Gelcoat won’t stick to epoxy, so unless you intend to repaint the boat in the 
near future don’t use epoxy.

 

Dennis C can wade in on the subject, but in my experience it will take just 
about the same amount of time to do a patch with epoxy as it will to do a 
repair with polyester and gelcoat…. So why do it twice?

 

I recently did repairs on a C&C 29 that had a long (but shallow) gash in the 
topsides, a spot where the port stern cleat had been torn out of the deck and a 
shoddy attempt made at a repair, and two areas in the deck where lifeline 
stanchions had done damage resulting in a leak. In all I had about 6-7 hours of 
grinding and glass work to lay up patches and restore the gelcoat spread over 4 
days, with more than half of the time spent in matching, applying, and 
smoothing out the gelcoat.

 

Do the job once, but do it right.

 

Rick Brass

Washington, NC

 

 

 

From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Josh Muckley 
via CnC-List
Sent: Sunday, July 05, 2015 3:59 PM
To: C&C List
Cc: Josh Muckley
Subject: Re: Stus-List Damage to fibreglas

 

Ken's statement is my understanding also but aside from the possibility that a 
gelcoat finish won't adhere, I can't understand why anyone would use polyester 
OR vinylester resin for a repair.  Besides when you go to do the job right 
you're going to grind out all the epoxy anyway to feather in a proper layup.

Josh Muckley
S/V Sea Hawk
1989 C&C 37+
Solomons, MD

On Jul 5, 2015 3:23 PM, "Ken Heaton via CnC-List" <cnc-list@cnc-list.com 
<mailto:cnc-list@cnc-list.com> > wrote:

I think the recommendation to seal it out with epoxy is not a good idea unless 
the future repair is certain to be made with epoxy as well.  As I understand 
it, the common polyester resin does not stick properly to epoxy, making more 
work for whoever does the later repair if they do the repair using polyester 
resin.

 

Ken H.

 

On 5 July 2015 at 15:31, Brent Driedger via CnC-List <cnc-list@cnc-list.com 
<mailto:cnc-list@cnc-list.com> > wrote:

I would seal it with West Epoxy and if it's in a structurally important area 
I'd sand out a bevel and add a few layers of glass. It didn't need to be 
pretty.  

Cheers.  

 

Brent

27-5

Lake Winnipeg


Sent from my iPhone


On Jul 5, 2015, at 12:57 PM, Fred Hazzard via CnC-List <cnc-list@cnc-list.com 
<mailto:cnc-list@cnc-list.com> > wrote:

I put a hole in several layers of fibreglas about a foot above the waterline in 
the side of my boat.  As it may take some time before repairs are made,  should 
I seal the glass to prevent water from getting in the layup?  If so what should 
I use?

 

Fred Hazzard

S/V Fury

Portland, Or

_______________________________________________

Email address:
CnC-List@cnc-list.com <mailto:CnC-List@cnc-list.com> 
To change your list preferences, including unsubscribing -- go to the bottom of 
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com


_______________________________________________

Email address:
CnC-List@cnc-list.com <mailto:CnC-List@cnc-list.com> 
To change your list preferences, including unsubscribing -- go to the bottom of 
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com



 


_______________________________________________

Email address:
CnC-List@cnc-list.com <mailto:CnC-List@cnc-list.com> 
To change your list preferences, including unsubscribing -- go to the bottom of 
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com



_______________________________________________

Email address:
CnC-List@cnc-list.com
To change your list preferences, including unsubscribing -- go to the bottom of 
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com

Reply via email to