I'm pretty sure mine does not have a full length keyway and it didn't have a factory autopilot either.
Ken H. S/V Salazar C&C 37 XL On 12 December 2015 at 21:54, Gary Russell via CnC-List < cnc-list@cnc-list.com> wrote: > Josh, > I'm wondering if all 37 Pluses have a full length keyway, or only > boats with the factory autopilot installation. > > Gary > S/V High Maintenance > '90 C&C 37 Plus > East Greenwich, RI, USA > > ~~~~~~~_/)~~~~~~ > > > On Sat, Dec 12, 2015 at 5:56 PM, Josh Muckley via CnC-List < > cnc-list@cnc-list.com> wrote: > >> Gary, >> >> Autopilot was already there. >> >> Keyway goes almost the full length of the rudder stock. >> >> I think this may have been a factory install since the platform in >> Brian's boat looks exactly like mine. >> >> Josh Muckley >> S/V Sea Hawk >> 1989 C&C 37+ >> Solomons, MD >> On Dec 12, 2015 5:02 PM, "Gary Russell via CnC-List" < >> cnc-list@cnc-list.com> wrote: >> >>> Josh, >>> Did you install the autopilot or a PO? If you installed it was the >>> rudder cut out when you got it and did the shaft have a keyway already cut >>> in it. >>> >>> Gary >>> S/V High Maintenance >>> '90 C&C 37 Plus >>> East Greenwich, RI, USA >>> >>> ~~~~~~~_/)~~~~~~ >>> >>> >>> On Fri, Dec 11, 2015 at 6:38 PM, Josh Muckley via CnC-List < >>> cnc-list@cnc-list.com> wrote: >>> >>>> I've removed my rudder arm and it looked nothing like that. It looks >>>> like you are looking at the back side. The 4 bolts accessible from the >>>> front are all you need to remove. >>>> >>>> https://drive.google.com/folder/d/0B8pEh5lnvP1yZU1hczd0QlNEOWc/edit >>>> >>>> https://drive.google.com/folder/d/0B8pEh5lnvP1yVUdWUDNxVGFUcDA/edit >>>> >>>> https://drive.google.com/folder/d/0B8pEh5lnvP1yQWIyanRiTzBKRlk/edit >>>> >>>> Josh Muckley >>>> S/V Sea Hawk >>>> 1989 C&C 37+ >>>> Solomons, MD >>>> On Dec 11, 2015 6:23 PM, "Brian Fry via CnC-List" < >>>> cnc-list@cnc-list.com> wrote: >>>> >>>>> Hello, my name is Brian. I recently bought La Neige, a 1993 37/40xl. >>>>> I am in the Chesapeake. >>>>> >>>>> http://i.imgur.com/5faMwZ9.jpg >>>>> >>>>> The link is to a picture of my C&C 37/40 auto pilot clamp, where it >>>>> attaches to the rudder shaft. The threaded rod has no bolt head to unscrew >>>>> the rod. >>>>> Has anyone dealt with this issue? I need to drop my rudder, and this >>>>> is not allowing that to happen. >>>>> . >>>>> >>>>> _______________________________________________ >>>>> >>>>> Email address: >>>>> CnC-List@cnc-list.com >>>>> To change your list preferences, including unsubscribing -- go to the >>>>> bottom of page at: >>>>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>>>> >>>>> >>>>> >>>> _______________________________________________ >>>> >>>> Email address: >>>> CnC-List@cnc-list.com >>>> To change your list preferences, including unsubscribing -- go to the >>>> bottom of page at: >>>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>>> >>>> >>>> >>> >>> _______________________________________________ >>> >>> Email address: >>> CnC-List@cnc-list.com >>> To change your list preferences, including unsubscribing -- go to the >>> bottom of page at: >>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>> >>> >>> >> _______________________________________________ >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go to the >> bottom of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > >
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
