.000000] time_init: processor frequency = 399.999996 MHz [ 0.000000] clocksource: timebase mult[ef76be9] shift[22] registered [ 0.000000] clockevent: decrementer mult[446b654] shift[32] cpu[0] [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled, bootconsole disabled [ 0.000000] pmac_zilog: serial modem detected [ 0.002444] pid_max: default: 32768 minimum: 301 [ 0.002648] Security Framework initialized [ 0.002709] AppArmor: AppArmor disabled by boot time parameter [ 0.002779] Mount-cache hash table entries: 512 [ 0.003475] device-tree: Duplicate name in /cpus/PowerPC,750@0, renamed to "l2-cache#1" [ 0.006163] Initializing cgroup subsys cpuacct [ 0.006216] Initializing cgroup subsys memory [ 0.006285] Initializing cgroup subsys devices [ 0.006308] Initializing cgroup subsys freezer [ 0.006330] Initializing cgroup subsys net_cls [ 0.006352] Initializing cgroup subsys blkio [ 0.006395] Initializing cgroup subsys perf_event [ 0.008951] devtmpfs: initialized [ 0.010516] print_constraints: dummy: [ 0.010854] NET: Registered protocol family 16 [ 0.012275] PMU i2c /pci@80000000/mac-io@10/via-pmu@16000 [ 0.012314] channel 1 bus <multibus> [ 0.012338] channel 2 bus <multibus> [ 0.012844] PCI: Probing PCI hardware [ 0.013127] pci 0000:00:00.0: [1057:0002] type 0 class 0x000600 [ 0.013274] pci 0000:00:0e.0: [11c1:5801] type 0 class 0x000c03 [ 0.013310] pci 0000:00:0e.0: reg 10: [mem 0x80882000-0x80882fff] [ 0.013407] pci 0000:00:0f.0: [123f:8888] type 0 class 0x000480 [ 0.013436] pci 0000:00:0f.0: reg 10: [io 0x0c00-0x0cff] [ 0.013549] pci 0000:00:10.0: [106b:0017] type 0 class 0x00ff00 [ 0.013575] pci 0000:00:10.0: reg 10: [mem 0x80800000-0x8087ffff] [ 0.013672] pci 0000:00:11.0: [1002:4c49] type 0 class 0x000300 [ 0.013703] pci 0000:00:11.0: reg 10: [mem 0x81000000-0x81ffffff] [ 0.013726] pci 0000:00:11.0: reg 14: [io 0x0c00-0x0cff] [ 0.013748] pci 0000:00:11.0: reg 18: [mem 0x80881000-0x80881fff] [ 0.013790] pci 0000:00:11.0: reg 30: [mem 0x00000000-0x0001ffff pref] [ 0.013833] pci 0000:00:11.0: supports D1 D2 [ 0.013893] pci 0000:00:13.0: [104c:ac1e] type 2 class 0x000607 [ 0.013923] pci 0000:00:13.0: reg 10: [mem 0x80880000-0x80880fff] [ 0.013966] pci 0000:00:13.0: supports D1 D2 [ 0.013981] pci 0000:00:13.0: PME# supported from D0 D1 D2 D3hot [ 0.014168] pci 0000:00:13.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.015309] PCI: Cannot allocate resource region 1 of device 0000:00:11.0, will remap [ 0.015374] PCI 0000:00 Cannot reserve Legacy IO [io 0x0000-0x0fff] [ 0.015391] PCI: max bus depth: 1 pci_try_num: 2 [ 0.015447] pci 0000:00:11.0: BAR 6: assigned [mem 0x80000000-0x8001ffff pref] [ 0.015496] pci 0000:00:11.0: BAR 1: assigned [io 0x1000-0x10ff] [ 0.015537] pci 0000:00:13.0: BAR 16: assigned [mem 0x84000000-0x87ffffff] [ 0.015578] pci 0000:00:13.0: BAR 15: assigned [mem 0x88000000-0x8bffffff pref] [ 0.015624] pci 0000:00:13.0: BAR 14: assigned [io 0x1100-0x11ff] [ 0.015661] pci 0000:00:13.0: BAR 13: assigned [io 0x1200-0x12ff] [ 0.015698] pci 0000:00:13.0: CardBus bridge to [bus 01-04] [ 0.015731] pci 0000:00:13.0: bridge window [io 0x1200-0x12ff] [ 0.015767] pci 0000:00:13.0: bridge window [io 0x1100-0x11ff] [ 0.015804] pci 0000:00:13.0: bridge window [mem 0x88000000-0x8bffffff pref] [ 0.015850] pci 0000:00:13.0: bridge window [mem 0x84000000-0x87ffffff] [ 0.015904] pci 0000:00:13.0: enabling device (0000 -> 0003) [ 0.015948] pci_bus 0000:00: resource 0 [io 