Pretty sure that the 30, 34, and 37 series boats are all centerline. Past discussions indicated that the angle at which the shaft leaves the hull (angle down) influences the pull. The swirling column of water..... On Aug 26, 2015 2:19 PM, "David Knecht via CnC-List" <cnc-list@cnc-list.com> wrote:
> Hi Bill- I am not sure about the offset. I did not realize that it was a > possibility. I will have to check this winter when on the hard. I have a > vague recollection of it not being straight relative to the axis of the > boat and that might be why. If so, I guess that would explain the pull. > Dave > > Aries > 1990 C&C 34+ > New London, CT > > > On Aug 26, 2015, at 2:02 PM, Bill Coleman via CnC-List < > cnc-list@cnc-list.com> wrote: > > Is your prop shaft offset so it can be removed past the rudder? > > Bill Coleman > C&C 39 > *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com > <cnc-list-boun...@cnc-list.com>] *On Behalf Of *David Knecht via CnC-List > *Sent:* Wednesday, August 26, 2015 1:44 PM > *To:* CnC CnC discussion list > *Cc:* David Knecht > *Subject:* Re: Stus-List Autopilot steering > > Calling Raymarine was my first action and I am waiting for a call back. > But what I really want to know from the group is whether the relatively > strong pull to port while motoring is normal or whether neutral helm is > normal. Dave > > Aries > 1990 C&C 34+ > New London, CT > > <image001.png> > > > On Aug 26, 2015, at 1:03 PM, David via CnC-List <cnc-list@cnc-list.com> > wrote: > > > yep...call Raymarine > > David F. Risch > (401) 419-4650 (cell) > > ------------------------------ > Date: Wed, 26 Aug 2015 12:52:24 -0400 > To: cnc-list@cnc-list.com > Subject: Re: Stus-List Autopilot steering > From: cnc-list@cnc-list.com > CC: davidakne...@gmail.com > > No- It is smooth by hand. No stiffness I have noticed. > > Aries > 1990 C&C 34+ > New London, CT > > <pastedGraphic.tiff> > > > On Aug 26, 2015, at 12:50 PM, David via CnC-List <cnc-list@cnc-list.com> > wrote: > > > Does the steering hang up at all when the autopilot is disengaged? > > David F. Risch > 1981 40-2 > (401) 419-4650 (cell) > > ------------------------------ > Date: Wed, 26 Aug 2015 12:04:11 -0400 > To: CnC-List@cnc-list.com > Subject: Stus-List Autopilot steering > From: cnc-list@cnc-list.com > CC: davidakne...@gmail.com > > I was on a long cruise last weekend and we ended up motoring for many > hours. installed a new Raymarine EV1/ST4000+ wheel pilot last winter and > this was the first extended use. I found that it was frequently cutting > out while motoring (not sailing). The unit would simply freeze up and stop > steering while the boat drifted slowly off course. No error on the P70 > controller screen until I got an off course warning. I also noticed the > wheel pilot getting warm/hot when this was happening which may be why it > cut out. > I also notice that while motoring, there is significant pull on the wheel > that has to be fought to keep the boat going straight. Is that normal? I > am guessing that the wheel pilot is overheating due to the power needed to > continuously fight that pull? Thanks- Dave > > Aries > 1990 C&C 34+ > New London, CT > > <pastedGraphic.tiff> > > > _______________________________________________ Email address: > CnC-List@cnc-list.com To change your list preferences, including > unsubscribing -- go to the bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > _______________________________________________ Email address: > CnC-List@cnc-list.com To change your list preferences, including > unsubscribing -- go to the bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > >
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
