dmesg
---------------------------
[ 1.005427] NET: Registered protocol family 17
[ 1.005432] Registering the dns_resolver key type
[ 1.005455] Using IPI No-Shortcut mode
[ 1.005555] PM: Hibernation image not present or could not be loaded.
[ 1.005566] registered taskstats version 1
[ 1.006134] rtc_cmos 00:09: setting system clock to 2014-08-05
11:13:15 UTC (1407237195)
[ 1.006198] Initializing network drop monitor service
[ 1.006292] Freeing unused kernel memory: 420k freed
[ 1.006517] Write protecting the kernel text: 2860k
[ 1.006553] Write protecting the kernel read-only data: 1084k
[ 1.006555] NX-protecting the kernel data: 3284k
[ 1.020072] udevd[44]: starting version 175
[ 1.026013] input: AT Translated Set 2 keyboard
as /devices/platform/i8042/serio0/input/input0
[ 1.095723] tg3.c:v3.121 (November 2, 2011)
[ 1.095759] tg3 0000:10:00.0: setting latency timer to 64
[ 1.106802] usbcore: registered new interface driver usbfs
[ 1.106832] usbcore: registered new interface driver hub
[ 1.127895] sdhci: Secure Digital Host Controller Interface driver
[ 1.127900] sdhci: Copyright(c) Pierre Ossman
[ 1.156094] usbcore: registered new device driver usb
[ 1.156617] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[ 1.156676] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.156681] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.156711] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 1
[ 1.156744] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.160619] ehci_hcd 0000:00:1d.7: cache line size of 64 is not
supported
[ 1.171924] SCSI subsystem initialized
[ 1.193723] sdhci-pci 0000:02:06.4: SDHCI controller found
[104c:8034] (rev 0)
[ 1.193805] mmc0: no vmmc regulator found
[ 1.193843] Registered led device: mmc0::
[ 1.196046] mmc0: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.196072] mmc1: no vmmc regulator found
[ 1.196108] Registered led device: mmc1::
[ 1.197138] mmc1: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.197157] mmc2: no vmmc regulator found
[ 1.197185] Registered led device: mmc2::
[ 1.198211] mmc2: SDHCI controller on PCI [0000:02:06.4] using PIO
[ 1.206544] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.228950] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xc8500000
[ 1.268102] libata version 3.00 loaded.
[ 1.274815] tg3 0000:10:00.0: eth0: Tigon3 [partno(BCM95751M) rev
4101] (PCI Express) MAC address 00:15:60:bc:25:8a
[ 1.274822] tg3 0000:10:00.0: eth0: attached PHY is 5750
(10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[ 1.274826] tg3 0000:10:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0]
ASF[0] TSOcap[1]
[ 1.274830] tg3 0000:10:00.0: eth0: dma_rwctrl[76180000]
dma_mask[64-bit]
[ 1.296037] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.296104] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002
[ 1.296108] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.296111] usb usb1: Product: EHCI Host Controller
[ 1.296114] usb usb1: Manufacturer: Linux 3.2.0-4-686-pae ehci_hcd
[ 1.296117] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.296266] hub 1-0:1.0: USB hub found
[ 1.296272] hub 1-0:1.0: 8 ports detected
[ 1.296409] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.296414] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.296424] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 2
[ 1.296455] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00003000
[ 1.296492] usb usb2: New USB device found, idVendor=1d6b,
idProduct=0001
[ 1.296496] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.296499] usb usb2: Product: UHCI Host Controller
[ 1.296501] usb usb2: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[ 1.296504] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.296627] hub 2-0:1.0: USB hub found
[ 1.296633] hub 2-0:1.0: 2 ports detected