0x0000-0x7fffff] [ 0.015965] pci_bus 0000:00: resource 1 [mem 0x80000000-0xfcffffff] [ 0.015982] pci_bus 0000:01: resource 0 [io 0x1200-0x12ff] [ 0.015998] pci_bus 0000:01: resource 1 [io 0x1100-0x11ff] [ 0.016014] pci_bus 0000:01: resource 2 [mem 0x88000000-0x8bffffff pref] [ 0.016032] pci_bus 0000:01: resource 3 [mem 0x84000000-0x87ffffff] [ 0.019748] bio: create slab <bio-0> at 0 [ 0.020414] vgaarb: device added: PCI:0000:00:11.0,decodes=io+mem,owns=mem,locks=none [ 0.020469] vgaarb: loaded [ 0.020489] vgaarb: bridge control possible 0000:00:11.0 [ 0.021065] SCSI subsystem initialized [ 0.021335] libata version 3.00 loaded. [ 0.022099] Switching to clocksource timebase [ 0.044122] NET: Registered protocol family 2 [ 0.056341] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.057466] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.058600] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.059179] TCP: Hash tables configured (established 16384 bind 16384) [ 0.059221] TCP reno registered [ 0.059251] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.059320] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.059821] NET: Registered protocol family 1 [ 0.114276] PCI: CLS 32 bytes, default 32 [ 0.114673] Unpacking initramfs... [ 1.515954] Freeing initrd memory: 10668k freed [ 1.519717] Thermal assist unit using timers, shrink_timer: 500 jiffies [ 1.522226] audit: initializing netlink socket (disabled) [ 1.522346] type=2000 audit(1587388694.520:1): initialized [ 1.583081] VFS: Disk quotas dquot_6.5.2 [ 1.583243] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.583478] msgmni has been set to 1000 [ 1.584419] alg: No test for stdrng (krng) [ 1.584604] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.584657] io scheduler noop registered [ 1.584682] io scheduler deadline registered [ 1.584745] io scheduler cfq registered (default) [ 1.585305] atyfb 0000:00:11.0: enabling device (0086 -> 0087) [ 1.585370] atyfb: using auxiliary register aperture [ 1.585800] atyfb: 3D RAGE LT PRO (Mach64 LI, PCI) [0x4c49 rev 0xdc] [ 1.585877] atyfb: 8M SDRAM (1:1), 29.498928 MHz XTAL, 230 MHz PLL, 100 Mhz MCLK, 100 MHz XCLK [ 1.586472] atyfb: monitor sense=62b, mode 6 [ 1.649857] Console: switching to colour frame buffer device 128x48 [ 1.669346] atyfb: fb0: ATY Mach64 frame buffer device on PCI [ 1.670592] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.672056] pmac_zilog: 0.6 (Benjamin Herrenschmidt <b...@kernel.crashing.org>) [ 1.672399] ttyPZ0 at MMIO 0x80813020 (irq = 16) is a Z85c30 ESCC - Internal modem [ 1.672978] ttyPZ1 at MMIO 0x80813000 (irq = 17) is a Z85c30 ESCC - Infrared port [ 1.673544] Serial: MPC52xx PSC UART driver [ 1.673921] Generic non-volatile memory driver v1.1 [ 1.674337] Linux agpgart interface v0.103 [ 1.674703] MacIO PCI driver attached to Paddington chipset [ 1.675865] Can't request resource 0 for MacIO device 0.00000000:power-mg [ 1.677682] swim3 0.00015000:fdc: [fd0] SWIM3 floppy controller in media bay [ 1.679937] mediabay0: Registered Heathrow media-bay [ 1.882971] PMU Backlight initialized (pmubl) [ 1.884077] mediabay0: Bay contains an ATA device [ 1.884311] adb: starting probe task... [ 2.902181] pata-macio 0.00020000:ata-3: Activating pata-macio chipset Heathrow ATA, Apple bus ID 0 [ 2.903573] scsi0 : pata_macio [ 2.904105] ata1: PATA max MWDMA2 irq 25 [ 3.066740] ata1.00: ATA-6: ST9120821A, 3.04, max UDMA/100 [ 3.066980] ata1.00: 234441648 