On 10/26/2009 07:23 PM, Jonas Häggqvist wrote: > Martin Michlmayr wrote: >> * Jonas Häggqvist <ras...@rasher.dk> [2009-10-27 00:38]: >>> Marvell>> setenv bootcmd_mmc 'mmcinit; ext2load mmc 0 0x0800000 >>> /boot/uInitrd; ext2load mmc 0 0x400000 /boot/uImage' >> >> I'm not sure, but can you try >> >> setenv bootcmd_mmc 'mmcinit; ext2load mmc 0:1 0x0800000 /boot/uInitrd; >> ext2load mmc 0:1 0x400000 /boot/uImage' >> or >> setenv bootcmd_mmc 'mmcinit; ext2load mmc 0:2 0x0800000 /boot/uInitrd; >> ext2load mmc 0:2 0x400000 /boot/uImage' > > Neither of these seemed to help. > >> Is your root partition the first primary partition on the SD card or >> which one? > > It's the first partition. Dump from fdisk: > > Device Boot Start End Blocks Id System > /dev/mmcblk0p1 1 97 779121 83 Linux > /dev/mmcblk0p2 98 123 208845 82 Linux swap > / Solaris > > Output of printenv (with the second bootcmd_mmc): > > baudrate=115200 > loads_echo=0 > rootpath=/mnt/ARM_FS/ > netmask=255.255.0.0 > console=a0000 > e=ttyS0,115200 > CASset=min > MALLOC_len=1 > ethprime=egiga0 > bootargs_root=root=/dev/mtdblock2 ro > ethmtu=1500 > usb0Mode=host > nandEcc=1bit > ethact=egiga0 > serverip=10.10.0.2 > ipaddr=10.10.0.1 > cesvcid=ULULULULULULPPULULULULULDA > bootargs_end=:::DB88FXX81:eth0:none > image_name=uImage > standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) > root=/dev/mtdblock0 rw ip=$(ipaddr):$(serve; > mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs > mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 > yuk_ethaddr=00:00:00:EE:51:81 > netretry=no > rcvrip=169.254.100.100 > loadaddr=0x02000000 > autoload=no > ethaddr=00:50:43:01:65:0C > run_diag=no > arcNumber=2097 > stdin=serial > stdout=serial > stderr=serial > nandEnvBase=a0000 > mainlineLinux=yes > enaMonExt=no > enaCpuStream=no > enaWrAllo=no > pexMode=RC > disL2Cache=no > setL2CacheWT=yes > disL2Prefetch=yes > enaICPref=yes > enaDCPref=yes > sata_dma_mode=yes > netbsd_en=no > vxworks_en=no > bootdelay=3 > disaMvPnp=no > enaAutoRecovery=yes > pcieTune=no > bootargs_console=console=ttyS0,115200 > bootcmd=setenv bootargs $(bootargs_console); run bootcmd_mmc; bootm > 0x400000 0x0800000 > bootcmd_mmc=mmcinit; ext2load mmc 0:2 0x0800000 /boot/uInitrd; ext2load > mmc 0:2 0x400000 /boot/uImage > bootargs=console=ttyS0,115200 > > Environment size: 1349/131068 bytes >
I haven't spotted a correction I might suggest, but if it helps at all, I have kept all my configurations from the default factory configs, through dual-boot SD|NAND, which is what I'm using currently - perhaps they will give you an idea or two. http://12.am/sheevaplug/ -- Kind regards, Michael -- To UNSUBSCRIBE, email to debian-arm-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