[ 1.296723] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.296728] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.296737] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 3
[ 1.296780] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00003020
[ 1.296816] usb usb3: New USB device found, idVendor=1d6b,
idProduct=0001
[ 1.296820] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.296823] usb usb3: Product: UHCI Host Controller
[ 1.296825] usb usb3: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[ 1.296828] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.296952] hub 3-0:1.0: USB hub found
[ 1.296957] hub 3-0:1.0: 2 ports detected
[ 1.297038] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.297043] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.297051] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 4
[ 1.297087] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
[ 1.297124] usb usb4: New USB device found, idVendor=1d6b,
idProduct=0001
[ 1.297127] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.297130] usb usb4: Product: UHCI Host Controller
[ 1.297133] usb usb4: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[ 1.297136] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.297256] hub 4-0:1.0: USB hub found
[ 1.297262] hub 4-0:1.0: 2 ports detected
[ 1.297615] ata_piix 0000:00:1f.1: version 2.13
[ 1.297672] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.302920] scsi0 : ata_piix
[ 1.305423] scsi1 : ata_piix
[ 1.366375] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x3580
irq 14
[ 1.366380] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x3588
irq 15
[ 1.371887] ata2: port disabled--ignoring
[ 1.396756] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.396760] ACPI: Thermal Zone [TZ1] (43 C)
[ 1.396858] ACPI: Fan [C255] (off)
[ 1.396935] ACPI: Fan [C256] (off)
[ 1.397008] ACPI: Fan [C257] (off)
[ 1.397082] ACPI: Fan [C258] (off)
[ 1.450291] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.450295] ACPI: Thermal Zone [TZ2] (43 C)
[ 1.458867] thermal LNXTHERM:02: registered as thermal_zone2
[ 1.458871] ACPI: Thermal Zone [TZ3] (16 C)
[ 1.462579] thermal LNXTHERM:03: registered as thermal_zone3
[ 1.462582] ACPI: Thermal Zone [TZ4] (38 C)
[ 1.531129] ata1.00: ATA-6: HTS541060G9AT00, MB3OA60A, max UDMA/100
[ 1.531133] ata1.00: 117210240 sectors, multi 16: LBA
[ 1.531141] ata1.01: ATAPI: UJDA765aDVD/CDRW, 1.02, max MWDMA2
[ 1.544528] ata1.00: configured for UDMA/100
[ 1.560361] ata1.01: configured for MWDMA2
[ 1.560733] scsi 0:0:0:0: Direct-Access ATA HTS541060G9AT00
MB3O PQ: 0 ANSI: 5
[ 1.562429] scsi 0:0:1:0: CD-ROM MATSHITA UJDA765aDVD/CDRW
1.02 PQ: 0 ANSI: 5
[ 1.570608] Refined TSC clocksource calibration: 1862.048 MHz.
[ 1.570615] Switching to clocksource tsc
[ 1.589444] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda
tray
[ 1.589448] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.591666] sd 0:0:0:0: [sda] 117210240 512-byte logical blocks:
(60.0 GB/55.8 GiB)
[ 1.591816] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 1.593323] sd 0:0:0:0: [sda] Write Protect is off
[ 1.593328] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.593352] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.640042] sda: sda1 sda2 < sda5 >
[ 1.645519] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.650727] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.650810] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 1.880015] usb 3-2: new full-speed USB device number 2 using
uhci_hcd
[ 1.999575] PM: Starting manual resume from disk
[ 1.999579] PM: Hibernation image partition 8:5 present
[ 1.999581] PM: Looking for hibernation image.
[ 1.999787] PM: Image not found (code -22)
[ 1.999790] PM: Hibernation image not present or could not be loaded.
