sorry.. the original message is a bit fuzzy.. I forgot to put it in
plain text: this is the clean version:
I have an old Buffalo Linkstation Duo (WXL), that now I would like to
use as a backup for my new NAS
I've bumped into RogerShimizu's presentation at
https://miniconf.debian.or.jp/assets/files/Debian%20Installer%20for%20Buffalo%20Linkstation%20NAS.pdf,
in order to update a bit the system with a fresh new debian install; I
followed it and I now have a running Debian system , but:
ￜￜ --ￜￜￜ the only way to shutdown the unit is to put the physical
button in the off position, otherwise both poweroff and shutdown
commands lead to a reboot of the unit
ￜￜ -- ￜￜ wakeonlan is not available:
ￜￜￜￜￜￜￜ ethtool responds "Supports Wake-on: d", and trying to set it
ends in:ￜ "Cannot set new wake-on-lan settings: Operation not supported"
> a@debian:~$ sudo ethtool eth0
> Settings for eth0:
>ￜￜￜￜ Supported ports: [ TP MII ]
>ￜￜￜￜ Supported link modes:ￜￜ 10baseT/Half 10baseT/Full
>ￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜ
100baseT/Half 100baseT/Full
>ￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜ
1000baseT/Full
>ￜￜￜￜ Supported pause frame use: Symmetric Receive-only
>ￜￜￜￜ Supports auto-negotiation: Yes
>ￜￜￜￜ Advertised link modes:ￜ 10baseT/Half 10baseT/Full
>ￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜ
100baseT/Half 100baseT/Full
>ￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜ
1000baseT/Full
>ￜￜￜￜ Advertised pause frame use: No
>ￜￜￜￜ Advertised auto-negotiation: Yes
>ￜￜￜￜ Link partner advertised link modes:ￜ 10baseT/Half 10baseT/Full
>ￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜ
100baseT/Half 100baseT/Full
>ￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜￜ
1000baseT/Full
>ￜￜￜￜ Link partner advertised pause frame use: Symmetric Receive-only
>ￜￜￜￜ Link partner advertised auto-negotiation: Yes
>ￜￜￜￜ Speed: 1000Mb/s
>ￜￜￜￜ Duplex: Full
>ￜￜￜￜ Port: MII
>ￜￜￜￜ PHYAD: 8
>ￜￜￜￜ Transceiver: internal
>ￜￜￜￜ Auto-negotiation: on
>ￜￜￜￜ Supports Wake-on: d
>ￜￜￜￜ Wake-on: d
>ￜￜￜￜ Link detected: yes
obviously with the original buffalo firmware, it worked!
I've tried, under Roger's suggestion, to add "marvell" to
/etc/initramfs-tools/modules, but nothing changed: it seems that the NIC
is not enable for wakeonlaￜ (even if it was, of course)
now I'm wondering if it could be a driver issue, and if is there any
other module that can be used instead of the mv643xx_eth
> a@debian:~$ sudo dmesg |grep eth
> [ￜￜￜ 0.022487] [Firmware Info]:
/ocp@f1000000/ethernet-controller@76000/ethernet1-port@0:
local-mac-address is not set
> [ￜￜ 20.475943] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver
version 1.4
> [ￜￜ 20.593063] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with
MAC address 00:24:a5:47:96:af
> [ￜￜ 34.213593] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ￜￜ 36.875031] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up,
1000 Mb/s, full duplex, flow control disabled
> [ￜￜ 36.885480] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
and now I'm stuck here... My idea to use this old unit as a
"semi-remote" (in the same LAN)backup of the new NAS doesn't work, if
I'm not able to switch it off and on when neededl
any suggestion?
thanks in advance
Rosanna
