zhuyanlinzyl edited a comment on pull request #5336:
URL: https://github.com/apache/incubator-nuttx/pull/5336#issuecomment-1042545274
@Ouss4 :
> These are internal CPU interrupts, which means each CPU has both
ESP32_CPUINT_SOFTWARE0 and ESP32_CPUINT_SOFTWARE1. They have the same
interrupt number but controlled from each CPU's registers.
So each CPU have separate internal interrupts，Such as
`ESP32_CPUINT_SOFTWARE1` and
`ESP32_CPUINT_TIMER0`
Then I think the g_irqmap must be g_irqmap[CONFIG_SMP_NCPUS] for internal
interrupts.
Is my understanding correct?
> The thing that I see is going to be a bit messy is how we dispatch the
interrupts. Since they have the same numbers so in NuttX they will have the
same irq number.
I don't think dispatch interrupts is a problem. As every CPU only have one
interrupt per number , They handle their own interrupts independently.We can
same interrupt pin.
I have modify up_enable_irq with this patch
```
if (irq < XTENSA_NIRQ_INTERNAL)
{
- /* Enable the CPU interrupt now for internal CPU. */
+ /* Enable the CPU interrupt now for internal CPU. */
+ if ((irq == 4) && (up_cpu_index() == 0))
+ {
+ cpu = 0;
+ }
xtensa_enable_cpuint(&g_intenable[cpu], (1ul << cpuint));
}
```
The the smp config work well.
```
zyl@zyl:~/nuttx$ qemu-system-xtensa -nographic -machine esp32 -smp 2 -drive
file=./nuttx.merged.bin,if=mtd,format=raw
==3509606==WARNING: ASan doesn't fully support makecontext/swapcontext
functions and may produce false positives in some cases!
Adding SPI flash device
ets Jul 29 2019 12:21:46
rst:0x1 (POWERON_RESET),boot:0x12 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:6604
ho 0 tail 12 room 4
load:0x40078000,len:14780
load:0x40080400,len:3792
entry 0x40080694
I (1017) boot: ESP-IDF v4.4 2nd stage bootloader
I (1031) boot: compile time 19:32:08
I (1053) boot: chip revision: 0
I (1069) boot.esp32: SPI Speed : 40MHz
I (1072) boot.esp32: SPI Mode : DIO
I (1074) boot.esp32: SPI Flash Size : 4MB
I (1097) boot: Enabling RNG early entropy source...
I (1129) boot: Partition Table:
I (1130) boot: ## Label Usage Type ST Offset Length
I (1132) boot: 0 factory factory app 00 00 00010000 00100000
I (1150) boot: End of partition table
I (1169) esp_image: segment 0: paddr=00010020 vaddr=3f400020 size=08708h (
34568) map
I (1270) esp_image: segment 1: paddr=00018730 vaddr=3ffb3ce0 size=00100h (
256) load
I (1305) esp_image: segment 2: paddr=00018838 vaddr=40080000 size=01c58h (
7256) load
I (1357) esp_image: segment 3: paddr=0001a498 vaddr=00000000 size=05b80h (
23424)
I (1428) esp_image: segment 4: paddr=00020020 vaddr=400d0020 size=170e0h (
94432) map
I (1632) boot: Loaded app from partition at offset 0x10000
I (1636) boot: Disabling RNG early entropy source...
NuttShell (NSH) NuttX-10.2.0
nsh> ps
PID GROUP CPU PRI POLICY TYPE NPX STATE EVENT SIGMASK STACK
USED FILLED COMMAND
0 0 0 0 FIFO Kthread N-- Assigned 00000000 003040
000976 32.1% CPU0 IDLE
1 1 1 0 FIFO Kthread N-- Running 00000000 003040
000640 21.0% CPU1 IDLE
2 2 0 100 RR Task --- Running 00000000 002000
001840 92.0%! nsh_main
```
--
This is an automated message from the Apache Git Service.
To respond to the message, please log on to GitHub and use the
URL above to go to the specific comment.
To unsubscribe, e-mail: [email protected]
For queries about this service, please contact Infrastructure at:
[email protected]