[ 2.014846] EXT4-fs (sda1): INFO: recovery required on readonly
filesystem
[ 2.014851] EXT4-fs (sda1): write access will be enabled during
recovery
[ 2.048820] usb 3-2: New USB device found, idVendor=03f0,
idProduct=011d
[ 2.048824] usb 3-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 2.048828] usb 3-2: Product: HP integrated Bluetooth module
[ 2.048830] usb 3-2: Manufacturer: Broadcom
[ 5.578203] EXT4-fs (sda1): orphan cleanup on readonly fs
[ 5.578216] EXT4-fs (sda1): ext4_orphan_cleanup: deleting
unreferenced inode 1837333
[ 5.578317] EXT4-fs (sda1): ext4_orphan_cleanup: deleting
unreferenced inode 1994961
[ 5.578355] EXT4-fs (sda1): 2 orphan inodes deleted
[ 5.578358] EXT4-fs (sda1): recovery complete
[ 5.693476] EXT4-fs (sda1): mounted filesystem with ordered data
mode. Opts: (null)
[ 7.661817] udevd[353]: starting version 175
[ 8.645347] wmi: Mapper loaded
[ 8.703502] ACPI: Requesting acpi_cpufreq
[ 8.704213] input: Video Bus
as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input1
[ 8.704222] ACPI: Video Device [C0FA] (multi-head: yes rom: no
post: no)
[ 8.705413] ACPI: AC Adapter [C176] (on-line)
[ 8.705593] input: Sleep Button
as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 8.705599] ACPI: Sleep Button [C1F2]
[ 8.705668] input: Lid Switch
as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[ 8.705706] ACPI: Lid Switch [C1F3]
[ 8.705785] ACPI: Battery Slot [C178] (battery absent)
[ 8.705870] ACPI: Battery Slot [C177] (battery absent)
[ 8.708457] tpm_inf_pnp 00:05: Found C1BB with ID IFX0101
[ 8.708509] tpm_inf_pnp 00:05: TPM found: config base 0x560, data
base 0x570, chip version 0x0006, vendor id 0x15d1 (Infineon), product id
0x0006 (SLD 9630 TT 1.1)
[ 8.711892] Marking TSC unstable due to TSC halts in idle
[ 8.711911] ACPI: acpi_idle registered with cpuidle
[ 8.712367] input: Power Button
as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 8.712375] ACPI: Power Button [PWRF]
[ 8.718666] Switching to clocksource hpet
[ 8.880995] intel_rng: FWH not detected
[ 9.206891] input: PC Speaker
as /devices/platform/pcspkr/input/input5
[ 9.234451] input: HP WMI hotkeys as /devices/virtual/input/input6
[ 9.340970] [drm] Initialized drm 1.1.0 20060810
[ 9.351129] parport_pc 00:04: reported by Plug and Play ACPI
[ 9.351205] parport0: PC-style at 0x378 (0x778), irq 7
[PCSPP,TRISTATE]
[ 9.448953] yenta_cardbus 0000:02:06.0: CardBus bridge found
[103c:0944]
[ 9.448983] yenta_cardbus 0000:02:06.0: Enabling burst memory read
transactions
[ 9.448995] yenta_cardbus 0000:02:06.0: Using INTVAL to route CSC
interrupts to PCI
[ 9.449002] yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to
PCI
[ 9.449014] yenta_cardbus 0000:02:06.0: TI: mfunc 0x01111b22, devctl
0x64
[ 9.521272] iTCO_vendor_support: vendor-support=0
[ 9.522961] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 9.524329] iTCO_wdt: Found a ICH6-M TCO device (Version=2,
TCOBASE=0x1060)
[ 9.525142] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 9.604471] cfg80211: Calling CRDA to update world regulatory domain
[ 9.623839] lib80211: common routines for IEEE802.11 drivers
[ 9.623843] lib80211_crypt: registered algorithm 'NULL'
[ 9.684718] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0c78, PCI irq
18
[ 9.684729] yenta_cardbus 0000:02:06.0: Socket status: 30000006
[ 9.684739] pci_bus 0000:02: Raising subordinate bus# of parent bus
(#02) from #03 to #06
[ 9.684757] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge
window: [io 0x4000-0x4fff]
[ 9.684766] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x4000-0x4fff: excluding 0x4000-0x40ff 0x4400-0x44ff
[ 9.691509] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge
window: [mem 0xc8100000-0xc83fffff]
[ 9.691520] pcmcia_socket pcmcia_socket0: cs: memory probe
0xc8100000-0xc83fffff: excluding 0xc8100000-0xc812ffff
[ 9.691568] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge
window: [mem 0x80000000-0x83ffffff pref]
[ 9.691577] pcmcia_socket pcmcia_socket0: cs: memory probe
0x80000000-0x83ffffff: excluding 0x80000000-0x83ffffff
[ 9.779660] libipw: 802.11 data/management/control stack, git-1.1.13
[ 9.779664] libipw: Copyright (C) 2004-2005 Intel Corporation
<jketr...@linux.intel.com>
[ 9.794440] psmouse serio4: synaptics: Touchpad model: 1, fw: 6.2,
id: 0x25a0b1, caps: 0xa04793/0x300000/0x0
[ 9.794452] psmouse serio4: synaptics: serio: Synaptics pass-through
port at isa0060/serio4/input0
[ 9.798046] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver,
1.2.2kmprq
[ 9.798052] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 9.798243] ipw2200: Detected Intel PRO/Wireless 2200BG Network
Connection
[ 9.838169] input: SynPS/2 Synaptics TouchPad
as /devices/platform/i8042/serio4/input/input7
[ 9.870833] NET: Registered protocol family 23
[ 9.968964] found SMC SuperIO Chip (devid=0x7a rev=00 base=0x004e):
LPC47N227
[ 9.968993] smsc_superio_flat(): fir: 0x100, sir: 0x3e8, dma: 03,
irq: 3, mode: 0x0e
[ 9.969004] smsc_ircc_present: can't get sir_base of 0x3e8
[ 10.314579] ipw2200 0000:02:04.0: firmware: agent loaded
ipw2200-bss.fw into memory
[ 10.458002] ipw2200: Detected geography ZZM (11 802.11bg channels, 0
802.11a channels)
[ 10.636319] Non-volatile memory driver v1.3
[ 10.744755] [drm] radeon kernel modesetting enabled.
