Package: linux-image-2.6.26-2-amd64
Version: 2.6.26-19
Severity: important
Modules amd64_agp and agpgart not found in
/lib/modules/2.6.26-2-amd64/kernel/drivers/char/agp/.
Xorg unable to use agp and disables dri.
The only way to use dri is to set the bus type to pci in xorg.conf.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-amd64 (Debian 2.6.26-19) (da...@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Aug 19 22:33:18 UTC
2009
** Command line:
root=/dev/mapper/debian-root ro
** Tainted: G M (16)
** Kernel log:
[ 7.035152] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 7.056375] hda: Host Protected Area detected.
[ 7.056375] current capacity is 488395055 sectors (250058 MB)
[ 7.056375] native capacity is 488397168 sectors (250059 MB)
[ 7.171878] hda: Host Protected Area disabled.
[ 7.172374] hda: 488397168 sectors (250059 MB) w/16384KiB Cache,
CHS=30401/255/63
[ 7.196373] hda: cache flushes supported
[ 7.196497] hda: hda1
[ 7.220507] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[ 7.220507] Uniform CD-ROM driver Revision: 3.20
[ 7.372924] device-mapper: uevent: version 1.0.3
[ 7.373409] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised:
dm-de...@redhat.com
[ 7.545733] PM: Starting manual resume from disk
[ 7.593359] kjournald starting. Commit interval 5 seconds
[ 7.593359] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.697483] udevd version 125 started
[ 9.399080] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
[ 9.399080] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2000
[ 9.502588] usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid
0x04E8 pid 0x3268
[ 9.502654] usbcore: registered new interface driver usblp
[ 9.541554] input: Power Button (FF) as /class/input/input2
[ 9.604170] ACPI: Power Button (FF) [PWRF]
[ 9.604290] input: Power Button (CM) as /class/input/input3
[ 9.652165] ACPI: Power Button (CM) [PWRB]
[ 9.786777] usb-storage: device scan complete
[ 9.786777] scsi 2:0:0:0: Direct-Access WD 7500AAV External 1.75
PQ: 0 ANSI: 4
[ 9.790779] sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156
MB)
[ 9.790779] sd 2:0:0:0: [sdc] Write Protect is off
[ 9.790779] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 9.790779] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 9.790779] sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156
MB)
[ 9.790794] sd 2:0:0:0: [sdc] Write Protect is off
[ 9.790830] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 9.790832] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 9.790869] sdc: sdc1
[ 9.806781] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 9.958696] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 9.966242] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 10.178684] input: PC Speaker as /class/input/input4
[ 10.219660] gameport: EMU10K1 is pci0000:02:09.1/gameport0, io 0xb400, speed
1196kHz
[ 10.234395] logips2pp: Detected unknown logitech mouse model 89
[ 10.462342] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 10.462388] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17
(level, low) -> IRQ 17
[ 10.708408] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input5
[ 11.543941] EXT3 FS on dm-1, internal journal
[ 12.416373] loop: module loaded
[ 12.438809] it87: Found IT8712F chip at 0x290, revision 5
[ 14.838788] kjournald starting. Commit interval 5 seconds
[ 14.838788] EXT3 FS on sda1, internal journal
[ 14.838788] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.906233] kjournald starting. Commit interval 5 seconds
[ 14.914361] EXT3 FS on dm-0, internal journal
[ 14.914424] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.961676] kjournald starting. Commit interval 5 seconds
[ 14.966368] EXT3 FS on dm-6, internal journal
[ 14.966429] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.990358] kjournald starting. Commit interval 5 seconds
[ 15.006474] EXT3 FS on dm-2, internal journal
[ 15.006533] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.030358] kjournald starting. Commit interval 5 seconds
[ 15.038493] EXT3 FS on dm-3, internal journal
[ 15.038552] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.066471] kjournald starting. Commit interval 5 seconds
[ 15.074801] EXT3 FS on dm-4, internal journal
[ 15.074861] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.206470] Adding 2998264k swap on /dev/mapper/debian-swapp_00.
Priority:-1 extents:1 across:2998264k
[ 16.968988] skge eth0: enabling interface
[ 18.043424] NET: Registered protocol family 10
[ 18.043542] lo: Disabled Privacy Extensions
[ 18.044110] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.728007] skge eth0: Link is up at 100 Mbps, full duplex, flow control both
[ 18.728319] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.234688] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor
3800+ processors (2 cpu cores) (version 2.20.00)
[ 19.234688] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8
[ 19.234688] powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12
[ 21.743871] Clocksource tsc unstable (delta = -191404840 ns)
[ 22.463573] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 22.463579] vboxdrv: Successfully done.
[ 22.463582] vboxdrv: Found 2 processor cores.
