-------- Original-Nachricht -------- > Datum: Sat, 04 Jun 2011 10:33:31 +0800 > Von: Bear <jiling...@gmail.com> > An: Gerhard Pircher <gerhard_pirc...@gmx.net> > CC: debian-powerpc@lists.debian.org > Betreff: Re: Can I install debian on a e300 board?
> hi, > Thanks for your help and I have successfully run my custom kernel on my > board via loading a fdt file: > > U-Boot 1.3.0 (Dec 22 2008 - 11:19:29) MPC83XX > > Reset Status: > > CPU: e300c3, MPC8313E, Rev: 21 at 333.333 MHz, CSB: 166 MHz > Board: Freescale MPC8313ERDB > I2C: ready > DRAM: 128 MB > FLASH: 8 MB > NAND: 32 MiB > In: serial > Out: serial > Err: serial > Net: TSEC0, TSEC1 [PRIME] > Hit any key to stop autoboot: 0 > => > => setenv serverip 192.168.0.104 > => setenv loadaddr 0x01000000 > => setenv fdtaddr 0x02000000 > => dhcp > Speed: 100, full duplex > BOOTP broadcast 1 > DHCP client bound to address 192.168.0.103 > Using TSEC1 device > TFTP from server 192.168.0.104; our IP address is 192.168.0.103 > Filename 'uImage'. > Load address: 0x1000000 > Loading: ################################################################# > > ################################################################# > ######## > done > Bytes transferred = 2021460 (1ed854 hex) > => tftp 0x02000000 mpc8313erdb.dtb > Speed: 100, full duplex > Using TSEC1 device > TFTP from server 192.168.0.104; our IP address is 192.168.0.103 > Filename 'mpc8313erdb.dtb'. > Load address: 0x2000000 > Loading: # > done > Bytes transferred = 7721 (1e29 hex) > => bootm 0x01000000 - 0x02000000 > ## Booting image at 01000000 ... > Image Name: Linux-2.6.39.1 > Created: 2011-06-03 16:24:13 UTC > Image Type: PowerPC Linux Kernel Image (gzip compressed) > Data Size: 2021396 Bytes = 1.9 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Uncompressing Kernel Image ... OK > Booting using the fdt at 0x2000000 > Loading Device Tree to 007fd000, end 007fee28 ... OK > Using MPC831x RDB machine description > Linux version 2.6.39.1 (bear@debian) (gcc version 4.4.5 (Debian 4.4.5-8) > ) #1 Fri Jun 3 23:40:59 CST 2011 > bootconsole [udbg0] enabled > setup_arch: bootmem > mpc831x_rdb_setup_arch() > Found FSL PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0 > PCI host bridge /sleep-nexus/pci@e0008500 (primary) ranges: > MEM 0x0000000090000000..0x000000009fffffff -> 0x0000000090000000 > MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 > Prefetch > IO 0x00000000e2000000..0x00000000e20fffff -> 0x0000000000000000 > arch: exit > Zone PFN ranges: > DMA 0x00000000 -> 0x00008000 > Normal empty > Movable zone start PFN for each node > early_node_map[1] active PFN ranges > 0: 0x00000000 -> 0x00008000 > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 > Kernel command line: root=/dev/ram console=ttyS0,115200 > PID hash table entries: 512 (order: -1, 2048 bytes) > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) > Memory: 124524k/131072k available (4080k kernel code, 6548k reserved, > 148k data, 1107k bss, 184k init) > Kernel virtual memory layout: > * 0xfffdf000..0xfffff000 : fixmap > * 0xfdefb000..0xfe000000 : early ioremap > * 0xc9000000..0xfdefb000 : vmalloc & ioremap > SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 > NR_IRQS:512 nr_irqs:512 16 > IPIC (128 IRQ sources) at c9000700 > clocksource: timebase mult[6000002] shift[22] registered > pid_max: default: 32768 minimum: 301 > Mount-cache hash table entries: 512 > NET: Registered protocol family 16 > > PCI: Probing PCI hardware > bio: create slab <bio-0> at 0 > vgaarb: loaded > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > Switching to clocksource timebase > Switched to NOHz mode on CPU #0 > NET: Registered protocol family 2 > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) > TCP established hash table entries: 4096 (order: 3, 32768 bytes) > TCP bind hash table entries: 4096 (order: 2, 16384 bytes) > TCP: Hash tables configured (established 4096 bind 4096) > TCP reno registered > UDP hash table entries: 256 (order: 0, 4096 bytes) > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) > NET: Registered protocol family 1 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > RPC: Registered tcp NFSv4.1 backchannel transport module. > JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc. > msgmni has been set to 245 > io scheduler noop registered > io scheduler deadline registered > io scheduler cfq registered (default) > Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled > serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 16) is a 16550A > console [ttyS0] enabled, bootconsole disabled > console [ttyS0] enabled, bootconsole disabled > serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 17) is a 16550A > brd: module loaded > loop: module loaded > fe000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer > ID 0x000001 Chip ID 0x001001 > Amd/Fujitsu Extended Query Table at 0x0040 > Amd/Fujitsu Extended Query version 1.3. > fe000000.flash: Swapping erase regions for top-boot CFI table. > number of CFI chips: 1 > cmdlinepart partition parsing not available > RedBoot partition parsing not available > fsl-lbc