[ 10.745104] radeon 0000:01:00.0: setting latency timer to 64
[ 10.745115] [drm] initializing kernel modesetting (RV380
0x1002:0x5460 0x103C:0x0944).
[ 10.745135] [drm] register mmio base: 0xC8400000
[ 10.745137] [drm] register mmio size: 65536
[ 10.745363] [drm] Generation 2 PCI interface, using max accessible
memory
[ 10.745369] radeon 0000:01:00.0: VRAM: 128M 0x00000000C0000000 -
0x00000000C7FFFFFF (64M used)
[ 10.745373] radeon 0000:01:00.0: GTT: 512M 0x00000000A0000000 -
0x00000000BFFFFFFF
[ 10.746080] [drm] Detected VRAM RAM=128M, BAR=128M
[ 10.746084] [drm] RAM width 64bits DDR
[ 10.746242] [TTM] Zone kernel: Available graphics memory: 444402 kiB
[ 10.746245] [TTM] Zone highmem: Available graphics memory: 1037206
kiB
[ 10.746248] [TTM] Initializing pool allocator
[ 10.746255] [TTM] Initializing DMA pool allocator
[ 10.746287] [drm] radeon: 64M of VRAM memory ready
[ 10.746290] [drm] radeon: 512M of GTT memory ready.
[ 10.746311] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 10.747298] [drm] radeon: ib pool ready.
[ 10.747375] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[ 10.748902] [drm] PCIE GART of 512M enabled (table at
0x00000000C0040000).
[ 10.748941] radeon 0000:01:00.0: WB enabled
[ 10.748945] [drm] fence driver on ring 0 use gpu addr 0xa0000000 and
cpu addr 0xffbca000
[ 10.748950] [drm] Supports vblank timestamp caching Rev 1
(10.10.2010).
[ 10.748952] [drm] Driver supports precise vblank timestamp query.
[ 10.749070] radeon 0000:01:00.0: irq 43 for MSI/MSI-X
[ 10.749083] radeon 0000:01:00.0: radeon: using MSI.
[ 10.749110] [drm] radeon: irq initialized.
[ 10.749753] [drm] Loading R300 Microcode
[ 10.867334] platform radeon_cp.0: firmware: agent loaded
radeon/R300_cp.bin into memory
[ 10.867722] [drm] radeon: ring at 0x00000000A0001000
[ 10.867747] [drm] ring test succeeded in 1 usecs
[ 10.868070] [drm] ib test succeeded in 0 usecs
[ 10.868512] [drm] Panel ID String: SEC
[ 10.868519] [drm] Panel Size 1024x768
[ 10.879585] [drm] radeon legacy LVDS backlight initialized
[ 10.881068] [drm] Radeon Display Connectors
[ 10.881074] [drm] Connector 0:
[ 10.881078] [drm] VGA
[ 10.881085] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 10.881090] [drm] Encoders:
[ 10.881095] [drm] CRT1: INTERNAL_DAC1
[ 10.881099] [drm] Connector 1:
[ 10.881103] [drm] DVI-D
[ 10.881107] [drm] HPD1
[ 10.881113] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 10.881118] [drm] Encoders:
[ 10.881122] [drm] DFP1: INTERNAL_TMDS1
[ 10.881127] [drm] Connector 2:
[ 10.881131] [drm] LVDS
[ 10.881137] [drm] DDC: 0x68 0x68 0x68 0x68 0x68 0x68 0x68 0x68
[ 10.881142] [drm] Encoders:
[ 10.881146] [drm] LCD1: INTERNAL_LVDS
[ 10.881151] [drm] Connector 3:
[ 10.881155] [drm] S-video
[ 10.881158] [drm] Encoders:
[ 10.881162] [drm] TV1: INTERNAL_DAC2
[ 10.881268] [drm] radeon: power management initialized
[ 10.901326] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x37f
[ 10.903074] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x3e0-0x4ff: excluding 0x3e8-0x3ff 0x4d0-0x4d7
[ 10.903768] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x820-0x8ff: clean.