sectors, multi 8: LBA48 [ 3.083325] ata1.00: configured for MWDMA2 [ 3.084193] scsi 0:0:0:0: Direct-Access ATA ST9120821A 3.04 PQ: 0 ANSI: 5 [ 3.922173] pata-macio 0.00021000:ata-3: Activating pata-macio chipset Heathrow ATA, Apple bus ID 1 [ 3.933485] scsi1 : pata_macio [ 3.943940] ata2: PATA max MWDMA2 irq 36 [ 3.954713] mousedev: PS/2 mouse device common for all mice [ 3.968541] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0 [ 3.980041] TCP cubic registered [ 3.990485] NET: Registered protocol family 10 [ 4.003426] Mobile IPv6 [ 4.013212] NET: Registered protocol family 17 [ 4.023187] Registering the dns_resolver key type [ 4.033826] PM: Hibernation image not present or could not be loaded. [ 4.033891] registered taskstats version 1 [ 4.048975] rtc-generic rtc-generic: setting system clock to 2020-04-20 07:18:17 UTC (1587367097) [ 4.058952] Initializing network drop monitor service [ 4.114672] ata2.00: ATAPI: MATSHITADVD-ROM SR-8174, C113, max UDMA/33 [ 4.133240] adb devices: [2]: 2 c3 [ 4.139638] ata2.00: configured for MWDMA2 [ 4.149779] [3]: 3 1 [7]: 7 1f [ 4.164227] scsi 1:0:0:0: CD-ROM MATSHITA DVD-ROM SR-8174 C113 PQ: 0 ANSI: 5 [ 4.177332] Freeing unused kernel memory: 244k freed [ 4.191444] ADB keyboard at 2, handler 1 [ 4.210307] Detected ADB keyboard, type ANSI. [ 4.210692] input: ADB keyboard as /devices/virtual/input/input0 [ 4.210999] input: ADB Powerbook buttons as /devices/virtual/input/input1 [ 4.249061] ADB mouse at 3, handler set to 4 (trackpad) [ 4.326685] input: ADB mouse as /devices/virtual/input/input2 [ 4.345633] adb: finished probe task... [ 4.377032] udevd[47]: starting version 175 [ 4.546403] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen [ 4.556564] ata2: mediabay plug [ 4.566431] ata2: soft resetting link [ 4.767729] usbcore: registered new interface driver usbfs [ 5.330217] mesh: configured for synchronous 5 MB/s [ 5.365246] eth0: BMAC+ at 00:50:e4:45:95:32 [ 5.400865] usbcore: registered new interface driver hub [ 5.463383] usbcore: registered new device driver usb [ 5.569085] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB) [ 5.593938] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.614732] sd 0:0:0:0: [sda] Write Protect is off [ 5.624649] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.654329] mesh: performing initial bus reset... [ 5.668549] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.794728] ata2.00: configured for MWDMA2 [ 5.805042] sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 [ 5.815498] ata2: EH complete [ 5.832740] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.850616] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray [ 5.860996] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 5.872886] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.897073] ohci_hcd 0000:00:0e.0: OHCI Host Controller [ 5.912114] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 5.924423] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 5.928653] ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 1 [ 5.942979] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 5.974454] ohci_hcd 0000:00:0e.0: irq 28, io mem 0x80882000 [ 6.078416] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 6.088787] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.098982] usb usb1: Product: OHCI Host Controller [ 6.109156] usb usb1: Manufacturer: Linux 3.2.0-4-powerpc ohci_hcd [ 6.119389] usb usb1: SerialNumber: 