On Fri, Nov 05, 2004 at 11:07:42PM +0100, Niklaus Giger wrote: > Hi > > I downloaded the special pegasos 1 netinst iso at : > > > http://people.debian.org/~luther/pegasos/sarge-pegasos1-netinst-2004.10.25.iso > > In the OF-prompt I typed > boot /pci/ide/[EMAIL PROTECTED],0 PEGASOS1.;1 > as my CD-Rom-drive is the primary master. Then I get after about 20 seconds > lines like: > >chrpboot starting > >initial ramdisk > >gunzipping > >heap consumed > >start adddress > >calling quiesce > >return 0x0 from prom_init > afterwards I get stucked and even after 120 seconds there is no Linux boot > prompt. I have a ATI radeon 9200 AGP card which is identified by lspci as > follows: > 0000:01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 SE] > (Secondary) (rev 01) > My wh0000:00:00.0 Host bridge: Mai Logic Incorporated Articia S Host Bridge > (rev 01) > 0000:00:01.0 PCI bridge: Mai Logic Incorporated Articia S PCI Bridge > 0000:00:06.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host > Controller (rev 46) > 0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] > (rev 10) > 0000:00:07.1 IDE interface: VIA Technologies, Inc. > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) > 0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 1e) > 0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 1e) > 0000:00:07.4 Non-VGA unclassified device: VIA Technologies, Inc. VT8235 ACPI > (rev 10) > 0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 > AC97 > Audio Controller (rev 40) > 0000:00:07.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 > Modem] (rev 20) > 0000:00:08.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] > (rev 51) > 0000:00:0b.0 Unknown mass storage controller: Silicon Image, Inc. (formerly > CMD Technology Inc) PCI0680 Ultra ATA-133Host Controller (rev 02) > 0000:00:0c.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] > (rev 86) > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon > 9200 SE] (rev 01) > 0000:01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 SE] > (Secondary) (rev 01) > pole lspci returns:
Strange, should work fine. Can you manage to capture the serial output ? This may tell us more about it. What kind of pegasos 1 do you have ? Which version of the openfirmware have you on it ? > I never managed to compile a bootable kernel from the official debian > kernel-source-2.6.8 even when I took a .config from a working kernel made > from the gentoo 2.6.8-pegasos-r2 sources. And I had always the same problem, > that the kernel just never continued after the prom_init. Without the serial log output, not much. It works on my pegasos 1 here. Friendly, Sven Luther