[ 10.904737] pcmcia_socket pcmcia_socket0: cs: IO port probe
0xc00-0xcf7: clean.
[ 10.905399] pcmcia_socket pcmcia_socket0: cs: memory probe
0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xe0000-0xfffff
[ 10.905437] pcmcia_socket pcmcia_socket0: cs: memory probe
0xa0000000-0xa0ffffff: clean.
[ 10.905471] pcmcia_socket pcmcia_socket0: cs: memory probe
0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[ 10.905505] pcmcia_socket pcmcia_socket0: cs: IO port probe
0xa00-0xaff: clean.
[ 10.965891] [drm] fb mappable at 0xC00C0000
[ 10.965894] [drm] vram apper at 0xC0000000
[ 10.965896] [drm] size 3145728
[ 10.965898] [drm] fb depth is 24
[ 10.965900] [drm] pitch is 4096
[ 10.966024] fbcon: radeondrmfb (fb0) is primary device
[ 11.009255] Console: switching to colour frame buffer device 128x48
[ 11.014899] fb0: radeondrmfb frame buffer device
[ 11.014902] drm: registered panic notifier
[ 11.026500] [drm] Initialized radeon 2.16.0 20080528 for 0000:01:00.0
on minor 0
[ 11.078594] snd_intel8x0 0000:00:1e.2: power state changed by ACPI to
D0
[ 11.078601] snd_intel8x0 0000:00:1e.2: power state changed by ACPI to
D0
[ 11.078641] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[ 11.606630] cfg80211: World regulatory domain updated:
[ 11.606638] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 11.606646] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 11.606654] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 11.606690] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
(N/A, 2000 mBm)
[ 11.606697] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz),
(N/A, 2000 mBm)
[ 11.606714] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 2000 mBm)
[ 11.606722] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000
KHz), (N/A, 0 mBm)
[ 11.727929] Bluetooth: Core ver 2.16
[ 11.727972] NET: Registered protocol family 31
[ 11.727978] Bluetooth: HCI device and connection manager initialized
[ 11.727985] Bluetooth: HCI socket layer initialized
[ 11.727991] Bluetooth: L2CAP socket layer initialized
[ 11.728559] Bluetooth: SCO socket layer initialized
[ 11.765231] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 11.814170] usbcore: registered new interface driver btusb
[ 12.004037] intel8x0_measure_ac97_clock: measured 55246 usecs (2662
samples)
[ 12.004045] intel8x0: clocking to 48000
[ 12.005630] snd_intel8x0m 0000:00:1e.3: setting latency timer to 64
[ 14.226469] Adding 2421756k swap on /dev/sda5. Priority:-1 extents:1
across:2421756k
[ 14.247810] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 14.513204] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 14.631386] loop: module loaded
[ 15.649343] input: PS/2 Generic Mouse
as /devices/platform/i8042/serio4/serio5/input/input8
[ 16.919432] RPC: Registered named UNIX socket transport module.
[ 16.919436] RPC: Registered udp transport module.
[ 16.919438] RPC: Registered tcp transport module.
[ 16.919440] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 16.979863] FS-Cache: Loaded
[ 17.058377] FS-Cache: Netfs 'nfs' registered for caching
[ 17.085036] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 19.094598] input: ACPI Virtual Keyboard Device
as /devices/virtual/input/input9
[ 21.321807] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.774478] lib80211_crypt: registered algorithm 'CCMP'
[ 24.159838] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 24.159846] Bluetooth: BNEP filters: protocol multicast
[ 24.160516] Bluetooth: RFCOMM TTY layer initialized
[ 24.160526] Bluetooth: RFCOMM socket layer initialized
[ 24.160531] Bluetooth: RFCOMM ver 1.11
[ 25.423190] lp0: using parport0 (interrupt-driven).
