On Fri, Aug 27, 2004 at 02:48:18PM +0200, Sven Luther wrote: > Benh, just so you are in the loop. > > Friendly, > > Sven Luther > > On Fri, Aug 27, 2004 at 11:45:07AM +0200, Francesco P. Lovergine wrote: > > Package: kernel > > Severity: normal > > > > 2.4 series radeonfb (1.8-benh) works perfectly (also modular). > > 2.6 series new radeonfb never worked (since 2.6.0 at least), it does not > > sync here (laptop XSVGA). > > After loading, fbset reports 1400x1050-60, as for the 2.4 version, but > > screen > > is blank and stay in normal text mode 80x25. I need to switch on and back > > to X in order to > > see screen content again. That's for loading it modular of course, I have > > to do yet test > > for static version. > > > > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon > > Mobility M6 LY > > > > 0000:01:00.0 0300: 1002:4c59 > > Subsystem: 0e11:b11b > > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop+ ParErr- > > Stepping+ SERR+ FastB2B+ > > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Interrupt: pin A routed to IRQ 9 > > Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] > > Region 1: I/O ports at 2000 [size=256] > > Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K] > > Expansion ROM at <unassigned> [disabled] [size=128K] > > Capabilities: <available only to root> > > > > In dmesg: > > > > Aug 18 19:06:41 localhost kernel: radeonfb: Retreived PLL infos from BIOS > > Aug 18 19:06:41 localhost kernel: radeonfb: Reference=27.00 MHz (RefDiv=60) > > Memory=166.00 Mhz, System=143.00 MHz > > Aug 18 19:06:42 localhost kernel: radeonfb: Monitor 1 type LCD found > > Aug 18 19:06:42 localhost kernel: radeonfb: EDID probed > > Aug 18 19:06:42 localhost kernel: radeonfb: Monitor 2 type no found > > Aug 18 19:06:42 localhost kernel: radeonfb: panel ID string: Samsung > > LTN150P1-L02 > > Aug 18 19:06:42 localhost kernel: radeonfb: detected LVDS panel size from > > BIOS: 1400x1050 > > Aug 18 19:06:42 localhost kernel: radeondb: BIOS provided dividers will be > > used > > Aug 18 19:06:42 localhost kernel: radeonfb: Power Management enabled for > > Mobility chipsets > > Aug 18 19:06:42 localhost kernel: radeonfb: ATI Radeon LY DDR SGRAM 32 MB > > > > This is with current 2.6.8 in debian, but that's true with _all_ other > > previous versions (2.6.0+). > > > > fbset return right mode, as set in /etc/fb.modes too: > > > > mode "1400x1050-60" > > # D: 108.003 MHz, H: 63.983 kHz, V: 60.191 Hz > > geometry 1400 1050 1400 1050 8 > > timings 9259 136 40 10 0 112 3 > > rgba 6/0,6/0,6/0,0/0 > > hsync high > > vsync high > > accel true > > endmode > > > > I tried to fbset explicitly the mode after module loading too, but without > > results. > > I'll return results with static compiled in module when possible. > >
Ok, I tried with radeonfb statically compiled in. Same results. Display images disappeared a few messages after boot and reappeared later (in 80x25) when console fonts are loaded, I think. fbset again return a 1400x1050-60 mode active... -- Francesco P. Lovergine