e0005000.localbus: read_byte beyond end of buffer > fsl-lbc e0005000.localbus: read_byte beyond end of buffer > fsl-lbc e0005000.localbus: read_byte beyond end of buffer > NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB > 3,3V 8-bit) > cmdlinepart partition parsing not available > RedBoot partition parsing not available > Creating 3 MTD partitions on "e2800000.flash": > 0x000000000000-0x000000100000 : "u-boot" > 0x000000100000-0x000000400000 : "kernel" > 0x000000400000-0x000002000000 : "fs" > eLBC NAND device at 0xe2800000, bank 1 > Fixed MDIO Bus: probed > fsl-gianfar e0024000.ethernet: enabled errata workarounds, flags: 0x7 > eth0: Gianfar Ethernet Controller Version 1.2, 04:00:00:00:00:0a > eth0: Running with NAPI enabled > eth0: RX BD ring size for Q[0]: 256 > eth0: TX BD ring size for Q[0]: 256 > fsl-gianfar e0025000.ethernet: enabled errata workarounds, flags: 0x7 > eth1: Gianfar Ethernet Controller Version 1.2, 04:00:00:00:00:0b > eth1: Running with NAPI enabled > eth1: RX BD ring size for Q[0]: 256 > eth1: TX BD ring size for Q[0]: 256 > Freescale PowerQUICC MII Bus: probed > Freescale PowerQUICC MII Bus: probed > e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI > e100: Copyright(c) 1999-2006 Intel Corporation > usbmon: debugfs is not available > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > uhci_hcd: USB Universal Host Controller Interface driver > /soc8313@e0000000/usb@23000: Invalid 'dr_mode' property, fallback to > host mode > fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller > fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 > fsl-ehci fsl-ehci.0: irq 38, io mem 0xe0023000 > fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > i2c /dev entries driver > mpc-i2c e0003000.i2c: timeout 1000000 us > rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0 > mpc-i2c e0003100.i2c: timeout 1000000 us > md: linear personality registered for level -1 > md: raid0 personality registered for level 0 > md: raid1 personality registered for level 1 > TCP cubic registered > NET: Registered protocol family 17 > Registering the dns_resolver key type > rtc-ds1307 0-0068: setting system clock to 2000-01-03 15:08:10 UTC > (946912090) > md: Waiting for all devices to be available before autodetect > md: If you don't use raid, use raid=noautodetect > md: Autodetecting RAID arrays. > md: Scanned 0 and added 0 devices. > md: autorun ... > md: ... autorun DONE. > List of all partitions: > 1f00 8192 mtdblock0 (driver?) > 1f01 1024 mtdblock1 (driver?) > 1f02 3072 mtdblock2 (driver?) > 1f03 28672 mtdblock3 (driver?) > No filesystem could mount root, tried: ext3 ext2 > Kernel panic - not syncing: VFS: Unable to mount root fs on > unknown-block(1,0) > Rebooting in 180 seconds.. > > But unfortunately, it seems like the kernel still need a rootfs? I have > a SD card and I wanna install debian into it. Is there anyone who can > tell me how to do? Thanks. I don't know, if your board has a specific SD/MMC card controller, but you could try to enable "MMC_SPI" or "MMC_SDHCI_OF" with "make menuconfig". > BTW: The official installer in Business Card CD seems not work with me: > U-Boot 1.3.0 (Dec 22 2008 - 11:19:29) MPC83XX > > Reset Status: > > CPU: e300c3, MPC8313E, Rev: 21 at 333.333 MHz, CSB: 166 MHz > Board: Freescale MPC8313ERDB > I2C: ready > DRAM: 128 MB > FLASH: 8 MB > NAND: 32 MiB > In: serial > Out: serial > Err: serial > Net: TSEC0, TSEC1 [PRIME] > Hit any key to stop autoboot: 0 > => setenv serverip 192.168.0.104 > => setenv fdtaddr 0x02000000 > => setenv loadaddr 0x01000000 > => dhcp > Speed: 100, full duplex > BOOTP broadcast 1 > DHCP client bound to address 192.168.0.103 > Using TSEC1 device > TFTP from server 192.168.0.104; our IP address is 192.168.0.103 > Filename 'uImage'. > Load address: 0x1000000 > Loading: ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > #################### > done > Bytes transferred = 6967619 (6a5143 hex) > => tftp 0x02000000 mpc8313erdb.my.dtb > Speed: 100, full duplex > Using TSEC1 device > TFTP from server 192.168.0.104; our IP address is 192.168.0.103 > Filename 'mpc8313erdb.my.dtb'. > Load address: 0x2000000 > Loading: # > done > Bytes transferred = 7721 (1e29 hex) > => bootm 0x01000000 - 0x02000000 > ## Booting image at 01000000 ... > Image Name: Debian-businesscard-squeeze > Created: 2011-06-03 11:37:07 UTC > Image Type: PowerPC Linux Kernel Image (uncompressed) > Data Size: 6967555 Bytes = 6.6 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > OK > Booting using the fdt at 0x2000000 > Loading Device Tree to 007fd000, end 007fee28 ... OK > > and it hang. As I mentioned before, the platform support/setup code for your board isn't compiled into the Debian kernel. Thus the kernel can't identify the "compatible = "MPC8313ERDB", "MPC831xRDB", "MPC83xxRDB";" property in the device tree for your board. Gerhard -- NEU: FreePhone - kostenlos mobil telefonieren! Jetzt informieren: http://www.gmx.net/de/go/freephone -- To UNSUBSCRIBE, email to debian-powerpc-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20110604113858.28...@gmx.net
