Russ, I didn’t say whats going into the bilge!!

Chuck, thank you for the suggestion. We are actually sailing and will be at the 
New Bedford Yacht club next week. 


> On Jul 31, 2017, at 7:47 PM, Russ & Melody via CnC-List 
> <cnc-list@cnc-list.com> wrote:
> 
> 
> I didn't find increase beer stowage and wine locker volume and adding an ice 
> maker in this list.
> 
>         cheers, Russ
>         Sweet 35 mk-1
> sent from an old HP machine, running XP
> 
> At 03:48 PM 31/07/2017, you wrote:
>> New Steering chain and cables. Pedestal wheel shaft bearing lubrication or 
>> replacement. Check steering idler below pedestal (sheaves, bearings, 
>> corrosion).
>> It is unwise to spend countless hours "varnishing" and installing gadgets to 
>> prep for a cruise but give no thought to the steering system.
>> Chuck Gilchrest 
>> S/V Half Magic
>> 1983 35 Landfall
>> Padanaram, MA
>> 
>> Sent from my iPhone
>> 
>> On Jul 31, 2017, at 6:35 PM, john wright via CnC-List <cnc-list@cnc-list.com 
>> <mailto:cnc-list@cnc-list.com>> wrote:
>> 
>>> Hello everyone
>>> 
>>> I am about to begin a complete refit on what is the best boat  for my 
>>> purpose ( sailing around Cape Code as we get ready to do the Caribbean 1500 
>>> in 2019), after looking or sailing at least 100 boat over the past 4 years. 
>>> The boat is in better than average condition, I will post pictures later.
>>> 
>>> I have the work broken down into three categories, and would appreciate any 
>>> recommendations and reorganizing of the list. 
>>> 
>>> Thanks
>>> 
>>> Level 1: Repairs and Installations
>>> Replace old set of AGM batteries with new set
>>> Remove old engine, clean and repaint engine room, rebuild engine bed as 
>>> needed to fit the new Yanmar 3JH5e
>>> Replace all hoses for new engine
>>> Move raw water sea strainer and Racor fuel filter to easier location to 
>>> monitor visually
>>> Gelcoat – fill all chips and nicks with gelcoatt
>>> Clean stains with FSR
>>> Repair teak grating at pedestal (epoxy the connections to frame)
>>> Clean teak with teak cleaner
>>> Replace teak combing with thicker mahogany boards
>>> Clean and Polish all gelcoat surfaces 
>>> Hull bottom – sand and repaint withh anti-fouling ablative paint 
>>> Re-install mast and tune rigging
>>> Make line hanger in cockpit below deck winches functional once again
>>> Add gasket to aft access panel under helm seat
>>> Repair/ refinish wood framework to companionway
>>> Re-varnish companionway door
>>> Make better drainage in port cockpit locker and revarnish partition wood
>>> Install the new Whale Gusher manual pump in cockpit
>>> Update propane solenoid 
>>> Remake companionway door cover to fit better
>>> Deck and House – clean and re-varnish woodwork (handrails, dorade boxes)
>>> Clean and polish all stainless hardware
>>> Replace gasket material on all opening ports
>>> Repaint all dorade vents
>>> Replace traveler cam cleat
>>> Clean, sand and varnish bow platform
>>> Stanchion support on starboard bent – take to shop and straighten
>>> Add maintenance coat of varnish on floors and re-secure
>>> Install and varnish framework for windows
>>> Repair and revarnish bulkheads where needed
>>> Re-install all cabinets and tables
>>> Finish installation of canvas cover for ceiling in forward berth
>>> Ice box cover – installl hardware and gasket
>>> Head – re-cut new mirror aand install
>>> Forward cabin has trim work that needs to be installed
>>> Brow in forward cabin to be replaced with new trim work
>>> 
>>> 
>>> Level 2: Updates and Improvements
>>> Hull repainting – large project to be deescribed as we get closer to that 
>>> project
>>> Paint steering pedestal white
>>> Replace instruments
>>> Replace opening port in cockpit with new
>>> Add winch handle holders in cockpit
>>> Paint new non-skid in cockpit seats and floor
>>> Make set of cockpit cushions
>>> Install a cockpit shower
>>> Re-bed all deck gear, hardware and chainplates (last another 20 years)
>>> Replace all blocks with updated equipment
>>> Replace all running rigging
>>> Replace genoa sheet cars with moveable sheet lead under load
>>> Replace missing wood bungs on teak toe rail (may need to reset screws 
>>> deeper as wood has shrunk over time)
>>> Sand toe rail and varnish
>>> Winches to be stripped cleaned and greased
>>> Paint interior of chain locker
>>> Make a grating for chain locker to help rode to dry
>>> Stanchion bases and cleats to be removed and powder coated to original color
>>> All deck non-skid to be renewed with white or Hatteras soft yellow (Tartan 
>>> Yachts uses this style)
>>> Add stanchion rollers for headsail furling line to lead to cockpit
>>> Replace steering cables with new
>>> Replace all interior lighting with LED
>>> Install Isotherm hot water tank
>>> Replace interior cushions with new foam and fabrics
>>> Replace AC/DC switch panel with BluSea panel
>>> Add swim ladder
>>> 
>>> 
>>> Level 3: Enhancements
>>> Replace manual windlass with an electric version
>>> Upgrade chain and rope to fit new windlass
>>> Add pad-eye on bow platform for code zero sail
>>> Add Fischer Panda Perfect Power iSeries Generator
>>> Install reverse cycle heat and air conditioning system
>>> Add custom fitted mattress for sleeping berths
>>> New mainsail with deep double reef and Harken bat car track for ease of 
>>> hoist
>>> Stack-pack for mainsail storage (see MacSails of Florida)
>>> Gooseneck double reefing hook from South Shore Yachts
>>> Replace standing rod rigging for peace of mind
>>> Add Code Zero sail on Facnor continuous line furling unit
>>> Add Wisker pole
>>> Upgrade roller furling unit
>>> Add Mantus anchor
> _______________________________________________
> 
> This list is supported by the generous donations of our members. If you wish 
> to make a contribution to offset our costs, please go to:  
> https://www.paypal.me/stumurray
> 
> All Contributions are greatly appreciated!

_______________________________________________

This list is supported by the generous donations of our members. If you wish to 
make a contribution to offset our costs, please go to:  
https://www.paypal.me/stumurray

All Contributions are greatly appreciated!

Reply via email to