Hey Listmembers After submitting a bugreport it came to my attention that there is a report template which should be used. I therefore submit my bugreport again this time the prober way :)
--------------------------------------------------------------------- Package: installation-reports Debian-installer-version: http://cdimage.debian.org/pub/cdimage-testing/daily/i386/20041004/sarge-i386-netinst.iso I've also used a never image since the last bugreport with the same result. uname -a: Linux (none) 2.6.7-386 Thu Jul 8 05:08:04: EDT 2004 i686 unknown Date: ons okt 6 13:04:37 CEST 2004 Method: Boot from Cdrom Machine: Dell Dimension 8400 Processor: 3Ghz Pentium 4 Memory: 1Gb Ram Chipset: Intel 925X Express chipset Graphics: 128Mb PCIe ATI Radeon X300SE Root Device: Sata ide 160GB HD Root Size/partition table: Disk /dev/scsi/host0/bus0/target0/lun0/disc: 160.0 GB, 160000000000 bytes 255 heads, 63 sectors/track, 19452 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/scsi/host0/bus0/target0/lun0/part1 * 1 851 6835626 83 Linux /dev/scsi/host0/bus0/target0/lun0/part2 852 19452 149412532+ f W95 Ext'd (LBA) /dev/scsi/host0/bus0/target0/lun0/part5 852 1181 2650693+ 82 Linux swap /dev/scsi/host0/bus0/target0/lun0/part6 1182 19452 146761776 83 Linux Added Networkcard : 3com 905 Output of lspci and lspci -n: Both are from knoppix since im not able to boot up in debian and run lspci 00:00.0 Host bridge: Intel Corp.: Unknown device 2584 (rev 04) 00:01.0 PCI bridge: Intel Corp.: Unknown device 2585 (rev 04) 00:1c.0 PCI bridge: Intel Corp.: Unknown device 2660 (rev 03) 00:1c.1 PCI bridge: Intel Corp.: Unknown device 2662 (rev 03) 00:1d.0 USB Controller: Intel Corp.: Unknown device 2658 (rev 03) 00:1d.1 USB Controller: Intel Corp.: Unknown device 2659 (rev 03) 00:1d.2 USB Controller: Intel Corp.: Unknown device 265a (rev 03) 00:1d.3 USB Controller: Intel Corp.: Unknown device 265b (rev 03) 00:1d.7 USB Controller: Intel Corp.: Unknown device 265c (rev 03) 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev d3) 00:1e.2 Multimedia audio controller: Intel Corp.: Unknown device 266e (rev 03) 00:1f.0 ISA bridge: Intel Corp.: Unknown device 2640 (rev 03) 00:1f.1 IDE interface: Intel Corp.: Unknown device 266f (rev 03) 00:1f.2 IDE interface: Intel Corp.: Unknown device 2652 (rev 03) 00:1f.3 SMBus: Intel Corp.: Unknown device 266a (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5b60 01:00.1 Display controller: ATI Technologies Inc: Unknown device 5b70 02:00.0 Ethernet controller: Broadcom Corporation: Unknown device 1677 (rev 01) 04:00.0 FireWire (IEEE 1394): Lucent Microelectronics FW323 (rev 61) 04:02.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74) 00:00.0 Class 0600: 8086:2584 (rev 04) 00:01.0 Class 0604: 8086:2585 (rev 04) 00:1c.0 Class 0604: 8086:2660 (rev 03) 00:1c.1 Class 0604: 8086:2662 (rev 03) 00:1d.0 Class 0c03: 8086:2658 (rev 03) 00:1d.1 Class 0c03: 8086:2659 (rev 03) 00:1d.2 Class 0c03: 8086:265a (rev 03) 00:1d.3 Class 0c03: 8086:265b (rev 03) 00:1d.7 Class 0c03: 8086:265c (rev 03) 00:1e.0 Class 0604: 8086:244e (rev d3) 00:1e.2 Class 0401: 8086:266e (rev 03) 00:1f.0 Class 0601: 8086:2640 (rev 03) 00:1f.1 Class 0101: 8086:266f (rev 03) 00:1f.2 Class 0101: 8086:2652 (rev 03) 00:1f.3 Class 0c05: 8086:266a (rev 03) 01:00.0 Class 0300: 1002:5b60 01:00.1 Class 0380: 1002:5b70 02:00.0 Class 0200: 14e4:1677 (rev 01) 04:00.0 Class 0c00: 11c1:5811 (rev 61) 04:02.0 Class 0200: 10b7:9200 (rev 74) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [0] Configure network HW: [0] Config network: [0] Detect CD: [0] Load installer modules: [0] Detect hard drives: [E/0] se below Partition hard drives: [0] Create file systems: [0] Mount partitions: [0] Install base system: [0] Install boot loader: [0] Reboot: [E] Comments/Problems: As you can se on the Base System Installation Checklist the installation goes fine pretty much the hole way until reboot after installation where the kernel stops around Real Time Clock Driver v1.12. Ive not been able to boot via console to get the full output from kernel but ive attached the syslog and demsg from the installation (i got openssh-client up and running in the install) thanks to Hydroxid from #debian-boot on freenode you guys rock!! :) Hope this helps and im ofcause available for more info or test or whatever should it be needed. /Thomas -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