[ 25.566055] ppdev: user-space parallel port driver
[ 33.600023] eth1: no IPv6 routers present
[ 42.187567] postgres (3206): /proc/3206/oom_adj is deprecated, please
use /proc/3206/oom_score_adj instead.
[ 2932.014617] ata1: drained 8 bytes to clear DRQ
[ 2932.014625] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
frozen
[ 2932.014629] ata1.01: ATAPI check failed (ireason=0x2 bytes=0)
[ 2932.014639] sr 0:0:1:0: CDB: Get event status notification: 4a 01 00
00 10 00 00 00 08 00
[ 2932.014654] ata1.01: cmd a0/00:00:00:08:00/00:00:00:00:00/b0 tag 29
pio 16392 in
[ 2932.014655] res 58/00:02:00:08:00/00:00:00:00:00/b0 Emask
0x2 (HSM violation)
[ 2932.014659] ata1.01: status: { DRDY DRQ }
[ 2932.014689] ata1: soft resetting link
[ 2932.216766] ata1.00: configured for UDMA/100
[ 2932.232474] ata1.01: configured for MWDMA2
[ 2932.232798] ata1: EH complete
[29055.867589] PM: Syncing filesystems ... done.
[29055.870048] PM: Preparing system for mem sleep
[29056.088852] Freezing user space processes ... (elapsed 0.01 seconds)
done.
[29056.104084] Freezing remaining freezable tasks ... (elapsed 0.01
seconds) done.
[29056.120073] PM: Entering mem sleep
[29056.120087] Suspending console(s) (use no_console_suspend to debug)
[29056.261693] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[29056.261822] sd 0:0:0:0: [sda] Stopping disk
[29056.311787] tpm_inf_pnp 00:05: saving TPM state
[29056.316610] parport_pc 00:04: disabled
[29056.317091] serial 00:02: disabled
[29056.320222] ACPI handle has no context!
[29056.320233] ACPI handle has no context!
[29056.320245] eth1: Going into suspend...
[29056.832067] radeon 0000:01:00.0: Refused to change power state,
currently in D0
[29056.832090] PM: suspend of devices complete after 711.832 msecs
[29056.832365] ehci_hcd 0000:00:1d.7: wake-up capability enabled by ACPI
[29056.848124] uhci_hcd 0000:00:1d.2: wake-up capability enabled by ACPI
[29056.848181] uhci_hcd 0000:00:1d.1: wake-up capability enabled by ACPI
[29056.848237] uhci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[29056.848270] PM: late suspend of devices complete after 16.176 msecs
[29056.848836] ACPI: Preparing to enter system sleep state S3
[29056.848964] PM: Saving platform NVS memory
[29056.849031] Disabling non-boot CPUs ...
[29056.849031] ACPI: Low-level resume complete
[29056.849031] PM: Restoring platform NVS memory
[29056.849031] Force enabled HPET at resume
[29056.849135] ACPI: Waking up from system sleep state S3
[29057.004245] uhci_hcd 0000:00:1d.0: wake-up capability disabled by
ACPI
[29057.004309] uhci_hcd 0000:00:1d.1: wake-up capability disabled by
ACPI
[29057.004370] uhci_hcd 0000:00:1d.2: wake-up capability disabled by
ACPI
[29057.004421] ehci_hcd 0000:00:1d.7: wake-up capability disabled by
ACPI
[29057.005237] PM: early resume of devices complete after 1.301 msecs
[29057.005385] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[29057.005411] usb usb2: root hub lost power or was reset
[29057.005429] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[29057.005452] usb usb3: root hub lost power or was reset
[29057.005469] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[29057.005493] usb usb4: root hub lost power or was reset
[29057.005512] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[29057.005539] pci 0000:00:1e.0: setting latency timer to 64
[29057.005547] snd_intel8x0 0000:00:1e.2: power state changed by ACPI to
D0
[29057.005552] snd_intel8x0 0000:00:1e.2: power state changed by ACPI to
D0
[29057.005558] snd_intel8x0 0000:00:1e.2: power state changed by ACPI to
D0
[29057.005562] snd_intel8x0 0000:00:1e.2: power state changed by ACPI to
D0
[29057.005574] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[29057.005608] snd_intel8x0m 0000:00:1e.3: setting latency timer to 64
[29057.005647] ata_piix 0000:00:1f.1: setting latency timer to 64
[29057.005666] radeon 0000:01:00.0: setting latency timer to 64
[29057.005675] radeon 0000:01:00.0: f7358e00 unpin not necessary
[29057.175432] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[29057.175447] eth1: Coming out of suspend...
