On Mon, 2014-01-13 at 13:54 +0100, Sylvain LEVEQUE wrote: > I upgraded a QNAP TS-119 from linux-image-3.11-2-kirkwood to > linux-image-3.12-1-kirkwood. > dpkg.log states: > 2014-01-06 14:37:08 upgrade linux-image-kirkwood:armel 3.11+54 3.12+55 > > On the next reboot, the NAS was stuck early. I gave it a whole > afternoon to boot, initially thinking an fsck was going on (which can > take some time on a slow CPU with a large drive). I used the recovery > console to get more information and instructions from > http://cyrius.com/debian/kirkwood/qnap/ts-119/uboot/ to get back to > normal, by reflashing linux-image-3.11-2-kirkwood over the failing > 3.12. > > I suspect http://comments.gmane.org/gmane.linux.debian.ports.arm/13582 > to be the same issue on a close hardware.
So do I (ccing Hardy). > Here is the boot log from the console: Thanks. Sadly it (as you can see) just silently hangs after the kernel decompressor :-( I've had a look at the linux-arm-kernel list for any recent reports along these lines but I didn't see anything. Apparently earlyprintk is enabled in our kirkwood kernels -- could you try adding "earlyprintk" to your kernel command line args please. Unless that gives us any clues then I think the next step is to take this to the upstream l-a-k list. I suppose it would be worth trying 3.13 from experimental first though. Ian. > > __ __ _ _ > | \/ | __ _ _ ____ _____| | | > | |\/| |/ _` | '__\ \ / / _ \ | | > | | | | (_| | | \ V / __/ | | > |_| |_|\__,_|_| \_/ \___|_|_| > _ _ ____ _ > | | | | | __ ) ___ ___ | |_ > | | | |___| _ \ / _ \ / _ \| __| > | |_| |___| |_) | (_) | (_) | |_ > \___/ |____/ \___/ \___/ \__| ** LOADER ** > ** MARVELL BOARD: DB-88F6281A-BP LE > > U-Boot 1.1.4 (Feb 9 2009 - 11:13:32) Marvell version: 3.4.4 > > U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC > > Soc: 88F6281 A0 (DDR2) > CPU running @ 1200Mhz L2 running @ 400Mhz > SysClock = 400Mhz , TClock = 200Mhz > > DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 > DRAM CS[0] base 0x00000000 size 256MB > DRAM CS[1] base 0x10000000 size 256MB > DRAM Total size 512MB 16bit width > [16384kB@f8000000] Flash: 16 MB > Addresses 8M - 0M are saved for the U-Boot usage. > Mem malloc Initialization (8M - 7M): Done > > CPU : Marvell Feroceon (Rev 1) > > Streaming disabled > Write allocate disabled > > > USB 0: host mode > PEX 0: interface detected no Link. > Net: egiga0 [PRIME] > > Marvell Serial ATA Adapter > Integrated Sata device found > [0 0 0]: Enable DMA mode > Device 0 @ 0 0: > Model: WDC WD10EADS-00L5B1 Firm: 01.01A01 Ser#: > WD-WCAU4D159618 > Type: Hard Disk > Supports 48-bit addressing > Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) > > Hit any key to stop autoboot: 0 > ## Booting image at 00800000 ... > Image Name: kernel 3.12-1-kirkwood > Created: 2014-01-12 12:05:37 UTC > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 1929800 Bytes = 1.8 MB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > OK > > Starting kernel ... > > Uncompressing Linux... done, booting the kernel. > > > > Thank you > -- > Sylvain > > > -- System Information: > Debian Release: jessie/sid > APT prefers testing > APT policy: (990, 'testing'), (50, 'unstable'), (40, 'experimental') > Architecture: armel (armv5tel) > > Kernel: Linux 3.11-2-kirkwood > Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8) > Shell: /bin/sh linked to /bin/dash > > -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/1389624807.13654.69.ca...@kazak.uk.xensource.com