[ 22.463613] VBoxDrv: dbg - g_abExecMemory=ffffffffa030b980
[ 22.463655] vboxdrv: fAsync=1 offMin=0x11d170 offMax=0x11d170
[ 22.463732] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is
'normal'.
[ 22.463758] vboxdrv: Successfully loaded version 3.0.4 (interface
0x000e0000).
[ 22.696270] VBoxNetFlt: dbg - g_abExecMemory=ffffffffa04a7900
[ 22.719552] VBoxNetAdp: dbg - g_abExecMemory=ffffffffa04bf5e0
[ 24.914872] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 27.818893] [drm] Initialized drm 1.1.0 20060810
[ 27.828773] ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
[ 27.828784] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC5] -> GSI 16
(level, low) -> IRQ 16
[ 27.828861] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[ 29.493642] eth0: no IPv6 routers present
[ 29.617641] [drm] Setting GART location based on new memory map
[ 29.673790] [drm] Loading R200 Microcode
[ 29.673826] [drm] writeback test succeeded in 1 usecs
[ 1360.364885] kjournald starting. Commit interval 5 seconds
[ 1360.364885] EXT3-fs warning: maximal mount count reached, running e2fsck is
recommended
[ 1360.385940] EXT3 FS on sdc1, internal journal
[ 1360.385940] EXT3-fs: recovery complete.
[ 1360.390141] EXT3-fs: mounted filesystem with ordered data mode.
[ 3331.967462] rhythmbox[3983] trap stack segment ip:7f679df880d2
sp:7fffac87cc90 error:0
** Loaded modules:
Module Size Used by
radeon 133920 2
drm 91488 3 radeon
vboxnetadp 88364 0
vboxnetflt 94700 0
vboxdrv 1698316 1 vboxnetflt
powernow_k8 17156 1
cpufreq_conservative 11784 0
cpufreq_powersave 6400 0
cpufreq_stats 9120 0
cpufreq_ondemand 11792 1
freq_table 9344 3 powernow_k8,cpufreq_stats,cpufreq_ondemand
cpufreq_userspace 8452 0
ipv6 288456 22
it87 28952 0
hwmon_vid 7296 1 it87
loop 19468 0
snd_emu10k1_synth 10752 0
snd_emux_synth 36864 1 snd_emu10k1_synth
snd_seq_virmidi 10112 1 snd_emux_synth
snd_seq_midi_emul 10496 1 snd_emux_synth
snd_emu10k1 141152 4 snd_emu10k1_synth
snd_seq_midi 11072 0
snd_seq_midi_event 11904 2 snd_seq_virmidi,snd_seq_midi
snd_rawmidi 26784 3 snd_seq_virmidi,snd_emu10k1,snd_seq_midi
firmware_class 12544 1 snd_emu10k1
snd_ac97_codec 115416 1 snd_emu10k1
ac97_bus 6272 1 snd_ac97_codec
snd_pcm 81800 4 snd_emu10k1,snd_ac97_codec
snd_page_alloc 13072 2 snd_emu10k1,snd_pcm
snd_util_mem 8960 2 snd_emux_synth,snd_emu10k1
snd_hwdep 12040 2 snd_emux_synth,snd_emu10k1
snd_seq 54304 5
snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_midi,snd_seq_midi_event
snd_timer 25744 3 snd_emu10k1,snd_pcm,snd_seq
snd_seq_device 11668 6
snd_emu10k1_synth,snd_emux_synth,snd_emu10k1,snd_seq_midi,snd_rawmidi,snd_seq
snd 63688 14
snd_emux_synth,snd_seq_virmidi,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_hwdep,snd_seq,snd_timer,snd_seq_device
emu10k1_gp 7552 0
pcspkr 7040 0
gameport 17040 2 emu10k1_gp
soundcore 12064 1 snd
psmouse 42268 0
serio_raw 9988 0
k8temp 9216 0
shpchp 34208 0
pci_hotplug 32056 1 shpchp
button 11680 0
usblp 16896 0
i2c_nforce2 10752 0
i2c_core 27936 1 i2c_nforce2
evdev 14208 3
ext3 125072 8
jbd 51240 1 ext3
mbcache 12804 1 ext3
dm_mirror 20608 0
dm_log 13956 1 dm_mirror
dm_snapshot 19400 0
dm_mod 58864 18 dm_mirror,dm_log,dm_snapshot
ide_cd_mod 36360 0
cdrom 37928 1 ide_cd_mod
ide_disk 16512 0
sd_mod 29376 7
usb_storage 95936 1
ide_pci_generic 9220 0 [permanent]
amd74xx 13448 0 [permanent]
ide_core 128284 4 ide_cd_mod,ide_disk,ide_pci_generic,amd74xx
floppy 61672 0
ata_generic 10116 0
skge 41744 0
sata_nv 28680 3
ehci_hcd 36108 0
libata 165600 2 ata_generic,sata_nv
scsi_mod 161016 3 sd_mod,usb_storage,libata
dock 14112 1 libata
ohci_hcd 25092 0
thermal 22688 0
processor 42304 2 powernow_k8,thermal
fan 9352 0
thermal_sys 17728 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: nVidia Corporation nForce3 250Gb Host Bridge
[10de:00e1] (rev a1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=32M]
Capabilities: <access denied>
00:01.0 ISA bridge [0601]: nVidia Corporation nForce3 250Gb LPC Bridge
[10de:00e0] (rev a2)
Subsystem: Giga-byte Technology Device [1458:0c11]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation nForce 250Gb PCI System Management
[10de:00e4] (rev a1)
Subsystem: Giga-byte Technology Device [1458:0c11]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at e800 [size=32]
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at 2000 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:02.0 USB Controller [0c03]: nVidia Corporation CK8S USB Controller
[10de:00e7] (rev a1) (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f6002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.1 USB Controller [0c03]: nVidia Corporation CK8S USB Controller
[10de:00e7] (rev a1) (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at f6003000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.2 USB Controller [0c03]: nVidia Corporation nForce3 EHCI USB 2.0