[29057.179022] ata2: port disabled--ignoring
[29057.348027] sd 0:0:0:0: [sda] Starting disk
[29057.353586] [drm] PCIE GART of 512M enabled (table at
0x00000000C0040000).
[29057.353596] radeon 0000:01:00.0: WB enabled
[29057.353599] [drm] fence driver on ring 0 use gpu addr 0xa0000000 and
cpu addr 0xffbca000
[29057.353643] [drm] radeon: ring at 0x00000000A0001000
[29057.353662] [drm] ring test succeeded in 1 usecs
[29057.360140] [drm] ib test succeeded in 0 usecs
[29057.528069] serial 00:02: activated
[29057.529858] parport_pc 00:04: activated
[29057.668036] usb 3-2: reset full-speed USB device number 2 using
uhci_hcd
[29057.871543] btusb 3-2:1.0: no reset_resume for driver btusb?
[29057.871546] btusb 3-2:1.1: no reset_resume for driver btusb?
[29059.904518] ata1.01: ACPI cmd ef/03:01:00:00:00:b0 (SET FEATURES)
filtered out
[29059.904523] ata1.01: ACPI cmd ef/03:20:00:00:00:b0 (SET FEATURES)
filtered out
[29059.928389] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES)
filtered out
[29059.928393] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES)
filtered out
[29059.928397] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE
LOCK) filtered out
[29059.928402] ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE
CONFIGURATION OVERLAY) filtered out
[29059.928814] ata1.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE
MODE) succeeded
[29059.952724] ata1.00: configured for UDMA/100
[29059.968462] ata1.01: configured for MWDMA2
[29060.136235] PM: resume of devices complete after 3130.924 msecs
[29060.136583] PM: Finishing wakeup.
[29060.136585] Restarting tasks ... done.
[29060.173446] video LNXVIDEO:00: Restoring backlight state
[29061.536287] ADDRCONF(NETDEV_UP): eth0: link is not ready
[29061.545128] ADDRCONF(NETDEV_UP): eth1: link is not ready
[29061.548585] ADDRCONF(NETDEV_UP): eth1: link is not ready
[29062.241342] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[29072.312015] eth1: no IPv6 routers present
[29927.648088] usb 3-2: USB disconnect, device number 2
[29933.772093] ADDRCONF(NETDEV_UP): eth1: link is not ready
[29933.773851] ADDRCONF(NETDEV_UP): eth1: link is not ready
[29934.256068] usb 3-2: new full-speed USB device number 3 using
uhci_hcd
[29934.528118] usb 3-2: New USB device found, idVendor=03f0,
idProduct=011d
[29934.528127] usb 3-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[29934.528135] usb 3-2: Product: HP integrated Bluetooth module
[29934.528141] usb 3-2: Manufacturer: Broadcom
[29934.768035] ipw2200: Failed to send CARD_DISABLE: Command timed out.
[29935.598305] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[29946.608069] eth1: no IPv6 routers present
-------------------------------------
On Tue, 2014-08-05 at 02:48 +0200, Tomasz Nitecki wrote:
> tags 756947 + moreinfo
> thanks
>
>
> Hey,
>
> Al, can you please provide us with some more information about your
> system? It would help if you could attach the output of 'lspci',
> 'lsusb', 'lsmod' and 'dmesg' commands. You should run 'dmesg' only after
> the problem occurred.
>
>
> Regards,
> T.
>
--
To UNSUBSCRIBE, email to debian-devel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: https://lists.debian.org/1407284874.4364.1.camel@debian1
