Package: linux Version: 3.12.6-2 Severity: important Dear Maintainer,
I upgraded a QNAP TS-119 from linux-image-3.11-2-kirkwood to linux-image-3.12-1-kirkwood. dpkg.log states: 2014-01-06 14:37:08 upgrade linux-image-kirkwood:armel 3.11+54 3.12+55 On the next reboot, the NAS was stuck early. I gave it a whole afternoon to boot, initially thinking an fsck was going on (which can take some time on a slow CPU with a large drive). I used the recovery console to get more information and instructions from http://cyrius.com/debian/kirkwood/qnap/ts-119/uboot/ to get back to normal, by reflashing linux-image-3.11-2-kirkwood over the failing 3.12. I suspect http://comments.gmane.org/gmane.linux.debian.ports.arm/13582 to be the same issue on a close hardware. Here is the boot log from the console: __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Feb 9 2009 - 11:13:32) Marvell version: 3.4.4 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width [16384kB@f8000000] Flash: 16 MB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode Device 0 @ 0 0: Model: WDC WD10EADS-00L5B1 Firm: 01.01A01 Ser#: WD-WCAU4D159618 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Hit any key to stop autoboot: 0 ## Booting image at 00800000 ... Image Name: kernel 3.12-1-kirkwood Created: 2014-01-12 12:05:37 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1929800 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Thank you -- Sylvain -- System Information: Debian Release: jessie/sid APT prefers testing APT policy: (990, 'testing'), (50, 'unstable'), (40, 'experimental') Architecture: armel (armv5tel) Kernel: Linux 3.11-2-kirkwood Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20140113125440.3244.31844.report...@donkeykong.gromi.net