Controller [10de:00e8] (rev a2) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 20
Region 0: Memory at f6004000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:08.0 IDE interface [0101]: nVidia Corporation CK8S Parallel ATA Controller
(v2.5) [10de:00e5] (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Device [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
Kernel modules: amd74xx, ide-pci-generic, ata_generic
00:0a.0 IDE interface [0101]: nVidia Corporation nForce3 Serial ATA Controller
[10de:00e3] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at e000 [size=16]
Region 5: I/O ports at e400 [size=128]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: ide-pci-generic, sata_nv, ata_generic
00:0b.0 PCI bridge [0604]: nVidia Corporation nForce3 250Gb AGP Host to PCI
Bridge [10de:00e2] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: f2000000-f3ffffff
Prefetchable memory behind bridge: e0000000-efffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:0e.0 PCI bridge [0604]: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge
[10de:00ed] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=128
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: f4000000-f5ffffff
Prefetchable memory behind bridge: c4000000-c40fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV280 [Radeon
9200 PRO] [1002:5960] (rev 01) (prog-if 00 [VGA controller])
Subsystem: Club-3D BV Device [196d:1050]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at a000 [size=256]
Region 2: Memory at f3000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at f2000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: radeonfb
01:00.1 Display controller [0380]: ATI Technologies Inc RV280 [Radeon 9200 PRO]
(Secondary) [1002:5940] (rev 01)
Subsystem: Club-3D BV Device [196d:1051]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at f3010000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
02:09.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1
[1102:0002] (rev 0a)
Subsystem: Creative Labs SBLive! 5.1 Digital Model SB0220 [1102:8065]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b000 [size=32]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
Kernel modules: snd-emu10k1
02:09.1 Input device controller [0980]: Creative Labs SB Live! Game Port
[1102:7002] (rev 0a)
Subsystem: Creative Labs Gameport Joystick [1102:0020]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: I/O ports at b400 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
Kernel modules: emu10k1-gp
02:0b.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001
Gigabit Ethernet Controller [11ab:4320] (rev 13)
Subsystem: Giga-byte Technology Marvell 88E8001 Gigabit Ethernet
Controller (Gigabyte) [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at b800 [size=256]
[virtual] Expansion ROM at c4000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: skge
Kernel modules: skge
-- System Information:
Debian Release: 5.0.3
APT prefers proposed-updates
APT policy: (500, 'proposed-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=es_ES.UTF-8, LC_CTYPE=es_ES.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-2-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-2-amd64 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-amd64/postinst/bootloader-error-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/lilo-initrd-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/depmod-error-2.6.26-2-amd64: false
linux-image-2.6.26-2-amd64/postinst/old-dir-initrd-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/create-kimage-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/preinst/initrd-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-amd64/preinst/abort-install-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/postinst/old-initrd-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/depmod-error-initrd-2.6.26-2-amd64: false
linux-image-2.6.26-2-amd64/postinst/bootloader-test-error-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/overwriting-modules-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-amd64/preinst/failed-to-move-modules-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/prerm/would-invalidate-boot-loader-2.6.26-2-amd64:
true
linux-image-2.6.26-2-amd64/postinst/old-system-map-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/preinst/abort-overwrite-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/bootloader-initrd-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/preinst/elilo-initrd-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/prerm/removing-running-kernel-2.6.26-2-amd64: true
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