0000:00:0e.0 [ 6.131528] hub 1-0:1.0: USB hub found [ 6.141808] hub 1-0:1.0: 2 ports detected [ 9.666257] scsi2 : MESH [ 9.697317] scsi: waiting for bus probes to complete ... [ 12.083414] PM: Starting manual resume from disk [ 12.093365] PM: Hibernation image partition 8:12 present [ 12.093377] PM: Looking for hibernation image. [ 12.109762] PM: Image not found (code -22) [ 12.109777] PM: Hibernation image not present or could not be loaded. [ 12.218003] kjournald starting. Commit interval 5 seconds [ 12.228276] EXT3-fs (sda8): mounted filesystem with ordered data mode [ 15.159163] udevd[273]: starting version 175 [ 16.236102] yenta_cardbus 0000:00:13.0: CardBus bridge found [0000:0000] [ 16.247256] yenta_cardbus 0000:00:13.0: Enabling burst memory read transactions [ 16.258475] yenta_cardbus 0000:00:13.0: Using CSCINT to route CSC interrupts to PCI [ 16.269489] yenta_cardbus 0000:00:13.0: Routing CardBus interrupts to PCI [ 16.280365] yenta_cardbus 0000:00:13.0: TI: mfunc 0x00000002, devctl 0x60 [ 16.297467] PowerMac i2c bus pmu 2 registered [ 16.446554] PowerMac i2c bus pmu 1 registered [ 16.566416] yenta_cardbus 0000:00:13.0: ISA IRQ mask 0x0000, PCI irq 22 [ 16.577450] yenta_cardbus 0000:00:13.0: Socket status: 30000086 [ 16.715596] yenta_cardbus 0000:00:13.0: pcmcia: parent PCI bridge window: [io 0x0000-0x7fffff] [ 16.814710] yenta_cardbus 0000:00:13.0: pcmcia: parent PCI bridge window: [mem 0x80000000-0xfcffffff] [ 16.873784] pcmcia_socket pcmcia_socket0: cs: memory probe 0x80000000-0xfcffffff: excluding 0x80000000-0x81ffffff 0x84000000-0x8bffffff [ 17.096830] pcmcia_socket pcmcia_socket0: cs: memory probe 0x80000000-0x80ffffff: excluding 0x80000000-0x800fffff 0x80800000-0x808fffff [ 20.454023] Adding 2097148k swap on /dev/sda12. Priority:-1 extents:1 across:2097148k [ 21.348654] EXT3-fs (sda8): using internal journal [ 21.785423] loop: module loaded [ 23.233212] input: PowerMac Beep as /devices/pci0000:00/0000:00:10.0/input/input3 [ 29.463986] phy registers: [ 29.465315] 0800 7849 2000 5c10 01e1 c5e1 000f 2801 [ 29.486742] 0000 0000 0000 0000 0000 0000 0000 0000 [ 29.507808] 2002 0000 0000 0000 0001 0000 0020 0000 [ 29.528585] 0000 0000 0180 0100 0006 0f00 0000 0000 [ 30.170025] RPC: Registered named UNIX socket transport module. [ 30.180380] RPC: Registered udp transport module. [ 30.190716] RPC: Registered tcp transport module. [ 30.200936] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 30.358437] FS-Cache: Loaded [ 30.693484] FS-Cache: Netfs 'nfs' registered for caching [ 30.786129] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 37.188955] Bluetooth: Core ver 2.16 [ 37.189407] NET: Registered protocol family 31 [ 37.189633] Bluetooth: HCI device and connection manager initialized [ 37.189923] Bluetooth: HCI socket layer initialized [ 37.190205] Bluetooth: L2CAP socket layer initialized [ 37.192653] Bluetooth: SCO socket layer initialized [ 37.235697] Bluetooth: RFCOMM TTY layer initialized [ 37.236140] Bluetooth: RFCOMM socket layer initialized [ 37.236412] Bluetooth: RFCOMM ver 1.11 [ 37.266282] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 37.266683] Bluetooth: BNEP filters: protocol multicast [ 37.643225] lp: driver loaded but no devices found [ 40.210173] eth0: no IPv6 routers present [ 42.910303] input: Mouseemu virtual keyboard as /devices/virtual/input/input4 [ 42.918404] input: Mouseemu virtual mouse as /devices/virtual/input/input5
