I've seen installers put a know in the wire at a juncture so it wont pull out....; Richard s/v Bushmark4: 1985 C&C 37 CB; Richard N. Bush Law Offices 2950 Breckenridge Lane, Suite Nine Louisville, Kentucky 40220-1462 502-584-7255 -----Original Message----- From: David Risch via CnC-List <cnc-list@cnc-list.com> To: cnc-list@cnc-list.com <cnc-list@cnc-list.com> Cc: David Risch <davidrisc...@msn.com> Sent: Fri, Mar 20, 2020 10:59 am Subject: Re: Stus-List Boat projects again- wire running through rail tube
I rewired my bow light. Had to remove pulpit leg to get wire through a small deck hole hidden by tube. Sent from my Android. Please forgive typos. Thank you. From: CnC-List <cnc-list-boun...@cnc-list.com> on behalf of Edd Schillay via CnC-List <cnc-list@cnc-list.com> Sent: Friday, March 20, 2020 10:22:18 AM To: Edd Schillay via CnC-List <cnc-list@cnc-list.com> Cc: Edd Schillay <e...@schillay.com> Subject: Re: Stus-List Boat projects again- wire running through rail tube David, When I did some rewiring (on the 37+), there was some sealant inside the tube, and it was keeping the wire from moving. I used a very fine screwdriver to “pick" it free. All the best, Edd Edd M. SchillayCaptain of the Starship EnterpriseC&C 37+ | Sail No: NCC-1701-BVenice Yacht Club | Venice Island, FL Starship Enterprise's Captain's Log On Mar 20, 2020, at 10:16 AM, Dennis C. via CnC-List <cnc-list@cnc-list.com> wrote: It may be sealant at the deck. Does the vertical tube go into a deck fitting? If so, remove any set screws and try to lift the tube. You may have to do the same to an adjacent tube. Once you lift the tube you may see your issue. Dennis C.Touche' 35-1 #83Mandeville, LA On Fri, Mar 20, 2020 at 9:10 AM David Knecht via CnC-List <cnc-list@cnc-list.com> wrote: I had another problem the other day that I can’t figure out. I am replacing the bow and stern lights with LED. The wire from the old stern light runs into the stainless steel vertical tube of the rear rail and down into the port lazarette. I have been unable to budge the wire by pulling on it from the bottom even though it appears loose at the top. The bow lights are similar and the wire pulls out easily. I can’t see anything holding the wire so I am wondering if anyone has ideas or has encountered this problem and solved it. Thanks- Dave David KnechtS/V Aries1990 C&C 34+New London, CT <pastedGraphic.tiff> _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
_______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
