I didn't find increase beer stowage and wine
locker volume and adding an ice maker in this list.
cheers, Russ
Sweet 35 mk-1
sent from an old HP machine, running XP
At 03:48 PM 31/07/2017, you wrote:
New Steering chain and cables. Pedestal wheel
shaft bearing lubrication or replacement. Check
steering idler below pedestal (sheaves, bearings, corrosion).
It is unwise to spend countless hours
"varnishing" and installing gadgets to prep for
a cruise but give no thought to the steering system.
Chuck Gilchrest
S/V Half Magic
1983 35 Landfall
Padanaram, MA
Sent from my iPhone
On Jul 31, 2017, at 6:35 PM, john wright via
CnC-List <<mailto:cnc-list@cnc-list.com>cnc-list@cnc-list.com> wrote:
Hello everyone
I am about to begin a complete refit on what is
the best boat for my purpose ( sailing around
Cape Code as we get ready to do the Caribbean
1500 in 2019), after looking or sailing at
least 100 boat over the past 4 years. The boat
is in better than average condition, I will post pictures later.
I have the work broken down into three
categories, and would appreciate any
recommendations and reorganizing of the list.
Thanks
Level 1: Repairs and Installations
Replace old set of AGM batteries with new set
Remove old engine, clean and repaint engine
room, rebuild engine bed as needed to fit the new Yanmar 3JH5e
Replace all hoses for new engine
Move raw water sea strainer and Racor fuel
filter to easier location to monitor visually
Gelcoat fill all chips and nicks with gelcoatt
Clean stains with FSR
Repair teak grating at pedestal (epoxy the connections to frame)
Clean teak with teak cleaner
Replace teak combing with thicker mahogany boards
Clean and Polish all gelcoat surfaces
Hull bottom sand and repaint withh anti-fouling ablative paint
Re-install mast and tune rigging
Make line hanger in cockpit below deck winches functional once again
Add gasket to aft access panel under helm seat
Repair/ refinish wood framework to companionway
Re-varnish companionway door
Make better drainage in port cockpit locker and revarnish partition wood
Install the new Whale Gusher manual pump in cockpit
Update propane solenoid
Remake companionway door cover to fit better
Deck and House clean and re-varnish woodwork (handrails, dorade boxes)
Clean and polish all stainless hardware
Replace gasket material on all opening ports
Repaint all dorade vents
Replace traveler cam cleat
Clean, sand and varnish bow platform
Stanchion support on starboard bent take to shop and straighten
Add maintenance coat of varnish on floors and re-secure
Install and varnish framework for windows
Repair and revarnish bulkheads where needed
Re-install all cabinets and tables
Finish installation of canvas cover for ceiling in forward berth
Ice box cover installl hardware and gasket
Head re-cut new mirror aand install
Forward cabin has trim work that needs to be installed
Brow in forward cabin to be replaced with new trim work
Level 2: Updates and Improvements
Hull repainting large project to be
deescribed as we get closer to that project
Paint steering pedestal white
Replace instruments
Replace opening port in cockpit with new
Add winch handle holders in cockpit
Paint new non-skid in cockpit seats and floor
Make set of cockpit cushions
Install a cockpit shower
Re-bed all deck gear, hardware and chainplates (last another 20 years)
Replace all blocks with updated equipment
Replace all running rigging
Replace genoa sheet cars with moveable sheet lead under load
Replace missing wood bungs on teak toe rail
(may need to reset screws deeper as wood has shrunk over time)
Sand toe rail and varnish
Winches to be stripped cleaned and greased
Paint interior of chain locker
Make a grating for chain locker to help rode to dry
Stanchion bases and cleats to be removed and powder coated to original color
All deck non-skid to be renewed with white or
Hatteras soft yellow (Tartan Yachts uses this style)
Add stanchion rollers for headsail furling line to lead to cockpit
Replace steering cables with new
Replace all interior lighting with LED
Install Isotherm hot water tank
Replace interior cushions with new foam and fabrics
Replace AC/DC switch panel with BluSea panel
Add swim ladder
Level 3: Enhancements
Replace manual windlass with an electric version
Upgrade chain and rope to fit new windlass
Add pad-eye on bow platform for code zero sail
Add Fischer Panda Perfect Power iSeries Generator
Install reverse cycle heat and air conditioning system
Add custom fitted mattress for sleeping berths
New mainsail with deep double reef and Harken bat car track for ease of hoist
Stack-pack for mainsail storage (see MacSails of Florida)
Gooseneck double reefing hook from South Shore Yachts
Replace standing rod rigging for peace of mind
Add Code Zero sail on Facnor continuous line furling unit
Add Wisker pole
Upgrade roller furling unit
Add Mantus anchor
_______________________________________________
This list is supported by the generous donations of our members. If you wish to
make a contribution to offset our costs, please go to:
https://www.paypal.me/stumurray
All Contributions are greatly appreciated!
