Have you tried an extraction tool? I can mail it to you... Sent from my Android. Please forgive typos. Thank you.
________________________________ From: CnC-List <cnc-list-boun...@cnc-list.com> on behalf of John Conklin via CnC-List <cnc-list@cnc-list.com> Sent: Saturday, March 21, 2020 5:11:01 PM To: cnc-list@cnc-list.com <cnc-list@cnc-list.com> Cc: John Conklin <jconk...@hotmail.com> Subject: Re: Stus-List Boat projects again- wire running through rail tube Following as I cannot remove the lense on my bow light :( small top and bottom Phillips head are stripped. Even hit em with PB blaster This needs to come of to get to 2 bolts the hold casing to pulpit. I have whole new set up But hoping there may be a solution? Before smashing it ! John Conklin S/V Halcyon S/V Heartbeat www.flirtingwithfire.com On Mar 20, 2020, at 10:08 PM, David Knecht via CnC-List <cnc-list@cnc-list.com> wrote: You win the prize Edd. Got in there with a dental pick and fine screwdriver near the tube exit and managed to free it and pull it out. Thanks for the help. But that was only the first of the problems with the new lights. Will post tomorrow when I calm down so not too inflamatory. Dave On Mar 20, 2020, at 10:22 AM, Edd Schillay via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: David, When I did some rewiring (on the 37+), there was some sealant inside the tube, and it was keeping the wire from moving. I used a very fine screwdriver to “pick" it free. All the best, Edd Edd M. Schillay Captain of the Starship Enterprise C&C 37+ | Sail No: NCC-1701-B Venice Yacht Club | Venice Island, FL Starship Enterprise's Captain's Log<http://enterpriseb.blogspot.com/> On Mar 20, 2020, at 10:16 AM, Dennis C. via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: It may be sealant at the deck. Does the vertical tube go into a deck fitting? If so, remove any set screws and try to lift the tube. You may have to do the same to an adjacent tube. Once you lift the tube you may see your issue. Dennis C. Touche' 35-1 #83 Mandeville, LA On Fri, Mar 20, 2020 at 9:10 AM David Knecht via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: I had another problem the other day that I can’t figure out. I am replacing the bow and stern lights with LED. The wire from the old stern light runs into the stainless steel vertical tube of the rear rail and down into the port lazarette. I have been unable to budge the wire by pulling on it from the bottom even though it appears loose at the top. The bow lights are similar and the wire pulls out easily. I can’t see anything holding the wire so I am wondering if anyone has ideas or has encountered this problem and solved it. Thanks- Dave David Knecht S/V Aries 1990 C&C 34+ New London, CT <pastedGraphic.tiff> _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray David Knecht S/V Aries 1990 C&C 34+ New London, CT <pastedGraphic.tiff> _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
_______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
