Reminded me I have a RAM mount and laptop "table" that I used to use to secure my laptop on board. Now taking up space in my basement. RAM clamp attaches to vertical 1" (?) pole in corner of chart table.
Not sure of its value - if any. Can sent photos if anyone is interested -- Jonathan Indigo C&C 35III SOUTHPORT CT > On Oct 1, 2014, at 11:56, Joel Aronson via CnC-List <cnc-list@cnc-list.com> > wrote: > > I would look at RAM mounts. > > My 35/3 has a 9 inch guard I believe. > > Joel > >> On Wed, Oct 1, 2014 at 11:46 AM, Tim Goodyear via CnC-List >> <cnc-list@cnc-list.com> wrote: >> I use an Edson arm (also costing more than your GPS) for a Garmin 5" plotter: >> >> http://www.edsonmarine.com/marinestore/index.php?main_page=product_info&cPath=87_100&products_id=430 >> >> Tim >> Mojito >> C&C 35-3 >> >>> On Wed, Oct 1, 2014 at 11:19 AM, Della Barba, Joe via CnC-List >>> <cnc-list@cnc-list.com> wrote: >>> I just got a Standard-Horizon CP180 GPS/chartplotter/fishfinder/radar from >>> Fleabay for a good price. This is a 5 inch screen unit that is about 8”x5”. >>> I am in a bit of a quandary on where to mount it. On the bulkhead at the >>> forward end of the cockpit will make wiring easier and be fairly protected >>> from the weather. I usually am in the forward cockpit underway with the >>> autopilot remote. For tricky situations where I am at the helm I would love >>> it to be mounted on the binnacle, but I am not sure if I like the idea of >>> it being so exposed. Has anyone tried putting a navpod on a MK I? Does the >>> MK I binnacle guard have the standard 12” spacing or something else? >>> >>> I already have a PC plotter setup that I like, but that draws about 36 >>> watts. This unit should be more like 6 watts and can support a radar if I >>> want to add the antenna. If I cable it right I can send waypoints back and >>> forth from the PC to the plotter. Only downside so far is I need a $170 >>> chart chip for a $140 plotter to get any decent level of detail L >>> >>> >>> >>> Joe Della Barba >>> >>> Coquina >>> >>> C&C 35 MK I >>> >>> >>> _______________________________________________ >>> This List is provided by the C&C Photo Album >>> >>> Email address: >>> CnC-List@cnc-list.com >>> To change your list preferences, including unsubscribing -- go bottom of >>> page at: >>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go bottom of >> page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > -- > Joel > 301 541 8551 > _______________________________________________ > This List is provided by the C&C Photo Album > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go bottom of page > at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >
_______________________________________________ This List is provided by the C&C Photo Album Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
